SAE AS 7001-1990 National Aerospace and Defense Contractors Accreditation Program (NADCAP) Program Description《国家航空航天和国防承包商认证计划(NADCAP)项目描述》.pdf

1、The Engineering Society For Advancing Mobility Land Sea Air and SpaceI N T E R N A T I O N A L400 Commonwealth Drive, Warrendale, PA 15096-0001AEROSPACESTANDARDPrinted in U.S.ASAE Technical Board Rules provide that: “This report is published by SAE to advance the state of technical and engineeringsc

2、iences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patentinfringement arising therefrom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirm

3、ed, revised, or cancelled. SAE invit esyour written comments and suggestions.Submitted for recognition as an American National StandardIssued 1990-07-02Copyright 1990 Society of Automotive Engineers, Inc.All rights reserved.AS7001NATIONAL AEROSPACE AND DEFENSE CONTRACTORSACCREDITATION PROGRAM (NADCA

4、P)1. Scope1.1 This standard describes the National Aerospace and Defense Contractors Accreditation Program (NADCAP) to accredit the capability of suppliers furnishing processes, products, and services for the aerospace and defense industries as provided for in specific programs.2. References2.1 Appl

5、icable Documents2.1.1 SAE PublicationsAvailable from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.AS7002 - National Aerospace and Defense Contractors Accreditation Program (NADCAP) - Rules for ImplementationAS7003 - National Aerospace and Defense Contractors Accreditation Program (NADCAP)

6、- Program Operation2.1.2 ANSI PublicationsAvailable from American National Standards Institute, 1430 Broadway, New York, NY 10018.Z34.1 - Third Party Certification Program2.2 Related Publications2.2.1 Military PublicationsAvailable from Naval Publications and Forms Center, Attn: NPODS, 5801 Tabor Av

7、enue, Philadelphia, PA 19120-5099.PROGRAM DESCRIPTIONCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-SAEAS7001- 2 -2.2.1.1 Federal StandardsFED-STD-368 - Quality Control System Requirements2.2.1.2 Mili

8、tary StandardsMIL-STD-1535 - Supplier Quality Assurance Program Requirements2.2.1.3 Military SpecificationsMIL-Q-9858 - Quality Program RequirementsMIL-l-45208 - Inspection System Requirements2.2.2 ISO PublicationsAvailable from American National Standards Institute, 1430 Broadway, New York, NY 1001

9、8.ISO 9000 - Quality management and quality assurance standards - Guidelines for selection and useISO 9001 - Quality systems - Model for quality assurance in design/development, production, installation and servicingISO 9002 - Quality systems - Model for quality assurance in production and installat

10、ionISO 9003 - Quality systems - Model for quality assurance in final inspection and test3. DESCRIPTION3.1 DesignThe National Aerospace and Defense Contractors Accreditation Program (NADCAP) is designed as a nationally recognized, voluntary, consensus, third-party accreditation program to generate li

11、sts of organizations capable of supplying processes, products, and services for the aerospace industry. Development of this program has been made possible through the active cooperation and continuing support of the aerospace industry, the U.S. Department of Defense (DoD), the Federal Aviation Admin

12、istration (FAA), the General Services Administration (GSA), the National Aeronautical and Space Administration (NASA), the U.S. Armed Services, other federal departments and agencies, and the Society of Automotive Engineers (SAE).NADCAP is designed to simplify and consolidate audits and to assess, w

13、ith appropriate surveillance, the supplier capability to achieve, produce, and maintain NADCAP accreditation requirements.NADCAP provides only accreditation and is not involved with consulting services for suppliers, training of supplier personnel, or formal identification of supplier improvement op

14、portunities for specific processes, products or services.NADCAP is a voluntary program and supplier/contractor/government participation is voluntary.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-SAE

15、AS7001- 3 -3.2 ObjectivesAn objective of NADCAP is to have an easily understood set of requirements enabling suppliers to evaluate their systems and prepare for and maintain NADCAP accreditation. NADCAP requirements have been developed in a structured form to relate to normal supplier organization a

16、nd to permit flexible implementation. The intent is to have a viable requirement standard for use by suppliers with associated audit and inspection criteria for use in accreditation. The requirements are structured to allow tailoring and introduction of new technologies and approaches to organizatio

17、n, management, design, procurement, production, and assurance.A major objective of NADCAP accreditation is to establish and maintain a Qualified Manufacturers List (QML). Maintenance of the QML requires periodic requalification and continuing surveillance for supplier capability and performance in f

18、urnishing identified processes, products, or services.3.3 Audits and SurveillanceAudits are scheduled to interface with supplier activities. Audits and continuing surveillance are expected to be conducted during normal business hours without disruption of normal supplier operations. For continuing s

19、urveillance, suppliers are expected to maintain contact with NADCAP to permit the most opportune scheduling.NADCAP audits and continuing surveillance are performed using published requirements, criteria, and special checklists designed to simplify the auditing process. Checklists for services are co

20、vered in the AS7100 series, while products are covered in the AS7200 series and processes in the AS7300 series. Suppliers should advise NADCAP of any special requirements of their customers so that these may be considered in NADCAP activites.NADCAP auditors and inspectors are selected for their expe

21、rtise in specific areas. NADCAP personnel are selected and operate to avoid conflicts of interest. NADCAP may utilize staff members, committee members, and selected experts as observers or possible participants on audits as part of its continuing program of maintaining the quality of their accredita

22、tion activities.Information from audits and inspections is used to evaluate the capability and performance of supplier processes, products, and services and, ultimately, grant or deny accreditation. The new concept of QMLs is supported by accreditation and updates the former concepts used for Qualif

23、ied Products Lists (QPLs).3.4 Supplier ParticipationIt is important for suppliers to have a thorough understanding of both their responsibilities and necessary actions when working with NADCAP. This includes preliminary stages of applying for accreditation and in working with NADCAP during audits an

24、d continuing surveillance. For the specific requirements of individual programs, refer to the appropriate standard for the process, product, or service involved. By studying NADCAP documents, a supplier will be able to determine the applicability of requirements and criteria to its program and the r

25、equirements of its marketplace.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-SAE AS7001- 4 -3.4 (Continued):NADCAP maintains necessary controls on supplier proprietary information. However, it is int

26、ended that suppliers develop process control systems to demonstrate capability without revealing proprietary information to buyers, third parties, customers, or others with possible conflicting commercial interest.NADCAP will expect suppliers to maintain appropriate interfaces for necessary measurem

27、ent assurance, calibration, personnel, and facility requirements.3.5 AppealsNADCAP has an appeals procedure to provide due process. This procedure is outlined in AS7003, Section 2.6For details on NADCAP and its accreditations, please direct your inquiries to:Operations ManagerNADCAP Technical DivisionPRI402 Commonwealth DriveWarrendale, PA 15086Telephone:(412) 776-4841FAX:(412) 776-0002PREPARED BY THE PRI NADCAP COUNCILCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-