SAE AS 14184-2000 Nonmetallic Shaft-Coupling Details Engine Driven Accessories《发动机驱动附件的非金属传动联结器细节FSC 6115》.pdf

1、Copyright 2004 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, orotherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT

2、ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.orgSAE Technical Standards Board Rules providethat: “This report is published by SAE to advancethe state oftechnical and engineering sciences.Theuse

3、ofthis reportisentirelyvoluntary, andits applicabilityand suitabilityfor any particularuse,including any patentinfringement arising therefrom,isthe sole responsibility of the user.”SAE reviews each technical reportatleastevery five years atwhich timeitmay bereaffirmed,revised, or cancelled.SAE invit

4、es yourwritten comments and suggestions.SHEET 1 OF 4AS14184THIRD ANGLE PROJECTIONAEROSPACE STANDARDAS14184ISSUED 2000-03 REAFFIRMED 2004-03NONMETALLIC SHAFT-COUPLING DETAILS,ENGINE DRIVEN ACCESSORIESPREPARED BY SAE COMMITTEE AE-1FEDERAL SUPPLY CLASS 6115NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FR

5、OM U.S. MILITARY SPECIFICATION MS14184A(AS), NOTICE 1 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS14184A(AS), NOTICE 1. ANY PART N

6、UMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STA

7、NDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY

8、 QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.NONMETALLIC SHAFT-COUPLING DETAILS,ENGINE DRIVEN ACCESSORIESAERO

9、SPACE STANDARDAS14184SHEET 2 OF 4AS14184NONMETALLIC SHAFT-COUPLING DETAILS,ENGINE DRIVEN ACCESSORIESAEROSPACE STANDARDAS14184SHEET 3 OF 4AS14184NONMETALLIC SHAFT-COUPLING DETAILS,ENGINE DRIVEN ACCESSORIESAEROSPACE STANDARDAS14184SHEET 4 OF 4AS14184REQUIREMENTS:1. SPLINES. MALE SHAFT SPLINES SHALL HA

10、VE A MINIMUM SURFACE HARDNESS OF 34 ROCKWELL C TO A MINIMUMCASE DEPTH OF 0.035 INCHES.2. MATERIAL SELECTION. THE PLASTIC SPLINED BUSHING SHALL BE FABRICATED FROM HIGH STRENGTH, SELF-LUBRICATING POLYMERIC MATERIALS HAVING ULTIMATE COMPRESSIVE STRENGTHS OF A MINIMUM OF28,000 PSI. TYPICAL MATERIALS INC

11、LUDE THE POLYAMIDE, ARAMID AND POLYAMIDE-IMIDE RESINS, BELONGINGTO THE DUPONT VESPEL AND AMOCO TORLON FAMILIES. THE PROCESS OF MATERIAL SELECTION SHOULDCONSIDER STRENGTH, FATIGUE AND AGING PROPERTIES, FLUID COMPATIBILITY, THERMAL EXPOSURE,DIMENSIONAL STABILITY, AND FORMING PROPERTIES.3. SHEAR SECTIO

12、N. THE SHAFT SHALL INCLUDE A SHEAR SECTION ALLOWING THE SHAFT TO SHEAR AT THETORQUE SPECIFIED BY THE SPECIFICATION FOR THE ACCESSORY EQUIPMENT.NOTES:1. DIMENSIONS. ALL LINEAR DIMENSIONS ARE IN INCHES EXCEPT ROUGHNESS WHICH ARE IN MICROINCHES.2. APPLICATION. THE SPECIFIED BUSHINGS MAY BE USED ONLY WI

13、TH INVOLUTE SPLINES HAVING 30 DEGREEPRESSURE ANGLES.3. FINISH. ALL BURRS AND SHARP EDGES SHALL BE REMOVED.4. APPLICATION. THIS COUPLING IS DESIGNED TO BE USED AT THE INTERFACE OF AIRCRAFT ACCESSORIES ANDTHE OUTPUT SHAFT OF THE AIRCRAFT ENGINE DRIVE PAD WITHOUT MODIFICATION OR REPLACEMENT OF THEEXIST

14、ING FEMALE OUTPUT SHAFT. THE FEMALE SHAFT SPLINE SHALL BE THOROUGHLY CLEANED TO REMOVESEDIMENT AND GREASE BEFORE INSTALLATION OF THE BUSHING. THE DESIGN RESULTS IN AN INTERFERENCEFIT OF THE BUSHING INTO THE INVOLUTE SPLINE AND A SLIDING FIT OF THE NEW ACCESSORY SHAFT INTO THEBUSHING.5. INSTALLATION.

15、 THE NONMETALLIC SPLINE ADAPTER IS DESIGNED TO BE INSTALLED IN THE DRIVE SHAFTFEMALE SPLINE PRIOR TO INSTALLING THE DRIVEN ACCESSORY. NONMETALLIC SPLINE ADAPTER ARE INTENDEDTO FIT TIGHTLY IN THE FEMALE SPLINE IN WHICH THEY ARE INSTALLED. TO AVOID DAMAGING THE DRIVE SHAFTOR ACCESSORY SHAFT BEARINGS A

16、ND SEALS, THE SPLINE ADAPTERS SHOULD BE PRESSED INTO THE MATINGSPLINES AND THE PRESSURE SHOULD BE REMOVED AS SOON AS THE SPLINE ADAPTER IS FULLY INSTALLED.6. RETENTION AND PRELOAD. THE NONMETALLIC SPLINE ADAPTERS HAVE BEEN DESIGNED TO FIT TIGHTLY IN NEWFEMALE SPLINES. THE TIGHTNESS OF THE FIT WILL D

17、IMINISH WHEN THE NONMETALLIC ADAPTER IS INSTALLEDIN WORN OR USED FEMALE SPLINES. THE SPLINE ADAPTER HAS BEEN DESIGNED TO FIT TIGHTLY TO ACHIEVE ACOMPRESSIVE PRELOAD WHICH EXTENDS THE OPERATING TORSIONAL RANGE OF THE NONMETALLIC SPLINEADAPTER. THE TIGHT FIT ALSO PROVIDES A RESISTANCE TO AXIAL MOVEMEN

18、T WHICH AFFORDS SOME DEGREEOF RETENTION. HOWEVER, THE APPLICATION GENERALLY SHOULD REQUIRE SOME POSITIVE METHOD OF AXIALRETENTION OF THE PART. POSITIVE RETENTION CAN BE ACHIEVED BY A VARIETY OF METHODS INCLUDINGLENGTHENING THE NONMETALLIC ADAPTER, INCORPORATION OF FLANGES IN THE ADAPTER DESIGN, AND THEUSE OF SNAP OR SPIRAL LOCK RINGS TO LIMIT THE AMOUNT OF AXIAL CLEARANCE.