GOST 28941 8-1991 Flare stud elbow fittings Construction《有管扩口的拧入式弯头的管路连接 结构》.pdf

相关资源

GOST 28941 11-1991 Flare cross straight fittings Construction《有管扩口的四通接头的管路连接 结构》.pdf

GOST 28941 12-1991 Flare fittings Flared conplings Construction《有管扩口的管路连接 管的扩口端 结构》.pdf

GOST 28941 13-1991 Flare fittings Reducing conplings Construction《有管扩口的管路连接 联通管接头 结构》.pdf

GOST 28941 18-1991 Flare fittings Bulkhead conplings Construction《有管扩口的管路连接 隔房间的接头 结构》.pdf

GOST 28941 19-1991 Flare fittings Unequal elbows Construction《有管扩口的管路连接 联通弯头 结构》.pdf

GOST 28941 2-1991 Flare fittings with reducing conplings Construction《有管扩口的转接口的管路连接 结构》.pdf

GOST 28941 25-1991 Flare fittings Snugle plugs Construction《有管扩口的管路连接 无孔丝堵 结构》.pdf

GOST 28941 26-1991 Flare conplings Union nuts Construction《有管扩口的管路连接 活接螺母 结构》.pdf

GOST 28941 27-1991 Flare fittings Sleeves Construction《有管扩口的管路连接 肉丝 结构》.pdf

GOST 28941 28-1991 Flare fittings O-rings Construction《有管扩口的管路连接 密封圈 结构》.pdf

猜你喜欢

FORD WSS-M4D952-A2-2006 THERMOPLASTIC POLYOLEFIN ELASTOMER (TEO) UNFILLED MOLDING COMPOUND UV STABILIZED MOLD-IN-COLOR PARTIALLY PAINTED EXTERIOR TO BE USED WITH FORD WSS-M99P1111.pdf

FORD WSS-M4D952-A3-2006 THERMOPLASTIC POLYOLEFIN ELASTOMER (TEO) UNFILLED MOLDING COMPOUND FULLY PAINTED EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用完全涂漆的不填充热塑性聚烯径(TEO)成型料.pdf

FORD WSS-M4D953-A1-2006 POLYVINYL CHLORIDE (PVC) ALLOY FLEXIBLE 89 DUROMETER A HARDNESS MOLDING COMPOUND EXTERIOR PAINTABLE TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用可印刷硬度为89 A的聚.pdf

FORD WSS-M4D953-A2-2006 POLYVINYL CHLORIDE (PVC) ALLOY FLEXIBLE 76 DUROMETER A HARDNESS MOLDING COMPOUND EXTERIOR PAINTABLE TO BE USED WITH FORD WSS-M99P1111-A (Shown on WSS-M4D9.pdf

FORD WSS-M4D954-A-2015 THERMOPLASTIC POLYOLEFIN ELASTOMER (TEO) 30% MINERAL FILLED COLOR PIGMENTED MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M4D955-A-2012 POLYETHYLENE (PE) HIGH DENSITY MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《高密度聚乙烯(PE)模塑材料 与福特WSS-M99P1111-A 一起使用[使用 福特WRS-M4D955-B]》.pdf

FORD WSS-M4D955-B-2011 POLYETHYLENE (PE) HIGH DENSITY MOLDING COMPOUND NON VISIBLE EXTERIOR UNDERBODY TO BE USED WITH FORD WSS-M99P1111-A 《外部 地面不可视的高密度聚乙烯(PE)模塑材料 与福特WSS-M99P11.pdf

FORD WSS-M4D959-A-2011 POLYPROPYLENE (PP) HOMOPOLYMER 20% CALCIUM CARBONATE FILLED HEAT STABILIZED IMPACT MODIFIED MOLDING COMPOUND 25% MIN POST CONSUMER CONTENT TO BE USED WITH F.pdf

FORD WSS-M4D959-A2-2011 POLYPROPYLENE (PP) HOMOPOLYMER 30% CALCIUM CARBONATE FILLED HEAT STABILIZED 25% MIN POST CONSUMER CONTENT TO BE USED WITH FORD WSS-M99P1111-A 《30%碳酸钙填充热稳定.pdf