1、BS EN ISO 11469:2016Plastics Genericidentification and markingof plastics products (ISO11469:2016)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 11469:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 11469:2016
2、. It supersedes BS EN ISO 11469:2000 which iswithdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/10, Terminology for rubbers and plastics.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not
3、 purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 86924 2 ICS 83.080.01; 83.140.01 Compliance with a British Standard cannot confer immunity f
4、rom legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11469 October 2016 ICS 83
5、.080.01 Supersedes EN ISO 11469:2000English Version Plastics - Generic identification and marking of plastics products (ISO 11469:2016) Plastiques - Identification gnrique et marquage des produits en matire plastique (ISO 11469:2016) Kunststoffe - Sortenspezifische Identifizierung und Kennzeichnung
6、von Kunststoff-Formteilen (ISO 11469:2016) This European Standard was approved by CEN on 17 September 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterat
7、ion. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made b
8、y translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
9、 Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDI
10、ZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11469:2016 EBS EN ISO 11469:2016EN ISO 1
11、1469:2016 (E) 3 European foreword This document (EN ISO 11469:2016) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national st
12、andard, either by publication of an identical text or by endorsement, at the latest by April 2017, and conflicting national standards shall be withdrawn at the latest by April 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.
13、CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 11469:2000. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard
14、: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
15、 Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 11469:2016 has been approved by CEN as EN ISO 11469:2016 without any modification. BS EN ISO 11469:2016ISO 11469:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols and abbre
16、viated terms . 25 Requirements 25.1 Marking system 25.1.1 Marking of products 25.1.2 Single-constituent products . 25.1.3 Polymer blends or alloys . 25.1.4 Compositions with special additives 35.2 Method of marking 4 ISO 2016 All rights reserved iiiContents PageBS EN ISO 11469:2016ISO 11469:2016(E)F
17、orewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a tec
18、hnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o
19、f electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document
20、 was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such p
21、atent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does no
22、t constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.o
23、rg/iso/foreword.html.The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 1, Terminology.This third edition cancels and replaces the second edition (ISO 11469:2000), which has been technically revised with the following changes: the definition of “plastics products” ha
24、s been modified; the marking of recyclates has been included.iv ISO 2016 All rights reservedBS EN ISO 11469:2016INTERNATIONAL STANDARD ISO 11469:2016(E)Plastics Generic identification and marking of plastics products1 ScopeThis International Standard specifies a system of uniform marking of products
25、 that have been fabricated from plastics materials. Provision for the process or processes to be used for marking is outside the scope of this International Standard.NOTE 1 Precise details of the marking, e.g. the minimum size of the item to be marked, the size of the lettering, the appropriate loca
26、tion of the marking, are subject to agreement between the manufacturer and the user.The marking system is intended to help identify plastics products for subsequent decisions concerning handling, waste recovery or disposal.Generic identification of the plastics is provided by the symbols and abbrevi
27、ated terms given in ISO 1043-1, ISO 1043-2, ISO 1043-3 and ISO 1043-4.NOTE 2 If more detailed information for material identification is needed, additional marking of plastics products can be applied as defined in the appropriate product standard.This International Standard is not intended to suppla
28、nt, replace or in any way interfere with the requirements for labelling specified in product standards or legislation.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only
29、the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 472, Plastics VocabularyISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristicsISO 1043-2, Plastics Symbols and
30、abbreviated terms Part 2: Fillers and reinforcing materialsISO 1043-3, Plastics Symbols and abbreviated terms Part 3: PlasticizersISO 1043-4, Plastics Symbols and abbreviated terms Part 4: Flame retardants3 Terms and definitionsFor the purposes of this document, the terms and definitions given in IS
31、O 472 and the following apply.3.1abbreviated termterm resulting from the omission of any part of a term while designating the same conceptSOURCE: ISO 1043-1:2011, 3.13.2plastics productsarticles or stocks shapes of plastic materials for any type of application ISO 2016 All rights reserved 1BS EN ISO
32、 11469:2016ISO 11469:2016(E)4 Symbols and abbreviated termsThe symbols and abbreviated terms given in ISO 1043-1, ISO 1043-2, ISO 1043-3 and ISO 1043-4 shall be used for this International Standard. If an appropriate symbol or abbreviated term is not included in ISO 1043 (all parts), such a symbol o
33、r abbreviated term from any available national or international standard may be used. Based on the rule of symbol “REC” for polymer in ISO 1043-1, a similar rule is applied to a product with two or more components when it is regarded as a single recyclate.5 Requirements5.1 Marking system5.1.1 Markin
34、g of productsIf plastics products are marked with the identification of the plastic materials, they shall be marked at some place on the surface with the appropriate standard symbol(s) or abbreviated term(s) set between the punctuation marks “” and “” and “ABSABSABS(REC)ABS(RECx)PC+ABSPC+ABS(REC30)P
35、P-MD30PS-HI-GF20PA66-(GF25+MD15)PA66-(GF+MD)40UP-(MD50+GF25)UP-(MD+GF)75PVC-P(DBP)PA66-(GF25+MD15)FR(52)PA66-(GF+MD)40FR(52)PA66-(GF25+MD15)FR(52)(REC30)PA66-(GF+MD)40FR(52) (REC30)PVC,PUR,ABS5.2 Method of markingThe marking shall be made during moulding by having the appropriate symbol included in
36、the mould design, or by embossing, or by melt imprinting, or by other legible and indelible marking of the polymer.NOTE 1 Precise details of the marking, e.g. the minimum size of the item to be marked, the size of the lettering, the appropriate location of the marking, are subject to agreement betwe
37、en the manufacturer and the user.NOTE 2 If space for marking is not able to be secured, modification or omitting of marking is subject to agreement between the manufacturer and the user.4 ISO 2016 All rights reservedBS EN ISO 11469:2016This page deliberately left blankThis page deliberately left bla
38、nkBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (B
39、SI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open cons
40、ultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting
41、 our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standa
42、rds from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the
43、information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distr
44、ibute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for p
45、ersonal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard
46、 copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the d
47、ocument on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make usin
48、g standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up
49、 to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benef
