NEN-ISO IEC 9318-3-1994 Information technology Intelligent peripheral interface Part 3 Device generic command set for magnetic and optical disk drives (ISO IEC 9318-3 1990)《ISO IEC.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN ISO 12090-2-2016 Rolling bearings - Profiled rail guides for linear motion rolling bearings - Part 2 Boundary dimensions and tolerances for series 4 and 5 (ISO 12090-2 2011)《滚动.pdf

DIN ISO 12123-2011 Optics and photonics - Specification of raw optical glass (ISO 12123 2010)《光学和光子学 未加工的光学玻璃规范(ISO 12123-2010)》.pdf

DIN ISO 12128-1998 Plain bearings - Lubrication holes grooves and pockets - Dimensions types designation and their application to bearing bushes Identical with ISO 12128 1995《滑动轴承 .pdf

DIN ISO 12132-2000 Plain bearings - Quality assurance of thin-walled half-bearings - Design FMEA (ISO 12132 1999)《滑动轴承 薄壁轴瓦的质量保证 设计中的失效形式和影响分析（FMEA）》.pdf

DIN ISO 12151-2-2004 Connections for hydraulic fluid power and general use - Hose fittings - Part 2 Hose fittings with ISO 8434-1 and ISO 8434-4 24 cone connector ends with O-rings.pdf

DIN ISO 12151-3-2012 Connections for hydraulic fluid power and general use - Hose fittings - Part 3 Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends (ISO 12151-3 2010)《液压传动和.pdf

DIN ISO 12164-3-2016 Hollow taper interface with flange contact surface - Part 3 Dimensions of shanks for stationary tools (ISO 12164-3 2014)《带法兰连接表面的中空锥形接口 第3部分 固定式工具柄的尺寸 (ISO 121.pdf

DIN ISO 12164-4-2016 Hollow taper interface with flange contact surface - Part 4 Dimensions of receivers for stationary tools (ISO 12164-4 2014)《带法兰连接表面的中空锥形接口 第4部分 固定式工具承受器的尺寸(ISO.pdf

DIN ISO 12165-2002 Tools for moulding - Components of compression and injection moulds and diecasting dies - Terms and symbols (ISO 12165 2000)《模塑工具 压模和注塑模及压铸模部件 术语和符号 (ISO 12165 2.pdf