1、 (IEC 62208:2011, IDT) , ()INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION(ISC)IEC 622082013, 1.092 . 1.22009 . , - . , , -, 1 - - ()2 (-)3 , (- 27 2013 . 59-) : ( 3166) 00497 ( 3166) 00497 AMBYKGRUTJUZ 4 11 2014 . 113- IEC 622082013 - 1 2015 .5 IEC 62208:2011 Empty enclosuresfor
2、 low-voltage switchgear and controlgear assemblies General requirements ( - . ). -. : - - 1.52001 (- 3.6). SC 17D - IEC/C 17 - (IEC). (en). - . (IDT)6 II IEC 622082013 - , - . () - . , , 2014 -, III IEC 6220820131 12 13 24 .35.36 .36.1 .36.2 .36.3 .37 .47.1 .47.2 .47.3 57.4 .58 58.1 .58.2 .58.3 .58.
3、4 58.5 68.6 .68.7 ( I)68.8 ( IP)69 69.1 .69.2 69.3 .79.4 .79.5.79.6 89.7 ( IK) 89.8 ( IP)89.9 .99.10 119.11 119.12 () .119.13 129.14 .13 () .14 15IV IEC 622082013 Enclosures for low-voltage switchgear and controlgear assemblies. General requirements 201501011 , - . , , , - (, IEC 61439) 1000 1500 .
4、1 . 2 () Type NEMA 250. NEMA Enclosure Type , , -, , . IP IEC Type, . , - (, IEC 60670). , , . 3 .2 . - . ( ).IEC 60068-2-2:2007 Environmental testing Part 2-2: Tests Test B: Dry heat ( - . 2-2. . : )IEC 60068-2-11:1981 Basic environmental testing procedures Part 2-11: Tests Test Ka: Salt mist( . 2-
5、11. . Ka: )IEC 60068-2-30:2005 Environmental testing Part 2-30: Tests Test Db: Damp heat, cyclic(12 h + 12 h cycle) ( . 2-30. . Db: , ( 12+12)IEC 60085:2007 Electrical insulation Thermal evaluation and designation ( -. )1 IEC 622082013 IEC 60529:1989 Degrees of protection provided by enclosures (IP
6、Code)1)( , - (IP Code)IEC 60695-2-10:2013 Fire hazard testing Part 2-10: Glowing/hot-wire based test methods Glow-wire apparatus and common test procedure ( . 2-10. - / . - )IEC 60695-2-11:2000 Fire hazard testing Part 2-11: Glowing/hot-wire based test methods Glow-wire flammability test methods for
7、 end-products ( . 2-11. / . )IEC 61439-1:2011 Low-voltage switchgear and controlgear assemblies Part 1: General rules (- . 1. )IEC 62262:2002 Degrees of protection provided by enclosures for electrical equipment against externalmechanical impacts (IK Code) ( , -, ( IK)ISO 178:2010 Plastics Determina
8、tion of flexural properties (. - )ISO 179 ( ) Plastics Determination of Charpy impact properties (. - )ISO 2409:2013 Paints and varnishes Cross-cut test ( . - )ISO 4628-3:2003 Paints and varnishes Evaluation of degradation of coatings Designation ofquantity and size of defects, and of intensity of u
9、niform changes in appearance Part 3: Assessment ofdegree of rusting ( . . - . 3. -)ISO 4892-2:2013 Plastics Methods of exposure to laboratory light sources Part 2: Xenon-arclamps (. . 2. - )ISO 11469:2000 Plastics Generic identification and marking of plastic products (. )3 :3.1 (empty enclosure): ,
10、 -, -, . 1 -. 2 , , .3.2 (protected space): - , , , .3.3 (cover): .3.4 (door): .3.5 (mounting plate): , - .3.6 (cable gland plate): , , .3.7 (removable cover): , - .1) 2.1 (2001) IEC 60529 (1989) Amd 1 (1999).2 IEC 622082013 .3.8 (enclosure manufacturer): , - .4 :) :- ;- ;- ;b) :- ;- ;- ;- ;c) :- ;-
11、 ;d) :- IP IEC 60529;- IK IEC 62262;e) ( , ).5 , , , - . , , ( EM) IEC 61000-5-7.6 6.1 .6.2 , . :- , ;- . . 9.3 . , , ISO 11469. , ( II), IEC 60417-5172 - .6.3 6.3.1 , - , (. 4) , , , - :- (. 6.3.2);- (. 6.3.3);- (. 6.3.4);- (. 6.3.5);3 IEC 622082013- (. 6.3.6);- (. 7);- ;- , ;- , ;- ( IP IK, . 8.7 8.8)., , - . - (, , )
