SAE AMS 4291J-2017 Aluminum Alloy Die Castings 8 5Si - 3 5Cu (A380 0-F) As Cast (UNS A13800).pdf

1、_ 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSX EOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDO and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, LVWKHVROHUHVSR

2、QVLELOLWRIWKHXVHU SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced,

3、 stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-

4、0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS4291J AEROSPACE MATERIAL SPECIFICATION AMS4291 REV. J Issued 1943-10 Revised 2017-01 Superseding AMS4291H Aluminum Alloy,

5、 Die Castings 8.5Si - 3.5Cu (A380.0-F) As Cast (Composition similar to UNS A13800) RATIONALE AMS4291J revises Default Radiographic Acceptance Standards (Table 2), and Method and Frequency of Inspection (3.5.2) and is a Five-Year Review and update of this specification. 1. SCOPE 1.1 Form This specifi

6、cation covers an aluminum alloy in the form of die castings. 1.2 Application These castings have been used typically for components of intricate shape, but not having thin sections, but usage is not limited to such applications. This alloy has good casting characteristics by cold-chamber die casting

7、 and fair resistance to corrosion. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue

8、 is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside US

9、A and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2694 In-Process Welding of Castings AMS2804 Identification Castings ARP1917 Clarification of Terms Used in Aerospace Metals Specifications SAE INTERNATIONAL AMS4291J Page 2 of 6 2.2 ASTM Publications Available from ASTM International, 1

10、00 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM B660 Packaging/Packing of Aluminum and Magnesium Products ASTM E29 Using Significant Digits in Test Data to Determine Conformance with Specifications ASTM E34 Chemical Analysis of Aluminum an

11、d Aluminum-Base Alloys ASTM E505 Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings ASTM E607 Atomic Emission Spectrometric Analysis of Aluminum Alloys by the Point-to-Plane Technique, Nitrogen Atmosphere ASTM E716 Sampling of Aluminum and Aluminum Alloys for Spectrochemical

12、 Analysis ASTM E1251 Analysis of Aluminum and Aluminum Alloys by Atomic Emission Spectrometry ASTM E1417/E1417M Liquid Penetrant Testing ASTM E1742/E1742M Radiographic Examination 2.3 ANSI Accredited Publications Copies of these documents are available online at http:/webstore.ansi.org/. ANSI H35.1/

13、H35.1M Standard Alloy and Temper Designation System For Aluminum 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E34, by spectrochemical methods in accordance with ASTM E607, or ASTM E12

14、51, or by other analytical methods acceptable to purchaser (see 3.4 and 8.2). Table 1 - Composition Element Min Max Silicon Iron Copper Manganese Magnesium Nickel Zinc Tin Other Elements, total Aluminum 7.5 - 3.0 - - - - - - remainder 9.5 1.3 4.0 0.50 0.10 0.50 3.0 0.35 0.50 3.1.1 Test results may b

15、e rounded in accordance with WKHURXQGLQJRIIPHWKRGRI$670( 3.2 Condition As cast (F temper) as defined in ANSI H35.1/H35.1M. SAE INTERNATIONAL AMS4291J Page 3 of 6 3.3 Castings Castings shall be produced from metal conforming to 3.1, determined by analysis of a specimen (3.4) cast after the last melt

16、addition. 3.4 Chemical Analysis Specimen Shall be cast after the last melt addition and shall be tested to qualify the melt lot as in 3.1. Spectrochemical sample shall be prepared in accordance with ASTM E716. 3.5 Quality Castings, as received by purchaser, shall be uniform in quality and condition,

17、 sound, and free from foreign materials and from imperfections detrimental to usage of the castings. 3.5.1 Radiographic, liquid penetrant, and other quality standards shall be as agreed upon by purchaser and producer. When acceptance standards are not specified for radiographic inspection, the requi

18、rements of Table 2 shall apply, utilizing the reference radiographs of ASTM E505. Table 2 - Default radiographic acceptance standards using ASTM E505 Category of Discontinuity Maximum Acceptable Level of Discontinuity 1/8 inch (3.2 mm) Reference Radiograph Maximum Acceptable Level of Discontinuity 5

19、/8 inch (15.9 mm) Reference Radiograph Applicable Casting Section Thickness Up to 3/8 inch (9.5 mm), inclusive Over 3/8 inch (9.5 mm) To 1 inch (25.4 mm), inclusive (1) Category A (Porosity) #2 #2 Category B (Cold Fill) #2 #3 per 1/8 inch (3.2 mm) Reference Radiograph Category C (Shrinkage) N/A #2 C

20、ategory D (Foreign Material) Not greater than reference radiograph Not greater than reference radiograph (1) Standards for thicker casting sections shall be as agreed upon between purchaser and producer. 3.5.2 0HWKRGVRILQVSHFWLRQDQGIUHTXHQFRILQVSHFWLRQVKDOOEHDVDJUHHGXSRQES XUFKDVHUDQGSURGXFHU$ these

21、 shall constitute the approved casting procedure and shall be used for producing production castings. If necessary to make any change in parameters for process control factors, producer shall submit for reapproval, a statement of the proposed change in processing and, when requested, sample casting.

22、 Production castings incorporating the revised operations shall not be shipped prior to receipt of reapproval. SAE INTERNATIONAL AMS4291J Page 5 of 6 4.4.2.1 Control factors for producing castings include, but are not limited to, the following: Type of furnace Furnace atmosphere Alloy additions, flu

23、xing, deoxidation, and gas removal procedures Location and number of gates Location and number of knockout pins Mold temperature and tolerances Injection pressure and tolerances Metal injection temperature; variation of r50 q F (r28 q C) from the established limit is permissible Solidification and c

24、ooling procedures Straightening procedure, when applicable Cleaning operations Methods of inspection Radiographic inspection sampling plan, if used. 4.4.2.1.1 Any of the above process control factors for which parameters are considered proprietary by the producer may be assigned a code designation.

25、Each variation in such parameters shall be assigned a modified code designation. 4.5 Reports The producer of castings shall furnish with each shipment a report showing the results of tests for composition of each melt and stating that the castings conform to the other technical requirements of this

26、specification. This report shall include the purchase order number, melt and lot numbers, AMS4291J, part number, and quantity. 4.6 Resampling and Retesting If any specimen used in the above tests fails to meet the specified requirements, disposition of the castings may be based on the results of tes

27、ting two additional specimens for each original nonconforming specimen. Failure of any retest specimen to meet the specified requirements shall be cause for rejection of the castings represented. Results of all tests shall be reported. 5. PREPARATION FOR DELIVERY 5.1 Identification Shall be in accor

28、dance with AMS2804. 5.1.1 Impregnated castings shall be marked IMP. 5.2 Packaging Castings shall be prepared for shipment in accordance with ASTM B660 and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the castings to ensure carrier a

29、cceptance and safe delivery. 6. ACKNOWLEDGMENT A producer shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Castings not conforming to this specification, or to modifications authorized by purchaser, will be subjec

30、t to rejection. SAE INTERNATIONAL AMS4291J Page 6 of 6 8. NOTES 8.1 Revision Indicator A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symb

31、ol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 The composition shown in 3.1 was previously shown as Composition 2.

32、The former Composition 1 is no longer available. Castings having the composition shown in 3.1 shall be supplied whenever either Composition 1 or Composition 2 is specified on the drawing. 8.3 Terms used in AMS are clarified in ARP1917 and as follows: 8.3.1 Melt A single homogeneous batch of molten m

33、etal to which all melt additions and processing have been completed and from which castings are poured. 8.3.2 Melt Lot Castings poured from a single melt. 8.4 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Cels

34、ius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.5 Purchase documents should specify not less than the following: AMS4291J Part number or die number of castings desired Acceptance standards for non-destructive inspection (see 3.5.1), plus method and frequency of inspection (see 3.5.2) Quantity of castings desired. 8.6 Similar Specifications AMS-QQ-A-591, Alloy 380.0, is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met. PREPARED BY AMS COMM,77(