SANS 13-2008 Wax polish solvent-based for floors and furniture《地板和家具用基于溶剂的上光蜡》.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 987-0-626-21941-3 SANS 13:2008Edition 2.3SOUTH AFRICAN NATIONAL STANDARD Wax polish, solvent-based, for floors and furniture Published by SABS Stand

4、ards Division 1 Dr Lategan Road Groenkloof Private Bag x191 Pretoria 0001 Tel: +27 12 428 7911 fax: +27 12 344 1568 www.sabs.co.za SABS SANS 13:2008 Edition 2.3 Table of changes Change No. Date Scope Amdt 1 1989 Amended to change the requirement for penetration and to change the footnote that refers

5、 to appendix A. Amdt 2 2004 Amended to change the designation of SABS standards to SANS standards, to change the definition of acceptable, and to convert appendices A and B to form part of the requirements of the specification. Amdt 3 2008 Amended to update the applicable standards and to remove ref

6、erence to national legislation from the text. Foreword This South African standard was approved by National Committee SABS SC 1006A, Detergents, polishes and other chemicals Polishes, in accordance with procedures of SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This

7、document was published in August 2008. This document supersedes SANS 13:2004 (edition 2.2). A vertical line in the margin shows where the text has been technically modified by amendment No.s 1, 2 and 3. In 4.2.1 reference is made to “relevant national regulations and statutory requirements regarding

8、 metrology“. In South Africa it is the Trade Metrology Act, 1973 (Act No. 77 of 1973) as amended from time to time. SANS 13:2008 Edition 2.3 1 Contents Page Foreword 1 Scope . 3 2 Definitions 3 3 Requirements . 3 4 Packing and marking . 5 5 Sampling and compliance with the specification . 6 6 Inspec

9、tion and methods of test 6 6.1 Inspection . 6 6.2 Conditioning of samples 6 6.3 Heat-cool stability 6 6.4 Penetration of paste polishes 7 6.5 Performance . 7 6.6 Non-volatile matter content 7 6.7 Softening point of the non-volatile matter 7 6.8 Ash content of the non-volatile matter . 7 6.9 Flash po

10、int of solvent . 7 6.10 Water content. 7 Appendix A Applicable standards . 8 Appendix B Notes to purchasers . 8 SANS 13:2008 Edition 2.3 2 This page is intentionally left blank SANS 13:2008 Edition 2.3 3 Wax polish, solvent-based, for floors and furniture 1 Scope 1.1 This specification covers two fo

11、rms, i.e. liquid and paste, of solvent-based wax polish suitable for use on furniture and floors, other than those of thermoplastic (asphalt), semi-flexible vinyl (vinyl- asbestos), flexible vinyl, linoleum, and rubber. NOTE a) The titles of standards referred to by number in the specification are g

12、iven in appendix A. b) Requirements that must be specified by the purchaser are listed in appendix B. 2 Definitions 2.1 For the purposes of this specification the following definitions shall apply: acceptable acceptable to the authority administering this standard or to the parties concluding the pu

13、rchase contract, as relvant Amdt 2 batch the material from a single mix defective wax polish or its container or bulk package that fails in one or more respects to comply with the appropriate requirements of the specification lot that quantity of wax polish in containers that bears the same batch id

14、entification, from one manufacturer, submitted at any one time for inspection and testing 3 Requirements 3.1 General The polish shall consist essentially of a wax or a blend of waxes in volatile organic solvents. It shall not be harmful to, or discolour surfaces of the types to which it is intended

15、to be applied. It shall not be irritating to the normal skin and its vapours shall not be toxic to human beings under normal conditions of use. The odour of the polish shall be acceptable. SANS 13:2008 Edition 2.3 4 3.2 Form The wax polish shall be either a liquid or a paste, as specified by the pur

16、chaser, and shall comply with the following requirements: a) Liquid polish. Liquid polish shall be a free-flowing homogeneous liquid between 15 and 30 C and free from lumps or solid particles. b) Paste polish. Paste polish shall be a homogeneous smooth paste free from lumps and granulations. 3.3 Fre

17、edom from grit When approximately 0,1 g of the polish is rubbed between two glass slides, there shall be no evidence of grittiness. 3.4 Heat-cool stability When tested in accordance with 6.3, paste polish shall not show signs of separation, and there shall be not more than 5 mL separation of suspend

18、ed matter from 100 mL of liquid polish. 3.5 Penetration The penetration of paste polish, determined in accordance with 6.4, shall be 50 100 units (tenths of a millimetre) at 20 C and not more than 60 units (tenths of a millimetre) at 25 C. Amdt 1 3.6 Performance When tested in accordance with 6.5, t

19、he polish shall apply easily and shall dry to a thin non-tacky film within 15 min. On rubbing with a soft cloth, the film shall polish smoothly and the gloss of the panel shall not be reduced. 3.7 Non-volatile matter 3.7.1 Content The non-volatile matter content of the polish, determined in accordan

20、ce with 6.6, shall be as follows: a) Liquid polish. Not less than 11,0 % (m/m). b) Paste polish. Not less than 20,0 % (m/m). 3.7.2 Properties The non-volatile matter of the polish shall comply with the requirements given in table 1. SANS 13:2008 Edition 2.3 5 Table 1 Properties of the non-volatile m

21、atter 1 2 3 4 Reguirement Property Liquid Paste Test method Subsection Softening point, C, min. Ash content, % (m/m), max. 75 0,5 75 1,0 6.7 6.8 3.8 Solvent The solvent shall have a flash point, determined in accordance with 6.9, of at least 25 C. 3.9 Water content The water content of the polish, d

22、etermined in accordance with 6.10, shall not exceed 1,0 % (m/m). 3.10 Storage stability When stored at room temperature for 12 months in its original unopened container, the polish shall comply with all the other relevant requirements of the specification. 4 Packing and marking 4.1 Packing Unless co

23、ntainers of a plastics material1)are specified by the purchaser, the polish shall be packed in metal containers. It shall be so packed as to prevent leakage and deterioration of the product, and the containers shall be strong enough to withstand normal handling and transportation. Each container sha

24、ll contain only polish from the same batch. The containers may be packed in bulk packages, but only containers of the same size and bearing the same batch identification shall be packed together in a bulk package. 4.2 Marking 4.2.1 Containers Each container shall bear in prominent, legible, and inde

25、lible marking the information required in terms of the relevant national regulations and statutory requirements regarding metrology (see foreword), and the following additional information: Amdt 3 a) The name or trade name or trade mark of the manufacturer, or a combination of these; b) words to the

26、 effect that the polish is a solvent-based wax polish; c) the net volume of the contents; d) if larger than 1 L, the batch identification. 1) It is not recommended that the container be of polyethylene. SANS 13:2008 Edition 2.3 6 4.2.2 Bulk packages Each bulk package shall bear, in legible and indel

27、ible marking, the following information: a) The information required in terms of 4.2.1(a) and (b); b) the capacity and number of containers; c) the form of the polish; d) the batch identification. 5 Sampling and compliance with the specification NOTE This section applies to the sampling for inspecti

28、on and testing before acceptance or rejection of single lots (consignments) in cases where no information about the implementation of quality control or testing during manufacture is available to help in assessing the quality of the lot. It is also used as the procedure for adjudicating in cases of

29、dispute. 5.1 Sampling The following sampling procedure shall be applied in determining whether a lot complies with the appropriate requirements of the specification. The sample so drawn shall be deemed to represent the lot. After inspecting the lot for compliance with the appropriate requirements of

30、 section 4, take from it at random at least six containers and mark each container with the date of sampling and, when relevant, the batch number. 5.2 Compliance with the specification The lot shall be deemed to comply with the requirements of the specification if, after inspection of the lot and in

31、spection and testing of the sample taken in accordance with 5.1, no defective is found. 6 Inspection and methods of test 6.1 Inspection Inspect the containers in the sample taken in accordance with 5.1 for compliance with the appropriate requirements of section 4, and after conditioning (see 6.2), c

32、heck their contents for compliance with those requirements of the specification with which compliance is not assessed by the tests given in 6.3 6.10 (inclusive). 6.2 Conditioning of samples Condition all samples at room temperature for at least 7 d before testing. 6.3 Heat-cool stability Use SANS 59

33、76. SANS 13:2008 Edition 2.3 7 6.4 Penetration of paste polishes Use SANS 5977 but modified as follows: a) Condition one of the two test samples at 20,0 0,5 C for 24 h and the other sample at 25,0 0,5 C for 24 h. b) Determine the penetration of the polish conditioned at 20,0 0,5 C, using the 60/90 c

34、one, and the penetration of the sample conditioned at 25,0 0,5 C, using the 90 cone. c) Report the penetration of the polish at 20 C and at 25 C. Amdt 1 6.5 Performance Use SANS 5978. 6.6 Non-volatile matter content Use SANS 5981. Amdt 3 6.7 Softening point of the non-volatile matter Use SANS 5980.

35、6.8 Ash content of the non-volatile matter Use SANS 5981. 6.9 Flash point of solvent Use ASTM D93. 6.10 Water content Use SANS 5982. SANS 13:2008 Edition 2.3 8 Appendix2)A Amdt 1 Applicable standards (This appendix does not form part of the requirements of the specification) Amdt 1; amdt 2 Reference

36、 is made to the latest issues of the following standards: ASTM D93, Standard test methods for flash point by Pensky-Martens closed cup tester. SANS 5976, Heat-cool stability of wax polishes. SANS 5977, Penetration of wax (paste) polishes. SANS 5978, Performance of wax polishes. SANS 5979, Non-volati

37、le matter content of wax polishes. Amdt 3 SANS 5980, Softening point of the non-volatile matter of wax polishes. SANS 5981, Wax polishes Non-volatile matter content and the ash content of non-volatile matter. Amdt 3 SANS 5982, Water content of solvent-based wax polishes. Appendix B Notes to purchase

38、rs (This appendix does not form part of the requirements of the specification) Amdt 1; amdt 2 The following requirements must be specified in tender invitations and in each order or contract: a) The form of polish (see 3.2) b) When relevant, that the container in which the polish is packed be of a plastics material (see 4.1) SABS 2) The information in the appendices is additional to that in the specification and has been included purely for information and guidance. Amdt 1