HOLDEN HN 2122-2003 Adhesive Tape - Abrasion Resistant《耐磨胶布》.pdf

上传人:outsidejudge265 文档编号:782678 上传时间:2019-01-24 格式:PDF 页数:4 大小:36.45KB
下载 相关 举报
HOLDEN HN 2122-2003 Adhesive Tape - Abrasion Resistant《耐磨胶布》.pdf_第1页
第1页 / 共4页
HOLDEN HN 2122-2003 Adhesive Tape - Abrasion Resistant《耐磨胶布》.pdf_第2页
第2页 / 共4页
HOLDEN HN 2122-2003 Adhesive Tape - Abrasion Resistant《耐磨胶布》.pdf_第3页
第3页 / 共4页
HOLDEN HN 2122-2003 Adhesive Tape - Abrasion Resistant《耐磨胶布》.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、A.C.N. 006 893 232 Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2122 1 of 4 December 1995 February, 2003 NAME: ADHESIVE TAPE - ABRASION RESISTANT THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RES

2、PONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:CentralLaboratoryStandardForms MaterialSpecificationMatspec.doc 1. SCOPE This specification covers a thermoplastic, polyester elastomer film precoated with an acrylic pressure sensitive adhesive protected with a silicone release li

3、ner. This film is designed to provide surface protection against scratches, stone chips, chafing, and mechanical wear. This film has a maximum service temperature of 135 oC. Both film and adhesive are transparent. This material can also serve as a stencil for etching information on glass. 2. REFEREN

4、CED STANDARDS ASTM D882 ASTM D1938 GM9505P HN 1000 PSTC1 SAE J400 3. PROPERTIES 3.1 Physical Properties See Table 1 TABLE 1 Properties Values Color Clear Film thickness 0.075 mm Adhesive thickness 0.05 mm Total thickness 0.13 + 0.02 mm 3.2 Film Performance All tests shall be performed at ambient con

5、ditions, 22 3 oC and 55 5% RH, unless otherwise indicated. 3.2.1 Tensile Strength (ASTM D882) The film shall exhibit a tensile strength of 10 MPa 10% when evaluated per ASTM D882, Method A, at a rate of 300 mm/minute. The jaw separation shall be 102 mm. A.C.N. 006 893 232 Holden Limited Engineering

6、Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2122 2 of 4 December 1995 February, 2003 NAME: ADHESIVE TAPE - ABRASION RESISTANT THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS

7、 STILL VALID. FORM : I:CentralLaboratoryStandardForms MaterialSpecificationMatspec.doc 3. PROPERTIES (continued) 3.2 Film Performance (continued) 3.2.2 Elongation (ASTM D882) The film shall exhibit an elongation at break of 130 10% when tested as described in 3.2.1. 3.2.3 Tear Strength (ASTM D1938)

8、The film shall exhibit a tear strength of 1.8 0.4kg. 3.2.4 Taber Abrasion (SAE J1847) There shall be a maximum of 0.1 g mass loss when tested per SAE J1847, 1000 cycles, 1kg load, H18 abrading wheel. 3.2.5 Gravelometer (SAE J400) The film shall exhibit a rating of 10 or better when tested according

9、to SAE J400, using a temperature of 30 2 C. 3.3 Adhesion Performance 3.3.1 Peel Adhesion (PSTC1) When bonded to stainless steel, the pressure sensitive adhesive backed film must maintain a peel strength of 740 N/m 10%. This bond strength must be maintained following a minimum of 72 h at ambient cond

10、itions and all environmental exposures (See 3.4). 3.3.2 Test Procedure Bond 150 mm of a 25 x 300 mm sample of the adhesive backed film to the stainless steel. Allow the assembly to dwell 72 h at ambient conditions prior to exposure. Following exposure, fold back the extended (unbonded) portion of th

11、e sample to a 180o angle. Peel the sample at a rate of 300 mm/minute using an Instron, or equivalent, constant rate of extension (CRE) machine. A.C.N. 006 893 232 Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2122 3 of 4 December 1995 February, 2003

12、NAME: ADHESIVE TAPE - ABRASION RESISTANT THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:CentralLaboratoryStandardForms MaterialSpecificationMatspec.doc 3. PROPERTIES (continue

13、d) 3.4 Environmental Exposures Samples shall be allowed a dwell time of 24 h at ambient conditions following exposure and prior to testing. 3.4.1 Humidity Ageing The samples shall be exposed for 168 h at 38 2 C and 95 5% RH. 3.4.2 Heat Ageing The samples shall be exposed for 168 h at 93 2 C. 3.4.3.

14、Cycle Test The samples shall be exposed to GM9505P, Cycle F. 3.5 Petrol Resistance After 30 minutes immersion in lead free petrol there shall be no change in the transparency of the film. 3.6 Rubber Soil Resistance No discolouration. Test Method: Place a 25 mm x 25 mm piece of EPDM weatherstrip on a

15、 panel with film adhered to it. A 3 kg weight is placed on the EPDM and the assembly is heated at 100 oC for 24 hours. 3.7 Window Glass Etchant When tape cut as a stencil is applied to glass, the tape and adhesive must be fully resistant to the glass etchant. Test to be performed at 25 5 C and a tes

16、t period of 30 minutes. A.C.N. 006 893 232 Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2122 4 of 4 December 1995 February, 2003 NAME: ADHESIVE TAPE - ABRASION RESISTANT THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODU

17、CTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:CentralLaboratoryStandardForms MaterialSpecificationMatspec.doc 4. APPROVAL, INSPECTION AND REJECTION Refer HN 1000, Clauses A and C. 5. HAZARDOUS MATERIALS Refer HN 1000, Clause H. 6. RESTRICTED CHEMICALS Refer HN 1000, Clause J. 7. APPROVED SUPPLIERS AND MATERIALS APPROVED SUPPLIER APPROVED MATERIAL 3M Company E9217 8. REVISIONS July, 1998 - Glass Etchant Clause Added - Hazardous Materials and Restricted Chemicals Clauses Added. February, 2003 - Section 7 added. Prepared by: M. Franke

展开阅读全文
相关资源
猜你喜欢
  • CNS 5914-1986 Non-sparking Beryllium Copper Alloy Tools - Cutting Pliers《防爆用铍铜合金钢丝钳》.pdf CNS 5914-1986 Non-sparking Beryllium Copper Alloy Tools - Cutting Pliers《防爆用铍铜合金钢丝钳》.pdf
  • CNS 5915-1986 Non-sparking Beryllium Copper Alloy Tools - Picks《防爆用铍铜合金十字镐》.pdf CNS 5915-1986 Non-sparking Beryllium Copper Alloy Tools - Picks《防爆用铍铜合金十字镐》.pdf
  • CNS 5916-2001 Method of test for residual antibiotic substances in food《食品中抗生物质残留检验法》.pdf CNS 5916-2001 Method of test for residual antibiotic substances in food《食品中抗生物质残留检验法》.pdf
  • CNS 5917-1999 Method of test for tobacco andtobacco products - Atmosphere for conditioning and testing《烟叶及烟制品检验法-试验场所之标准条件》.pdf CNS 5917-1999 Method of test for tobacco andtobacco products - Atmosphere for conditioning and testing《烟叶及烟制品检验法-试验场所之标准条件》.pdf
  • CNS 5918-1985 Methods of Test for Tobacco and Tobacco Products Determination of Alkaloids in Tobacco (Spectrophometric Method)《烟叶及烟制品检验法–植物碱之测定(光谱测定法)》.pdf CNS 5918-1985 Methods of Test for Tobacco and Tobacco Products Determination of Alkaloids in Tobacco (Spectrophometric Method)《烟叶及烟制品检验法–植物碱之测定(光谱测定法)》.pdf
  • CNS 5919-1985 Method of Test for Tobacco and Tobacco Products Determination of Alkaloids in Cigarette Smoke Condensates - Spectrophotometric Method《烟叶及烟制品检验法–烟流凝缩物内植物碱之测定(光谱测定法)》.pdf CNS 5919-1985 Method of Test for Tobacco and Tobacco Products Determination of Alkaloids in Cigarette Smoke Condensates - Spectrophotometric Method《烟叶及烟制品检验法–烟流凝缩物内植物碱之测定(光谱测定法)》.pdf
  • CNS 5920-1980 Methods of Test for Tobacco and Tobacco Products Determination of Alkaloid Retention by Filters of Cigarettes《烟叶及烟制品检验法–遗留于卷烟滤嘴内植物碱之测定》.pdf CNS 5920-1980 Methods of Test for Tobacco and Tobacco Products Determination of Alkaloid Retention by Filters of Cigarettes《烟叶及烟制品检验法–遗留于卷烟滤嘴内植物碱之测定》.pdf
  • CNS 5921-1985 Method of Test for Tobacco and Tobacco Products Expression of Analytical Test Results《烟叶及烟制品检验法–分析结果之表示法》.pdf CNS 5921-1985 Method of Test for Tobacco and Tobacco Products Expression of Analytical Test Results《烟叶及烟制品检验法–分析结果之表示法》.pdf
  • CNS 5922-1980 Methods of Test for Tobacco and Tobacco Products Determination of Retention of Coloured Part of Smoke Comdensate by Cigarette Filters-Direct Spectrophotometric Method.pdf CNS 5922-1980 Methods of Test for Tobacco and Tobacco Products Determination of Retention of Coloured Part of Smoke Comdensate by Cigarette Filters-Direct Spectrophotometric Method.pdf
  • 相关搜索
    资源标签

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1