SAE J 2087-2017 Daytime Running Light.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/J2087_201708 SURFACE VEHICLE STANDARD J2087 AUG2017 Issued 1991-08 Revised 2017-08 Superseding

5、J2087 JUN2016 Daytime Running Light RATIONALE 6.9.5 Installation Requirement Reworded to allow multiple lamps per side of vehicle to be activated as a DRL function. TABLE OF CONTENTS 1. SCOPE 3 2. REFERENCES 3 2.1 Applicable Documents 3 2.1.1 SAE Publications . 3 2.2 Related Publications . 3 2.2.1 S

6、AE Publications . 3 2.2.2 CIE Publications 3 2.2.3 UMTRI Publications 3 2.2.4 United Nations UNECE Publications 4 2.2.5 CMVSS Publications . 4 2.2.6 FMVSS Publications . 4 2.2.7 China Publications 4 3. DEFINITIONS . 4 4. LIGHTING IDENTIFICATION CODE, MARKINGS AND NOTICES . 4 5. TESTS . 5 5.1 Photome

7、try 5 5.2 Vibration Test 5 5.3 Warpage Test on Devices with Plastic Components 5 5.4 Color Test 5 5.5 Moisture Test 5 5.6 Dust Test . 5 5.7 Corrosion Test . 5 SAE INTERNATIONAL J2087 AUG2017 Page 2 of 10 6. REQUIREMENTS . 5 6.1 Photometry 5 6.1.1 Dedicated DRL 5 6.1.2 DRLF provided by a Turn Signal

8、or Optically Combined with a Front Position Lamp 5 6.1.3 Headlamp Beam Providing the DRLF . 5 6.1.4 DRL Function Location with Respect to Other Lamps 6 6.2 Vibration 8 6.3 Warpage 8 6.4 Color 8 6.5 Moisture 8 6.6 Dust . 8 6.7 Corrosion . 8 6.8 Materials Requirements 9 6.9 System Requirements . 9 6.9

9、.1 Location on Vehicle Requirement . 9 6.9.2 Area Requirements . 9 6.9.3 Visibility . 9 6.9.4 Light Source Operational Requirements . 9 6.9.5 Installation Requirement . 9 7. GUIDELINES 9 7.1 Telltale . 9 7.2 Operation 10 7.3 Installation . 10 8. NOTES 10 8.1 Revision Indicator 10 Figure 1 Photometri

10、c requirements for dedicated lamp providing drlf with projected luminous lens area of 200 cm2 or less Minimum Luminous Intensity (cd) . 6 Figure 2 Photometric requirements for dedicated lamp providing drlf with projected luminous lens area greater than 200 cm2 Minimum Luminous Intensity (cd). 7 Figu

11、re 3 Photometric requirements for DRLF provided by turn signal lamp or optically combined with front position lamp Minimum Luminous Intensity (cd) 8 SAE INTERNATIONAL J2087 AUG2017 Page 3 of 10 1. SCOPE This SAE Standard provides test procedures, requirements, and guidelines for a daytime running li

12、ght (DRL) function. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall apply. 2.1.1 SAE Publications Available from SAE International, 400 Commonwea

13、lth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. SAE J387 Terminology - Motor Vehicle Lighting SAE J567 Light Source Retention System SAE J575 Test Methods and Equipment for Lighting Devices for Use on Vehicles Less than 2

14、032 mm in Overall Width SAE J576 Plastic Material or Materials for Use in Optical Parts Such as Lenses and Reflex Reflectors of Motor Vehicle Lighting Devices SAE J578 Color Specification SAE J588 Turn Signal Lamps for Use on Motor Vehicles Less than 2032 mm in Overall Width SAE J759 Lighting Identi

15、fication Code SAE J1050 Describing and Measuring the Drivers Field of View SAE J2560 Forward Lighting Halogen Bulb Performance Requirements for Motor Vehicles 2.2 Related Publications The following publications are provided for information purposes only and are not a required part of this SAE Techni

16、cal Report. 2.2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. SAE Lighting Committee DRL Test Reports, 19741989, nine separate reports 2.2.2 CIE Publicat

17、ions Available from CIE Central Bureau, Babenbergerstrasse 9/9A, 1010 Vienna, Austria, Tel: +43 1 714 31 87, www.cie.co.at. CIE TC4.13 Report Automobile Daytime Running Lights (DRL), Third Draft, July 1990 2.2.3 UMTRI Publications Available abstracts, http:/www.umich.edu/industry/complete.html SAE I

18、NTERNATIONAL J2087 AUG2017 Page 4 of 10 2.2.4 United Nations UNECE Publications Available from United Nations Economic Commission for Europe, Palais des Nations, CH-1211, Geneva 10, Switzerland, Tel: +41-0-22-917-12-34, http:/www.unece.org/trans/main/wp29/wp29regs.html. UNECE Regulation No. 48 Unifo

19、rm Provisions Concerning the Approval of Vehicles with Regard to the Installation of Lighting and Light-Signalling Devices UNECE Regulation No. 87 Uniform Provisions Concerning the Approval of Daytime Running Lamps for Power-Driven Vehicles 2.2.5 CMVSS Publications Available from Transport Canada, M

20、otor Vehicle Safety, P.O. Box 8880, Ottawa Post Terminal, Ottawa, Ontario, K1G.3J2 or at www.tc.gc.ca. Canada Motor Vehicle Safety Standard (CMVSS) 108 Lighting Systems and Retro Reflective Devices 2.2.6 FMVSS Publications Available from the Superintendent of Documents, U.S. Government Printing Offi

21、ce, 732 North Capitol Street, NW, Washington, DC 20401 http:/www.gpo.gov/fdsys CFR Title 49 Part 571.108 Lamps, Reflective Devices and Associated Equipment (FMVSS 108) 2.2.7 China Publications GB 23255-2009 Photometric Characteristics of Daytime Running Lamps for Motor Vehicles 3. DEFINITIONS 3.1 DA

22、YTIME RUNNING LAMP (DRL) A lamp providing the daytime running light function. 3.2 DAYTIME RUNNING LIGHT FUNCTION (DRLF) Steady operating light function that is used to improve conspicuity of a vehicle from the front when the regular headlamps are not required for driving. DRL function can be achieve

23、d with low or high beam headlamps, turn signal lamps as well as dedicated lamps. 3.3 DAYTIME RUNNING LIGHT FUNCTION TELLTALE An indicator that provides a visual signal to advise the driver that only the lamps providing DRLF are operating. 4. LIGHTING IDENTIFICATION CODE, MARKINGS AND NOTICES Lamps p

24、roviding DRLF meeting the performance requirements of Section 6 of this document may be identified by the code DRL in accordance with SAE J759. SAE INTERNATIONAL J2087 AUG2017 Page 5 of 10 5. TESTS SAE J575 is a part of this document. The following tests, from that document, are applicable with the

25、modifications as indicated. 5.1 Photometry In addition to the test procedures stated in SAE J575, the following applies: Photometric measurements shall be made with the photometer located at least 3 m from the point where the optical axis intersects the outer surface of the DRL lens. This does not a

26、pply to DRLF provided by headlamps. 5.2 Vibration Test 5.3 Warpage Test on Devices with Plastic Components The light source operation for this test shall be steady burning. 5.4 Color Test 5.5 Moisture Test 5.6 Dust Test 5.7 Corrosion Test 6. REQUIREMENTS Performance Requirements A DRL, when tested i

27、n accordance with the test procedures specified in Section 5, shall meet the following requirements: 6.1 Photometry Shall meet requirements as tested per SAE J575 to the following lamp function types: 6.1.1 Dedicated DRL The device under test shall be designed to conform to the light intensity distr

28、ibution (candela) values shown in Figures 1 or 2, Photometric Requirements for Dedicated Lamp Providing DRLF, when tested in accordance with 5.1. 6.1.2 DRLF provided by a Turn Signal or Optically Combined with a Front Position Lamp The device under test shall be designed to operate at 2.5 times ligh

29、t intensity distribution (candela) values of the base front turn signal, or shall be designed to conform to the light intensity distribution (candela) values as shown in Figure 3 when tested in accordance with 5.1. 6.1.3 Headlamp Beam Providing the DRLF A headlamp providing daytime running light fun

30、ction shall have: a. In the case of low beam headlamps that are designed to conform to SAE J1383, the luminous intensity from the lamp shall be equal to or greater than 40%, but not more than 100% of its designed photometric intensity values when tested at 1.5D-2R in accordance with SAE J575 or b. I

31、n the case of high beam headlamps that are designed to conform to SAE J1383, the luminous intensity shall be greater than 2000 cd, but less than 7000 cd at the H-V test point when tested in accordance with SAE J575. SAE INTERNATIONAL J2087 AUG2017 Page 6 of 10 6.1.4 DRL Function Location with Respec

32、t to Other Lamps If a DRL is located such that its lighted edge is within 100 mm of the optical center of a front turn signal lamp, or within 40mm of a lighted edge of the front turn signal lamp, it must be extinguished or its luminous intensity reduced to a maximum of 250 cd or less at the H-V axis

33、 of the DRL during the turn signal operation. The only exception is when the turn signal is already 2.5 times the required turn signal intensity level. Figure 1 - Photometric requirements for dedicated lamp providing DRLF with projected luminous lens area of 200 cm2 or less Minimum Luminous Intensit

34、y (cd) SAE INTERNATIONAL J2087 AUG2017 Page 7 of 10 Figure 2 - Photometric requirements for dedicated lamp providing DRLF with projected luminous lens area greater than 200 cm2 Minimum Luminous Intensity (cd) SAE INTERNATIONAL J2087 AUG2017 Page 8 of 10 Figure 3 - Photometric requirements for DRLF p

35、rovided by turn signal lamp or optically combined with front position lamp Minimum Luminous Intensity (cd) 6.2 Vibration SAE J575. 6.3 Warpage SAE J575. 6.4 Color SAE J578. The color of the light from a DRL shall be white or yellow as specified in SAE J578. 6.5 Moisture SAE J575. 6.6 Dust SAE J575.

36、6.7 Corrosion SAE J575. SAE INTERNATIONAL J2087 AUG2017 Page 9 of 10 6.8 Materials Requirements Plastic materials used in optical parts shall meet the requirements of SAE J576. 6.9 System Requirements 6.9.1 Location on Vehicle Requirement Lamps providing the DRLF shall be located a. on the front; b.

37、 at the same mounting height, and symmetrically placed laterally relative to the centerline of the vehicle; c. not higher than 864 mm above the road surface, in the case of a high beam headlamp whose reduced luminous intensity is 3000 or more candelas at any location in the beam. 6.9.2 Area Requirem

38、ents The dedicated DRL shall have a minimum unobstructed effective projected luminous lens area of 25 cm2. 6.9.3 Visibility When a DRL is installed on a vehicle, the centroid of the lens area through which the daytime running light function is provided shall be unobstructed and visible from any poin

39、t contained within the solid angle bounded by vertical planes 20 to the left and right of, and horizontal planes 10 above and below, the H-V axis of the lamp. 6.9.4 Light Source Operational Requirements The DRLF, if implemented by use of a filament lamp(s) operated at reduced voltage, shall be certi

40、fied for use by the manufacturer at the intended operating voltage. 6.9.5 Installation Requirement There shall only be one DRLF per vehicle. DRLs shall be mounted symmetrically about the vehicle centerline facing to the front. The cumulative DRLs per side shall comply with the photometric requiremen

41、ts. 7. GUIDELINES 7.1 Telltale 7.1.1 A DRLF telltale shall be located on the instrument panel or in the drivers forward field of view. The telltale shall provide a visual signal only when the DRL system is activated and tail lamps, side marker lamps, license plate lamp and front position lamps are n

42、ot activated. 7.1.2 The telltale shall emit light and have a minimum projected illuminated area of 18 mm2. The minimum required illuminated area of the telltale shall be visible according to the procedures contained in SAE J1050. The steering wheel shall be turned to a straight-ahead position and in

43、 the design location for an adjustable wheel or column. 7.1.3 A DRL telltale needs not be installed on vehicles when: a. DRLF is provided by low beam headlamps operating at full voltage and all exterior marking lamps are activated together with the DRL system or b. There is an automatic photocell sy

44、stem switched from DRLF to night exterior lighting mode. If an automatic photocell system is used to activate the night exterior lighting mode, the light sensor shall activate the lamps when the ambient luminance is less than 1000 lux, on a horizontal surface, indicating dusk, night, or other reduce

45、d light conditions. SAE INTERNATIONAL J2087 AUG2017 Page 10 of 10 7.2 Operation These guidelines apply to how the DRL lamps are used on the vehicle and are not part of the requirements. 7.2.1 The DRLF is to be activated without any switching by the operator (apart from the ignition switch). 7.2.2 No

46、 other lights are required to be illuminated with the DRLF unless full intensity low beam headlamps are used as the DRLF. In this case, those exterior lamps that are required to be illuminated with the low beam headlamps shall be illuminated. 7.2.3 The DRLF is to be deactivated when the low beam hea

47、dlamps and/or fog lamps are switched on. 7.2.4 For vehicles equipped with start-stop engine operation systems; once the Daytime Running Light Function has been turned on, the Daytime Running Light Function shall remain on, during each engine off period of the start-stop engine cycle. 7.3 Installatio

48、n 7.3.1 DRL lamps should be spaced as far apart laterally as practicable and the dedicated DRL lamps should be mounted on the vehicle so the optical centers of the lenses are not less than 250 mm or more than 1500 mm above the road surface. 8. NOTES 8.1 Revision Indicator A change bar (I) located in

49、 the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY T