1、BSI Standards PublicationBS EN ISO 8496:2013Metallic materials Tube Ring tensile testBS EN ISO 8496:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 8496:2013.It supersedes BS EN ISO 8496:2004 which is withdrawn.The UK participation in its preparation wa
2、s entrusted to TechnicalCommittee ISE/101/2, Ductility testing.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. Th
3、e British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 82941 3ICS 77.040.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 N
4、ovember 2013.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8496 November 2013 ICS 77.040.10 Supersedes EN ISO 8496:2004English Version Metallic materials - Tube - Ring tensile test (ISO 8496:2013) Matriaux mtalliques - Tubes - Essai de
5、traction sur anneaux (ISO 8496:2013) Metallische Werkstoffe - Rohr - Ringzugversuch (ISO 8496:2013) This European Standard was approved by CEN on 28 October 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standar
6、d the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English,
7、French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulga
8、ria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tur
9、key and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.
10、Ref. No. EN ISO 8496:2013 EBS EN ISO 8496:2013EN ISO 8496:2013 (E) 3 Foreword This document (EN ISO 8496:2013) has been prepared by Technical Committee ISO/TC 164 “Mechanical testing of metals“ in collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” the secr
11、etariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2014, and conflicting national standards shall be withdrawn at the latest by May 2014. Attention is drawn to th
12、e possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 8496:2004. According to the CEN-CENELEC Internal Regulations, the national sta
13、ndards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
14、Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 8496:2013 has been approved by CEN as EN ISO 8496:2013 without any modification. BS EN ISO 8496:2013ISO 8496:2013(E) IS
15、O 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Principle 13 Apparatus . 14 Test piece 25 Procedure. 26 Test report . 2BS EN ISO 8496:2013ISO 8496:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO me
16、mber bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governme
17、ntal and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance
18、 are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is draw
19、n to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on t
20、he ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 164, Mechanical testing of metals, Subcommittee SC 2, Du
21、ctility testing.This third edition cancels and replaces the second edition (ISO 8496:1998), of which it constitutes a minor revision.iv ISO 2013 All rights reservedBS EN ISO 8496:2013INTERNATIONAL STANDARD ISO 8496:2013(E)Metallic materials Tube Ring tensile test1 ScopeThis International Standard sp
22、ecifies a method for a ring tensile test of tubes to reveal surface and internal defects by subjecting the test piece to strain until fracture occurs. This test may also be used to assess the ductility of tubes.The ring tensile test is applicable to tubes having an outside diameter exceeding 150 mm
23、and a wall thickness no greater than 40 mm. The inside diameter shall be greater than 100 mm.2 PrincipleSubjecting a ring cut from the end of a tube to strain in the circumferential direction until fracture occurs.3 ApparatusUse two circular pins, of equal diameter with parallel axes, and movable in
24、 relation to each other while still remaining parallel.In principle, the diameter of the pins shall be the minimum permissible from strength considerations but, provided that the inside diameter of the tube allows, should be at least 3 times the wall thickness of the tube to be tested (see Figure 1)
25、.Dimensions in millimetresFigure 1 ISO 2013 All rights reserved 1BS EN ISO 8496:2013ISO 8496:2013(E)4 Test piece4.1 The test piece shall be a ring cut from the tube with the end faces perpendicular to the axis.4.2 The length of the test piece (width of the ring) shall be approximately 15 mm. If the
26、thickness exceeds 15 mm, the length of the test piece may be equal to the thickness.4.3 The ends of the test piece shall be free from burrs. The edges may be rounded by filing or chamfered by other methods.NOTE Non-rounded or non-chamfered edges are permissible, if the test result meets the test req
27、uirements.5 Procedure5.1 In general, the test shall be carried out at ambient temperature within the limits of 10 C to 35 C. The test carried out under controlled conditions shall be made at a temperature of 23 C 5 C.5.2 Place the ring cut from the tube over the pins. Subject the ring to strain by m
28、oving the pins away from each other at a specified rate until it fractures.In cases of dispute, the rate shall not exceed 5 mm/s.5.3 Interpretation of the ring tensile test shall be carried out in accordance with the requirements of the relevant product standard. When these requirements are not spec
29、ified, the test piece shall be considered to have passed the test if the expected fracture behaviour was obtained and no other cracks are visible without the use of magnifying aids.6 Test reportA test report shall be provided when so specified in the relevant product standard. In this case, the test
30、 report shall include at least the following information:a) a reference to this International Standard, i.e. ISO 8496;b) identification of the test piece;c) dimensions of the test piece;d) result of the test.2 ISO 2013 All rights reservedBS EN ISO 8496:2013This page deliberately left blankThis page
31、deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Sta
32、ndards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has
33、 been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succee
34、d. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at whe
35、re hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For fu
36、rther information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch wi
37、th standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of
38、your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you w
39、ish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefi
40、t your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or s
41、ome person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced
42、, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
