SAE AMS 3020A-1997 Oil Reference For L Stock Rubber Testing《L型橡胶轮用参考润滑油试验》.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS3020A AEROSPACE MATERIAL SPECIFICATION AMS3020 REV. A Issued 1978-01 Revised 1

5、997-11 Reaffirmed 2013-09 Superseding AMS3020 (R) Oil, Reference, for “L” Stock Rubber Testing RATIONALE AMS3020A has been reaffirmed to comply with the SAE Five-Year review policy. 1. SCOPE: 1.1 Form: This specification covers a petroleum-base reference oil (See 8.2). 1.2 Application: This fluid ha

6、s been typically used as a reference oil to evaluate the ability of elastomeric compounds to conform to specified requirements after immersion at a specified time and temperature as required by the material. 1.3 Safety - Hazardous Materials: While the materials, methods, applications and processes d

7、escribed or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is the sole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to t

8、ake the necessary precautionary measures to ensure the health and safety of all personnel involved. 2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent supplied herein. The supplier may work to a s

9、ubsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. Copyright SAE International Provided by IHS under license with SAENot

10、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE INTERNATIONAL AMS3020A Page 2 of 5 2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001. AMS 2350 Standards and Test Methods AMS 2825 Material Safety Data Sheets 2.2 ASTM Public

11、ations: Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. ASTM D 92 Flash Point by Cleveland Open Cup ASTM D 445 Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic Viscosity) ASTM D 611 Aniline Point and Mixed Aniline Point of Petroleum

12、Products and Hydrocarbon Solvents ASTM D 4057 Manual Sampling of Petroleum and Petroleum Products 2.3 U.S. Government Publications: Available from DODSSP, Subscription Services Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094. MIL-STD-2073 DoD Material, Procedures for Development a

13、nd Application of Packaging Requirements 3. TECHNICAL REQUIREMENTS: 3.1 Material: Shall consist of a highly refined, hydrotreated, straight-run distillate from crude petroleum containing 0.20% 0.01 of the antioxidant di-t-butyl-p-cresol. 3.2 Properties: The reference base oil shall conform to the re

14、quirements shown in Table 1; tests shall be performed on the oil supplied and in accordance with specified test methods. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE INTERNATIONAL AMS3020A Pag

15、e 3 of 5 TABLE 1 PROPERTIES Property Requirement Test Method 3.2.1 Aniline Point 73 C 1 (163 F 2) ASTM D 611 3.2.2 Viscosity 38 C (163 F) 2.85 - 3.10 mm2/s ASTM D 445 3.3.3 Flash Point (min) 95 C (203 F) ASTM D 92 3.3 Quality: The reference oil as received by purchaser shall be uniform in quality an

16、d condition and free from sediment, suspended matter, and other foreign materials. The odor shall not be nauseating or irritating. 4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The manufacturer of the reference oil shall supply all samples and shall be responsible for all requi

17、red tests. Purchaser reserves the right to sample and to perform such confirmatory testing as deemed necessary to ensure that the reference oil conforms to the requirements of this specification. 4.2 Classification of Tests: All technical requirements are acceptance tests and shall be performed on e

18、ach lot prior to shipment of reference oil by manufacturer. 4.3 Sampling and Testing: Shall be in accordance with ASTM D 4057. Sufficient oil shall be taken at random from each lot to perform all required tests. The number of determinations for each requirement shall be specified in the actual test

19、procedure or, if not specified therein, not less than three. 4.3.1 A lot shall be all oil from one batch presented for manufacturers inspection at one time. 4.4 Approval: 4.4.1 If requested by purchaser sample oil shall be submitted for approval by the purchaser before oil for production use is supp

20、lied, unless such approval be waived. Results of tests on production oil shall be essentially equivalent to those on the approved sample oil. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE INTER

21、NATIONAL AMS3020A Page 4 of 5 4.4.2 Manufacturer shall use ingredients, manufacturing procedures, processes and methods of inspection on production oil which are essentially the same as those used on approved sample. If necessary to make any changes in ingredients or in manufacturing procedures, man

22、ufacturer shall submit for reapproval a statement of the proposed changes in ingredients and processing and, when requested, sample oil. Production oil made by the revised procedure shall not be shipped prior to receipt of reapproval. 4.5 Reports: The supplier of reference oil shall furnish with eac

23、h shipment a report from the manufacturer showing the composition and results of tests to determine conformance to the requirements. This report shall include the purchase order number, lot number, AMS 3020A, manufacturers identification, and quantity. 4.5.1 A material safety data sheet conforming t

24、o AMS 2825, or equivalent, shall be supplied to purchaser prior to, or with the first shipment of the oil. 4.6 Resampling and Retesting: If any sample used in the above tests fails to meet the specified requirements, disposition of the reference oil may be based on the results of testing three addit

25、ional samples for each original nonconforming sample. Failure of any retest sample to meet the specified requirements shall be cause for rejection of the reference oil represented and no additional testing shall be permitted. Results of all tests shall be reported. 5. PREPARATION FOR DELIVERY: 5.1 P

26、ackaging and Identification: 5.1.1 Oil shall be packaged in airtight containers of such size and design as to keep spillage to a minimum. 5.1.2 Each container of reference oil shall be legibly identified with not less than the following information on the attached label, using characters which will

27、not be obliterated by normal handling. OIL, REFERENCE, FOR “L” STOCK RUBBER TESTING AMS 3020A MANUFACTURERS MATERIAL DESIGNATION _ PURCHASE ORDER NUMBER _ LOT (OR BATCH) NUMBER_ QUANTITY _ APPROPRIATE WARNINGS OR PRECAUTIONARY NOTICES _ 5.1.3 Containers of this reference oil shall be prepared for sh

28、ipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of this oil to ensure carrier acceptance and safe delivery. Copyright SAE International Provided by IHS under license with SAENot for Resale

29、No reproduction or networking permitted without license from IHS-,-,-SAE INTERNATIONAL AMS3020A Page 5 of 5 6. ACKNOWLEDGMENT: A supplier shall mention this specification number in all quotations and when acknowledging purchase orders. 7. REJECTIONS: Fluid not conforming to this specification or to

30、modifications authorized by purchaser will be subject to rejection. 8. NOTES: 8.1 The change bar ( l ) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this specification. An (R)

31、symbol to the left of the document title indicates a complete revision of the specification. 8.2 This reference oil is known as ARM 201, the source for procurement of this fluid is SAE Inc., 400 Commonwealth Drive, Warrendale, PA 15096-0001. 8.3 Purchase documents should specify not less than the fo

32、llowing: Title, number, and date of this specification Size of containers desired (See 5.1.1) Quantity of reference oil desired Special packaging, if required. 8.4 Products meeting the requirements of this specification have been classified under Federal Stock Class FSCN 9150. PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “CE” Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-