1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 10380:2012Pipework Corrugated metalhoses and hose assembliesBS EN ISO 10380:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation ofEN IS
2、O 10380:2012. It supersedes BS EN ISO 10380:2003, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e G S E / 4 2 , G a s f i t t i n g s a n d c o n n e c t i o n s including metal hose and hose assemblies.A list of organizations represent
3、ed on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012.ISBN 978 0 580
4、70918 0 ICS 23.040.70 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2012.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN STA
5、NDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10380 October 2012 ICS 23.040.70 Supersedes EN ISO 10380:2003English Version Pipework - Corrugated metal hoses and hose assemblies (ISO 10380:2012) Tuyauteries - Tuyaux et tuyauteries mtalliques flexibles onduleux (ISO 10380:2012) Rohrleitungen - Gewellte
6、 Metallschluche und Metallschlauchleitungen (ISO 10380:2012) This European Standard was approved by CEN on 30 September 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard w
7、ithout any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any oth
8、er language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic,
9、 Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMM
10、ITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10380:2012: EBS EN ISO 10380:2012
11、EN ISO 10380:2012 (E) 3 Foreword This document (EN ISO 10380:2012) has been prepared by Technical Committee CEN/TC 342 “Metal hoses, hose assemblies, bellows and expansion joints“, the secretariat of which is held by SNV, in collaboration with Technical Committee ISO/TC 5 “Ferrous metal pipes and me
12、tallic fittings“. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the latest by April 2013. Attention is drawn to the possibili
13、ty that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 10380:2003. According to the CEN/CENELEC Internal Regulations, the national standards org
14、anisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg
15、, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN ISO 10380:2012ISO 10380:2012(E) ISO 2012 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope 12 Normative references . 13 Terms and definitio
16、ns . 14 Design requirements 44.1 General . 44.2 Nominal sizes, DN . 54.3 Overall length, lO . 64.4 Hose design 64.5 Materials . 64.6 Braiding 74.7 Pressure . 94.8 Temperature 94.9 Corrosion .104.10 Cleanliness 114.11 Electrical conductivity . 114.12 Flow velocity . 114.13 Additional protection 124.1
17、4 Hose joining 144.15 Attachment of end fittings to hose .154.16 Design parameters for corrugated metal hoses and metal hose assemblies 165 Performance requirements and tests 165.1 General .165.2 Leaktightness .175.3 Pressure resistance 175.4 Elongation .185.5 Burst pressure .185.6 Pliability .195.7
18、 Fatigue 215.8 Electrical conductivity .266 Evaluation of conformity .266.1 Declaration of products relating to the conformity assessment method 266.2 General .276.3 Initial type testing 276.4 Subsequent type testing .286.5 Factory production control (FPC) .286.6 Final assessment .307 Installation i
19、nstructions, packaging, designation and marking .317.1 Installation instructions .317.2 Packaging 317.3 Designation .317.4 Marking .32Annex A (normative) Equivalent European material specifications .33Bibliography .36BS EN ISO 10380:2012ISO 10380:2012(E)ForewordISO (the International Organization fo
20、r Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the
21、 right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.Internatio
22、nal Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as
23、 an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO
24、10380 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 342, Metal hoses, hose assemblies, bellows and expansion joints, in collaboration with ISO Technical Committee TC 5, Ferrous metal pipes and metallic fittings, Subcommittee SC 11, Metal hoses and expans
25、ion joints, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). This third edition cancels and replaces the second edition (ISO 10380:2003), which has been technically revised.iv ISO 2012 All rights reservedBS EN ISO 10380:2012ISO 10380:2012(E)Introducti
26、onIt was decided to produce an International Standard under the Vienna Agreement on technical cooperation between ISO and the European Committee for Standardization (CEN) in order to maintain a unique EN ISO document.The major changes in this revision of this International Standard are the following
27、: update of the structure of the International Standard; update of the test and performance requirements to reflect the practice of the industry at the time of publication; introduction of an evaluation of conformity and a system of certification.This International Standard is a base standard for co
28、rrugated metal hoses and hose assemblies for general purpose.Corrugated metal hoses and metal hose assemblies conforming to all aspects of this International Standard are considered to be designed and manufactured to sound engineering practice.The requirements of this International Standard are of i
29、mportance to designers, manufacturers, users, suppliers and importers of corrugated metal hoses.Non-permanent, detachable connections between hoses and fittings are available in the market. Their design is not covered by this International Standard. ISO 2012 All rights reserved vBS EN ISO 10380:2012
30、BS EN ISO 10380:2012Pipework Corrugated metal hoses and hose assemblies1 ScopeThis International Standard specifies the minimum requirements for the design, manufacture, testing and installation of corrugated metal hose and metal hose assemblies.2 Normative referencesThe following referenced documen
31、ts are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 6208, Nickel and nickel alloy plate, sheet and stripISO 9328-7, Steel flat pro
32、ducts for pressure purposes Technical delivery conditions Part 7: Stainless steelsISO 9723, Nickel and nickel alloy barsISO 9724, Nickel and nickel alloy wire and drawing stockISO 13585, Brazing Qualification test of brazers and brazing operators ISO 15614-1, Specification and qualification of weldi
33、ng procedures for metallic materials Welding procedure test Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloysISO 16143-3, Stainless steels for general purposes Part 3: WireEN 287-1, Qualification test of welders Fusion welding Part 1: SteelsEN 1652, Copper and copper
34、alloys - Plate, sheet, strip and circles for general purposesEN 1779, Non-destructive testing Leak testing Criteria for method and technique selectionEN 10028-7, Flat products made of steels for pressure purposes Part 7: Stainless steelsEN 10088-1, Stainless steels Part 1: List of stainless steelsEN
35、 10088-3, Stainless steels Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposesEN 10204, Metallic products Types of inspection documentsEN 13133, Brazing Brazer approval3 Terms and definiti
36、onsFor the purposes of this document, the following terms and definitions apply.3.1corrugated metal hosepressure-tight hose made from tube or from strip, with corrugations, helical or annular to the axis of the hose, made by deforming the metal, its flexibility being obtained by bending the corrugat
37、ionsNOTE 1 Classified by material, DN, PS at 20 C, bend radius and lifetime.NOTE 2 In this International Standard, helical is designated “h” and annular is designated “a”.INTERNATIONAL STANDARD ISO 10380:2012(E) ISO 2012 All rights reserved 1BS EN ISO 10380:2012ISO 10380:2012(E)3.2nominal size DNalp
38、hanumeric designation of size comprising the letters DN followed by a dimensionless whole number which is indirectly related to the physical size, in millimetres, of the bore or the outside diameter of the end connections, and is used as a referenceNOTE 1 This defined number does not represent a mea
39、surable value and cannot be used for calculation purposes except where specified in the relevant standard.NOTE 2 Adapted from ISO 6708.NOTE 3 Adapted from ISO 7369:2004, definition 4.1.5.3.3strandgroup of parallel wires that are woven together to form a single layer of braid3.4braid pitchdistance me
40、asured parallel to the axis of the braid for one complete turn or revolution of a strand3.5braided braidbraid that is manufactured from previously braided strands3.6metal hose assemblyassembly of a corrugated metal hose with its end fittings subjected to internal or external pressureSee Figure 1.2 I
41、SO 2012 All rights reservedBS EN ISO 10380:2012ISO 10380:2012(E)lOlLKey1 end fitting2 ferrule3 corrugated metal hose/braidDiinternal diameterDOoutside diameterlLactive live lengthlOoverall lengthq pitch of the hose profileFigure 1 Metal hose assembly3.7nominal pressurePNnumerical designation which i
42、s a convenient rounded number for reference purposesISO 7369:2004, definition 3.3NOTE 1 This defined number is a dimensionless number indirectly related to a pressure value in bar(s).NOTE 2 Adapted from ISO 7268. See EN 1333.3.8maximum allowable pressurePSpSmaximum pressure at the operating temperat
43、ure for which the hose assembly is designed, as specified by the manufacturer3.9operating temperatureTSextreme operating temperature, positive or negative, for which the hose assembly is designed ISO 2012 All rights reserved 3BS EN ISO 10380:2012ISO 10380:2012(E)3.10active live lengthlLcorrugated me
44、tal hose length to be taken into account for the design of the hose assemblies subjected to repeated movements3.11type testinggroup of tests to be performed in order to verify that the performance level of the product meets the requirements of a standard3.12qualified proceduremanufacturing and desig
45、n process demonstrated by tests and described in detail in process instructions for the specific manufacturing or design NOTE For products subject to specific quality surveillance systems, such procedures can be qualified by the required authorities or person.3.13third-party conformity assessment ac
46、tivityconformity valuation activity that is performed by a person or body independent of the person or organization who/which provides the object, and independent of user interests in that objectNOTE 1 Criteria for the independence of conformity assessment bodies and accreditation bodies are provide
47、d in the International Standards and Guides applicable to their activities.NOTE 2 The first-, second- and third-party descriptors used to characterize conformity assessment activities with respect to a given object are not to be confused with the legal identification of the relevant parties to a con
48、tract.3.14certificationthird-party attestation related to products, processes, systems or personsNOTE 1 Certification of a management system is sometimes also called registration.NOTE 2 Certification is applicable to all objects of conformity assessment except for conformity assessment bodies themse
49、lves, to which accreditation is applicable.3.15test pressurePTdifferential pressure to which the hose assembly or the component is subjected during a test at ambient temperatureNOTE Adapted from ISO 7369:2004, definition 3.8.3.16manufacturerproducer of corrugated metal hose or producer of corrugated metal hose and metal hose assemblies3.17assemblerfabricator of metal hose assemblies with corrugated metal hose purchased from manufacturers4 Design requirements4.1 GeneralCorrugated metal hoses, braided or unbraided, and t
