NAVY MIL-H-24580 (2)-1985 HOSE ASSEMBLIES SYNTHETIC RUBBER NONCOLLAPSIBLE FIRE FIGHTING《合成橡胶不可折叠消防管道组装》.pdf

上传人:postpastor181 文档编号:979483 上传时间:2019-03-13 格式:PDF 页数:4 大小:157.86KB
下载 相关 举报
NAVY MIL-H-24580 (2)-1985 HOSE ASSEMBLIES SYNTHETIC RUBBER NONCOLLAPSIBLE FIRE FIGHTING《合成橡胶不可折叠消防管道组装》.pdf_第1页
第1页 / 共4页
NAVY MIL-H-24580 (2)-1985 HOSE ASSEMBLIES SYNTHETIC RUBBER NONCOLLAPSIBLE FIRE FIGHTING《合成橡胶不可折叠消防管道组装》.pdf_第2页
第2页 / 共4页
NAVY MIL-H-24580 (2)-1985 HOSE ASSEMBLIES SYNTHETIC RUBBER NONCOLLAPSIBLE FIRE FIGHTING《合成橡胶不可折叠消防管道组装》.pdf_第3页
第3页 / 共4页
NAVY MIL-H-24580 (2)-1985 HOSE ASSEMBLIES SYNTHETIC RUBBER NONCOLLAPSIBLE FIRE FIGHTING《合成橡胶不可折叠消防管道组装》.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、I I i 1 1- 1 # I- MIL-H-ZV580 (2) 92 - 7777706 0232732 2 - .M%L-H-24580( SH) AMENDMENT 2 21 May 1985 SUPERSEDING AMENDMENT 1 15 May 1981 -.- - MILITARY SPECIFICATION HOSE ASSEMBLIES, SYNTHETIC RUBBER, NONCOLLAPSIBLE, FIRE FIGHTING This amendment forms a part of Military Specification MIL-H-245SO(SH)

2、 dated 25 September 1978 and is approved for use by the Naval Sea Systems Command, Department of the Navy and is available for use by all Depart- ments and Agencies of the Department of Defense. PAGE 1 * 2.1: Delete and substitute: . “2.1 Government documents. - - - - - “2.1.1 Specifications and sta

3、ndards. Unless otherwise speciEied the following specifications and standards of the issue listed in that issue of the - Department of Defense Index of SpecificatLons and Standards (DODISC) specified in the solicitation, form a part of this specification to the extent specified herein. SPECIFICATION

4、S - MILITARY MIL-P-775 I - Packaging of Hose, Hose Assemblies, Rubber, Plastic, Fabric, or Metal (including tubing), and Fittings, Nozzles and Strainers. MIL-S-23190 - Straps, Clamps and Mounting Hardware, Plastic for Cable Harness Tying and Support. STANDARDS FEDERAL FED-STD-H28/10 - Screw-Thread S

5、tandards for Federal Services, Section 10 American National Hose Coupling and Fire Hose Coupiing Threads.“ FED-STD-162 - Hose, Rubber, Visual Inspection Guide for. -. . - -. . PSC 4210 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-29580 (2) 9

6、2 W 777790b 0232733 9 W MIL-H-24580(SH) AMENDMENT 2 1 * c STANDARDS - Continued MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes.“ Insert “Beneficial comments“ at bottom of page: beneficial comments (recommendations, addirions, deletions) and any pertinent data whic

7、h may be of use in improving this document should be addressed to: Commander, Naval Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by le

8、tter. PAGES 1 and 2 2.2: Add the following ASTM publications: “B 16 - Rod Bar, and Shapes for Use inScrew Machines Free-Cutting Brass. (DoD adopted) B 36 - Brass Plate, Sheet, Strip, and Rolled Bar. (DoD adopted) B 121 - Leaded Brass Plate, Sheet, Strip, and Rolled Bar. B 135 - Tube Seamless Brass.

9、DoD adopted) B 584 - Casting, Sand, Copper Alloy for General Applications. D 380 - Rubber Hose Methods of Testing. -(DoD adopted) (DoD adopted) (DoD adopted)“ 3.1.2: Delete and substitute: - * “3.1.2 - Couings. - A male coupling shall be attached to one end of the hose and a female swivel coupling

10、to the other end. Coupling shsll be brass and shall be of the reusable compression grip type consisting of a nipple and solid socket sleeve and grip. Threads shaIl conform to FED-STD-H28/10 and shall be as follows: 1-1/2 inch - ii-112 ftii 3/4 inch - -1/2 H . 3.1.2.1 Casting brass. When cast, coupli

11、ng parts shall be made from copper alloy as specified in ASTMB 584, 3i1.2.2 Brass rod and bar. Coupling parts made from bar stock shall con- hrm to cgpper alloy 360 as specified in ACTM B 16. -. 3.1.2.3 - Brass plate sheet, and strie, -Coupling partS.made from sheet stock siia21 conform to copper al

12、loy 260 as specified in ASTM B 36 or copper alfoy 353 as specified in ASTM B 121. 3-1.2.4 I_-_. Brass tubing. .Coupling parts made from tubing shall conform to apper alloy 230 or 269 as specified in ASTM B 135.“ . 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

13、 from IHS-,-,-i Working pressure, minimum NIL-H-24580 (2) i2 7977706 0232734 b MIL-11-24 580 ( SH) AMENDMENT 2 Proof pressure, Burst pressure minimum minimum 3.2, line 2: Delete “two“ and substitute “a minimum OE 2“ and after “braided“ add “or spiraled“. 2 50 3.2.2, line 2: After “50 feet“ add “+ 6

14、inches“ 3.3.1, line 2: After “hardening“, add “in excess of 15 durometer points“. 500 1000 Table I: Delete and substitute: “TABLE I. . .Pressure measur_e_ments. I (Ib/in2, gauge) I (lb/in2, gauge) 1 (lb/in2, gauge) I PAGE 3 3.3.3: Delete and substitute: “3.3.3 Elongation and twist. Elongation and tw

15、ist, when measured at the working pressures shown in tablI, shall be as follows: (a) ElZngation/contraction. - The elongation or contraction of hose shall not exceed plus or minus 6 percent when tested as specifled in 4.5.4. tighten the coupling connection at reel end and in any event shall not exce

16、ed 1/2 degree per foot of hose length.“ (b) - Twist. mist, if any, shall. be in the direction that would Add tt.2 following paragraph: -“3.6 First article. When specified (see 6.2.1), the contractor shall fur- nish sample unit(s) for first article inspection and approval (see 4.2 and 6.3): PAGE 4 4.

17、3.3: Delete and substitute: “4.3.3 Sampling for qualig conformance (group A). Hose sample shall he -._11- selected at random from bulk Lse or coupled hose for the group A tests shown in table III. For the elongation and twist test, the samples shall be selected in accordance with MIL-STD-105 for the

18、 single sampling plan for normal inspection. The general inspection level shall be II with an AQL of 2.5 percent. For the burst test, one +foot section shall be cut from the bulk hose or from one sample coupled hose . “ “4.4.1: Add “If the rejection number exceeds the acceptance number (for the elon

19、gation and twist test) or if the sample 3-foot section fails the burst test, the lot represented by the samples shall be rejected.“ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-24580 (2) 42 = 7997906 0232935 8 = MIL-H-24580(SH) AMENDMENT 2 P

20、AGE 5 NOTE: The margins of this amendment is marked with an asterisk to indicate where a change from the previous amendment was made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in this notation. Bidders and contractors are cautioned to

21、 evaluate the requirements of this document based on the entire content irrespective of the marginal notatlon and relationship to the last previous amendment. 4.5.5: Delete and substitute: “4.5.5 - Burst. The sample 3-foot section of hose selected in accordance with 4.3.3 shall be subjected to the b

22、urst test to determine conformance with table I. The test shall be conducted in accordance with ASTM D 380.“ PAGES 5 and 6 6.2.: Add item (e): “(e) When a first article is required for inspection and approval (see 3.6, 4.2, and 6.3)“. LAST PAGE * DD Form 1426, Standardization Document Improvement Proposal: Delete address and substitute: “COMMANDER NAVAL SEA SYSTEMS COMMAND (SEA 5523) DEPARTMENT OF THE NAVY WASHINGTON, DC 20362-5101“ Preparing activity : Navy - SH (Project 4210-N197) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • EN 1159-2-2003 en Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 2 Determination of thermal diffusivity《高级工业陶瓷 陶瓷复合材料 热机械性能 第2部分 热扩散系数的测定 代替ENV.pdf EN 1159-2-2003 en Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 2 Determination of thermal diffusivity《高级工业陶瓷 陶瓷复合材料 热机械性能 第2部分 热扩散系数的测定 代替ENV.pdf
  • EN 1159-3-2003 en Advanced technical ceramics - Ceramic composites thermophysical properties - Part 3 Determination of specific heat capacity (Incorporating corrigendum April 2008).pdf EN 1159-3-2003 en Advanced technical ceramics - Ceramic composites thermophysical properties - Part 3 Determination of specific heat capacity (Incorporating corrigendum April 2008).pdf
  • EN 1161-1996 en Feather Down - Test Methods - Determination of Moisture Content《羽毛和绒毛的试验方法 湿量测定》.pdf EN 1161-1996 en Feather Down - Test Methods - Determination of Moisture Content《羽毛和绒毛的试验方法 湿量测定》.pdf
  • EN 1162-1996 en Feather and Down - Test Methods - Determination of the Oxygen Index Number《羽毛和绒毛 检验方法 氧指数测定》.pdf EN 1162-1996 en Feather and Down - Test Methods - Determination of the Oxygen Index Number《羽毛和绒毛 检验方法 氧指数测定》.pdf
  • EN 1163-1996 en Feather and Down - Test Methods - Determination of the Oil and Fat Content《羽毛和绒毛 检验方法 油含量和脂含量测定》.pdf EN 1163-1996 en Feather and Down - Test Methods - Determination of the Oil and Fat Content《羽毛和绒毛 检验方法 油含量和脂含量测定》.pdf
  • EN 1164-1998 en Feather and Down - Test Methods - Determination of the Turbidity of an Aqueous Extract《羽毛和绒毛 检验方法 含水萃取物混浊性测定》.pdf EN 1164-1998 en Feather and Down - Test Methods - Determination of the Turbidity of an Aqueous Extract《羽毛和绒毛 检验方法 含水萃取物混浊性测定》.pdf
  • EN 1165-1996 en Feather and Down - Test Methods - Determination of Water-Soluble Chlorides《羽毛和绒毛 检验方法 水溶解氯化物的测定》.pdf EN 1165-1996 en Feather and Down - Test Methods - Determination of Water-Soluble Chlorides《羽毛和绒毛 检验方法 水溶解氯化物的测定》.pdf
  • EN 1167-1996 en Feather and Down - Method of Test for Measuring the Sizes of Quilts Filled with Feather and or Down《羽毛和绒毛 羽毛和绒毛被褥尺寸测量的检验方法》.pdf EN 1167-1996 en Feather and Down - Method of Test for Measuring the Sizes of Quilts Filled with Feather and or Down《羽毛和绒毛 羽毛和绒毛被褥尺寸测量的检验方法》.pdf
  • EN 1168-2005 en Precast concrete products - Hollow core slabs (Incorporates Amendment A3 2011)《预制混凝土产品 空芯板》.pdf EN 1168-2005 en Precast concrete products - Hollow core slabs (Incorporates Amendment A3 2011)《预制混凝土产品 空芯板》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1