1、BS EN ISO17635:2010ICS 25.160.40NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDNon-destructivetesting of welds General rules formetallic materials (ISO17635:2010)Copyright European Committee for Standardization Provided by IHS under license with CENNot for Resa
2、leNo reproduction or networking permitted without license from IHS-,-,-This British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 March2010 BSI 2010ISBN 978 0 580 55935 8Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 17635:2010Natio
3、nal forewordThis British Standard is the UK implementation of EN ISO 17635:2010.It supersedes BS EN 12062:1998 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee WEE/46, Non-destructive testing.A list of organizations represented on this committee can be o
4、btained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Copyright European Committee for Standardizatio
5、n Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 17635 March 2010 ICS 25.160.40 Supersedes EN 12062:1997English Version Non-destructive testing of welds - General rules
6、for metallic materials (ISO 17635:2010) Contrle non destructif des assemblages souds - Rgles gnrales pour les matriaux mtalliques (ISO 17635:2010)Zerstrungsfreie Prfung von Schweiverbindungen - Allgemeine Regeln fr metallische Werkstoffe (ISO 17635:2010) This European Standard was approved by CEN on
7、 6 February 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards ma
8、y be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the C
9、EN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
10、 Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploit
11、ation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 17635:2010: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 17635:2010E
12、N ISO 17635:2010 (E) 3 Foreword This document (EN ISO 17635:2010) has been prepared by Technical Committee CEN/TC 121 “Welding”, the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 44 “Welding and allied processes“. This European Standard shall be given the stat
13、us of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2010, and conflicting national standards shall be withdrawn at the latest by September 2010. Attention is drawn to the possibility that some of the elements of this document may be the
14、 subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12062:1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement
15、 this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzer
16、land and the United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 17635:2010ISO 17635:2010(E) ISO 2010 All rights reserved iiiContents Page Foreword iv 1 Sco
17、pe1 2 Normative references1 3 Terms and definitions .2 4 Abbreviated terms.3 5 Limitations .3 5.1 Stage of manufacture3 5.2 Extent of testing 3 5.3 Materials .3 6 Personnel qualification.4 7 Testing organization .4 8 Documentation 4 8.1 Documentation prior to testing4 8.2 Documentation after testing
18、.4 9 Selection of testing method .5 9.1 General .5 9.2 Butt- and T-joints with full penetration .5 9.3 Butt- and T-joints without full penetration and fillet welds.6 10 Performance of testing .6 10.1 Determination of standard to be applied 6 10.2 Conditions for testing .6 10.3 Time of testing.7 10.4
19、 Non-acceptable indications7 Annex A (normative) Rules and standards to be applied.8 Annex B (informative) Graph of standard context.12 Annex C (informative) Non-acceptable indications.16 Bibliography17 Copyright European Committee for Standardization Provided by IHS under license with CENNot for Re
20、saleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 17635:2010ISO 17635:2010(E) iv ISO 2010 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of prep
21、aring International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in
22、liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task
23、of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention
24、is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 17635 was prepared by the European Committee for Standardization (CEN) Technical Committee TC 121, Welding,
25、 in collaboration with Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 5, Testing and inspection of welds, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). This second edition cancels and replaces the first edition (ISO 17
26、635:2003), which has been technically revised. Requests for official interpretations of any aspect of this International Standard should be directed to the Secretariat of ISO/TC 44/SC 5 via your national standards body. A complete listing of these bodies can be found at www.iso.org. Copyright Europe
27、an Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 17635:2010INTERNATIONAL STANDARD ISO 17635:2010(E) ISO 2010 All rights reserved 1Non-destructive testing of welds General rules for meta
28、llic materials 1 Scope This International Standard gives guidelines for the choice of non-destructive testing (NDT) methods for welds and evaluation of the results for quality control purposes, based on quality requirements, material, weld thickness, welding process, and extent of testing. This Inte
29、rnational Standard also specifies general rules and standards to be applied to the different types of testing, for either the methodology or the acceptance level for metallic materials. Acceptance levels cannot be a direct interpretation of the quality levels defined in ISO 5817 or ISO 10042. They a
30、re linked to the overall quality of the produced batch of welds. Requirements for acceptance levels for NDT comply with quality levels stated in ISO 5817 or ISO 10042 (moderate, intermediate, stringent) only on a general basis and not in detail for each indication. Annex A gives correlations between
31、 quality, NDT and acceptance level standards. Annex B gives an overview of the standards linked to quality levels, acceptance levels, and NDT methods. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edit
32、ion cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3452-1, Non-destructive testing Penetrant testing Part 1: General principles ISO 5817, Welding Fusion-welded joints in steel, nickel, titanium and their alloys (beam weldi
33、ng excluded) Quality levels for imperfections ISO 9712, Non-destructive testing Qualification and certification of personnel ISO 10042, Welding Arc-welded joints in aluminium and its alloys Quality levels for imperfections ISO 10675-1, Non-destructive testing of welds Acceptance levels for radiograp
34、hic testing Part 1: Steel, nickel, titanium and their alloys ISO 10675-2, Non-destructive testing of welds Acceptance levels for radiographic testing Part 2: Aluminium and its alloys ISO 108631), Welding Use of time-of-flight diffraction technique (TOFD) for testing of welds ISO 11666, Non-destructi
35、ve testing of welds Ultrasonic testing of welded joints Acceptance levels 1) To be published. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 17635:2010ISO 17635:2010(E
36、) 2 ISO 2010 All rights reservedISO 17636, Non-destructive testing of welds Radiographic testing of fusion-welded joints ISO 17637, Non-destructive testing of welds Visual testing of fusion-welded joints ISO 17638, Non-destructive testing of welds Magnetic particle testing ISO 17640, Non-destructive
37、 testing of welds Ultrasonic testing Techniques, testing levels, and assessment ISO 17643, Non-destructive testing of welds Eddy current testing of welds by complex-plane analysis ISO 19232-5, Non-destructive testing Image quality of radiographs Part 5: Image quality indicators (duplex wire type) De
38、termination of image unsharpness value ISO 23277, Non-destructive testing of welds Penetrant testing of welds Acceptance levels ISO 23278, Non-destructive testing of welds Magnetic particle testing of welds Acceptance levels ISO 23279, Non-destructive testing of welds Ultrasonic testing Characteriza
39、tion of indications in welds EN 473, Non-destructive testing Qualification and certification of NDT personnel General principles EN 13068-3, Non-destructive testing Radioscopic testing Part 3: General principles of radioscopic testing of metallic materials by X- and gamma rays EN 14784-2, Non-destru
40、ctive testing Industrial computed radiography with storage phosphor imaging plates Part 2: General principles for testing of metallic materials using X-rays and gamma rays EN 15617, Non-destructive testing of welds Time-of-flight diffraction technique (TOFD) Acceptance levels 3 Terms and definitions
41、 For the purposes of this document, the following terms and definitions apply. 3.1 testing level degree of thoroughness and selection of parameter settings with which a testing method is applied ISO/TR 25901:20072, 2.376 NOTE Different levels correspond to different sensitivities and/or probabilitie
42、s of detection. The selection of testing levels is normally related to the quality requirements. 3.2 testing organization internal or external organization carrying out non-destructive testing NOTE Adapted from ISO/TR 25901:20072, 2.377. 3.3 indication non-destructive testing representation or signa
43、l from a discontinuity in the format allowed by the non-destructive testing method used NOTE Adapted from ISO/TR 25901:20072, 2.193. 3.4 internal discontinuity non-destructive testing of welds discontinuity that is not open to a surface or not directly accessible Copyright European Committee for Sta
44、ndardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 17635:2010ISO 17635:2010(E) ISO 2010 All rights reserved 33.5 quality level description of the qualities of a weld on the basis of type, size, and amount of
45、 selected imperfections ISO/TR 25901:20072, 2.294 3.6 inspection lot non-destructive testing of welds group of welds which is expected to show a uniform quality NOTE 1 Group members can be a part of a weld, a full weld or several welds. NOTE 2 The uniform quality can be due to welding procedure appl
46、ied, material, type of joint, welder, environmental conditions during execution, time period or other items affecting the quality. 4 Abbreviated terms For the purposes of this International Standard, the abbreviations given in Table 1 apply. Table 1 Abbreviations Testing method Abbreviation Eddy cur
47、rent testing ET Magnetic particle testing MT Penetrant testing PT Radiographic testing RT Ultrasonic testing UT Visual testing VT 5 Limitations 5.1 Stage of manufacture This International Standard has been prepared for the testing of completed welds (see 10.3). Testing of parent materials prior to w
48、elding or between welding sequences is not covered by this International Standard. It is, however, recommended that such testing be performed in accordance with the reference standards for methods and acceptance levels. 5.2 Extent of testing The extent of testing shall be given in an application standard or defined in a specification. 5.3 Materials This International Standard includes requirements for testing of fusion welds in the following materials, their alloys and their combinations: a) steel; b) aluminium; c) copper; Co
