SAE J 983-1998 Crane and Cable Excavator Basic Operating Control Arrangements《起重机和缆索式挖掘机基本作业操作控制安排》.pdf

1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirelyvoluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefro

2、m, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.QUESTIONS REGARDING THIS DOCUMENT: (724) 772-8512 FAX: (724) 776-0243TO PLACE A DOCUMENT

3、 ORDER; (724) 776-4970 FAX: (724) 776-0790SAE WEB ADDRESS http:/www.sae.orgCopyright 1998 Society of Automotive Engineers, Inc.All rights reserved. Printed in U.S.A.SURFACEVEHICLE400 Commonwealth Drive, Warrendale, PA 15096-0001RECOMMENDEDPRACTICESubmitted for recognition as an American National Sta

4、ndardJ983REAF.OCT1998Issued 1967-04Reaffirmed 1998-10Superseding J983 OCT80Crane and Cable Excavator Basic Operating Control ArrangementsForewordThis reaffirmed document has been changed only to reflect the new SAE Technical Standards Boardformat. References were added to Section 2.1. ScopeThis SAE

5、Recommended Practice applies to mobile, construction type, crane and cable excavatorhand and foot controls. It should not be construed to limit the use of, or to apply to combination controls,automatic controls, or any other special operating control requirements.2. ReferencesThere are no referenced

6、 publications specified herein.3. General NotesThese general notes apply to all six of the control diagrams which cover specific applicationsof crane and cable excavator machines.1. The arrangement of the basic controls should be as shown in the application diagrams (see Figures 1to 6). Controls 1,

7、2, 3, and 4 are levers for hand operation; controls 5 and 6 are pedals for footoperation.2. Controls for other functions, such as auxiliary drums and throttles, may be installed between or besidethe basic controls, but such controls shall be positioned to avoid operator confusion and physicalinterfe

8、rence. Nothing in this document precludes the use of additional controls subject to theforegoing requirements.3. The master clutch control shall be readily operable from the operators seat.4. Controls 2, 3, 5, and 6 should be confined solely to the specified operating functions shown in theapplicati

9、on control diagrams, except for shovel and hoe application. Controls 1 and 4 may betemporarily converted from their specified operating function to operate nonsimultaneous auxiliaryfunctions (that is, travel controlled by swing control) provided that:a. In the specified application, all basic contro

10、ls should operate as specified in the application controldiagram.b. The disconnected function is restrained against unintended movement.Independent controls for any and all basic and auxiliary operating functions are permissible.5. All controls shall return to their released positions automatically

11、upon operator release when notknuckled in.SAE J983 Reaffirmed OCT1998-2-FIGURE 1CRANE CONTROL DIAGRAM(VIEWED FROM OPERATORS SEAT)SAE J983 Reaffirmed OCT1998-3-FIGURE 2HOE CONTROL DIAGRAM(VIEWED FROM OPERATORS SEAT)SAE J983 Reaffirmed OCT1998-4-FIGURE 3SHOVEL CONTROL DIAGRAM(VIEWED FROM OPERATORS SEA

12、T)SAE J983 Reaffirmed OCT1998-5-FIGURE 4DRAGLINE CONTROL DIAGRAM(VIEWED FROM OPERATORS SEAT)SAE J983 Reaffirmed OCT1998-6-FIGURE 5PILE DRIVER CONTROL DIAGRAM(VIEWED FROM OPERATORS SEAT)SAE J983 Reaffirmed OCT1998-7-FIGURE 6CLAMSHELL CONTROL DIAGRAM(VIEWED FROM OPERATORS SEAT)PREPARED BY THE SAE CRAN

13、ES AND LIFTING DEVICES COMMITTEESAE J983 Reaffirmed OCT1998RationaleNot applicable.Relationship of SAE Standard to ISO StandardNot applicable.ApplicationThis SAE Recommended Practice applies to mobile, construction type, crane and cableexcavator hand and foot controls. It should not be construed to limit the use of, or to apply tocombination controls, automatic controls, or any other special operating control requirements.Reference SectionThere are no referenced publications specified herein.Developed by the SAE Cranes and Lifting Devices Committee