SANS 1360-3-2008 Size designation of clothes Part 3 Infants- garments《服装的尺码标示 第3部分 婴儿衣服》.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21169-1 SANS 1360-3:2008Edition 1.2Any reference to SABS 1360-3 is deemedto be a reference to this standard(Government Notice No. 1373 of

4、8 November 2002)SOUTH AFRICAN NATIONAL STANDARD Size designation of clothes Part 3: Infants garments Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa

5、SANS 1360-3:2008 Edition 1.2 Table of changes Change No. Date Scope Amdt 1 1984 Amended to change its category from a SABS standard specification to a SABS specification. Amdt 2 2008 Amended to change the designation of SABS standards to SANS standards, with no technical changes. Foreword This South

6、 African standard was approved by National Committee StanSA SC 5110.05A, Clothing and made-up articles Clothing, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This document was published in March 2008. This document supersedes SABS 1360

7、-3:1982 (edition 1). Preface This part of the specification has been prepared under the direction of the SABS Clothing Committee. It is, in technical content, identical to ISO 3638. The specification is one of a series which deals essentially with the size designation of clothes, and is not directly

8、 concerned with sizing systems as such. The primary aim of this specification is, as in the other specifications in the series, to establish a size designation system that is based on body measurements, and that indicates (in a simple, direct, and meaningful manner) the body size of the infant that

9、a garment is intended to fit. Provided that the infants height has been accurately determined, this system will facilitate the choice of garments that fit. Choice of garment measurements is normally left to the designer and the manufacturers, who are concerned with the style, cut, and other fashion

10、elements, and who must make due allowance for garments normally worn beneath a specific outer garment or accessory. SANS 1360-3:2008 Edition 1.2 1 Contents Page Foreword Preface 1 Scope . 3 2 Definitions 3 3 Control dimension 3 4 Size designation . 3 5 Labelling . 4 Appendix A Applicable standards 7

11、 Appendix B Examples of infants garments . 7 SANS 1360-3:2008 Edition 1.2 2 This page is intentionally left blank SANS 1360-3:2008 Edition 1.2 3 Size designation of clothes Part 3: Infants garments 1 Scope 1.1 This part of the specification establishes a system of designating the sizes of infants ga

12、rments. Both the control dimension on which the size designation system is based, and the method of indicating the size designation on a garment label, are specified. NOTE a) The standards referred to in this part of the specification are listed in appendix A. b) Examples of garments covered by this

13、 part of the specification are given in appendix B. 2 Definitions 2.1 For the purposes of this part of the specification the definitions given in SANS 10184 and the following definitions shall apply: infant a male or female person of height 104 cm or less standard pictogram a pictogram symbol used t

14、o indicate the position on the body of the relevant control dimensions (see figure 1) 3 Control dimension 3.1 The control dimensions for infants garments shall be height. 4 Size designation 4.1 General The size designation of each garment shall comprise the control dimension (see 3.1), in centimetre

15、s, of the intended wearer of that garment. Where practicable, the standard pictogram shall be used as a means of indicating the size designation. Where it is not practicable to use the standard pictogram, the SANS 1360-3:2008 Edition 1.2 4 numerical value of the control dimension shall be given toge

16、ther with the description of that dimension. NOTE The above requirements shall not preclude the use of size designations shown as a range by stating the minimum and maximum control dimensions separated by an oblique stroke or a hyphen. 4.2 Use of the standard pictogram 4.2.1 The minimum size of the

17、pictogram is not specified but it shall be large enough to convey immediate understanding and to allow the use of readily legible numerals. NOTE The recommended type for use on pictograms is UNIVERS No. U-59. 4.2.2 The height measurement shall be shown on the right-hand side of the pictogram. 4.3 Ga

18、rment measurements Garment measurements shall not be incorporated in the size designation but, where considered of value, they may be indicated separately (see 5.3). 5 Labelling 5.1 Method The size designation of each garment shall be indicated clearly, conspicuously, and in plainly legible form on

19、a label, or on a swing ticket, or on both, Numerals shall, in all cases, be readily discernible. 5.2 Attachment The label or swing ticket shall be securely attached to the garment in a position where it is easily readable. 5.3 Additional information Information additional to the size designation may

20、 be separately indicated on the label, or on the swing ticket, or on both, provided that it does not in any way reduce the prominence and conspicuousness of the size designation. Such additional information may include a size code number, body measurement(s), or garment measurement(s) considered to

21、constitute useful information. 5.4 Examples of labels The examples of labels given in figure 2 illustrate methods of labelling that range from the simple indication on the standard pictogram of the control dimension to more elaborate forms that provide additional information such as a garment measur

22、ement or a size code number. Where the size designation is supplemented by a size code number, separation of the two, as illustrated, renders the size code number readily recognizable as being part of a system of a size designation adopted for a limited population group only. SANS 1360-3:2008 Editio

23、n 1.2 5 Figure 1 Standard pictogram SANS 1360-3:2008 Edition 1.2 6 a) Infants dress or Height 68 b) Infants matinee jacket Height 60 or Garment length 351)Size code 2 c) Infants buster suit Height 86 or To fit:1) chest girth 52-56 Figure 2 Examples of labels for infants garments 1) Examples of addit

24、ional information included in accordance with 5.3. SANS 1360-3:2008 Edition 1.2 7 Appendix A2)Applicable standards Reference is made to the latest issues of the following standards: ISO 3638, Size designation of clothes Infants garments. SANS 10184 (SABS 0184), Definitions for and measurement of bod

25、y dimensions. Appendix B Examples of infants garments a) Coats. b) Jackets, anoraks, tunic tops. c) Dresses. d) Skirts. e) Trousers, shorts, pants. f) Knitted garments such as jumpers, matinee jackets. g) Buster suits, rompers. Standards South Africa 2) The information in the appendices is additional to that in this part of the specification and has been included purely for amplification and guidance.