SANS 1360-5-2008 Size designation of clothes Part 5 Headwear《服装的尺码标示 第5部分 头饰》.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21171-4 SANS 1360-5:2008Edition 1.2Any reference to SABS 1360-5 is deemedto be a reference to this standard(Government Notice No. 1373 of

4、8 November 2002)SOUTH AFRICAN NATIONAL STANDARD Size designation of clothes Part 5: Headwear Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 136

5、0-5:2008 Edition 1.2 Table of changes Change No. Date Scope Amdt 1 1984 Amended to change its category from a SABS standard specification to a SABS specification. Amdt 2 2008 Amended to change the designation of SABS standards to SANS standards, with no technical changes. Foreword This South African

6、 standard was approved by National Committee StanSA SC 5110.05A, Clothing and made-up articles Clothing, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This document was published in March 2008. This document supersedes SABS 1360-5:1982

7、(edition 1). Preface This part of the specification has been prepared under the direction of the SABS Clothing Committee. It is, in technical content, identical to ISO 4417. The specification is one of a series which deals essentially with the size designation of clothes, and is not directly concern

8、ed with sizing systems as such. The primary aim of this specification is, as in the other specifications in the series, to establish a size designation system that is based on body measurements, and that in this case indicates (in a simple, direct, and meaningful manner) the size of the head of the

9、person that an item of headwear is intended to fit. Provided that the size of the persons head (as indicated by the appropriate dimensions) has been accurately determined, this system will facilitate the choice of headwear that fits. Choice of headwear measurements is normally left to the designer a

10、nd the manufacturers, who are concerned with the style, cut, and other fashion elements. SANS 1360-5:2008 Edition 1.2 1 Contents Page Foreword Preface 1 Scope . 3 2 Definitions 3 3 Control dimension . 3 4 Size designation 3 5 Labelling 4 Appendix A Applicable standards 6 SANS 1360-5:2008 Edition 1.2

11、 2 This page is intentionally left blank SANS 1360-5:2008 Edition 1.2 3 Size designation of clothes Part 5: Headwear 1 Scope 1.1 This part of the specification establishes a system of designating the sizes of headwear. Both the control dimension on which the size designation system is based, and the

12、 method of indicating the size designation on headwear item labels, are specified. NOTE The standards referred to in this part of the specification are listed in appendix A. 2 Definitions 2.1 For the purposes of this part of the specification the relevant definitions given in SANS 10184 and the foll

13、owing definition shall apply: standard pictogram a pictogram symbol used to indicate the position on the body of the relevant control dimensions (see figure 1) 3 Control dimension 3.1 The control dimensions for headwear shall be head girth. 4 Size designation 4.1 General The size designation shall c

14、omprise the control dimension (i.e. head girth), in centimetres, of the intended wearer. Where practicable, the standard pictogram shall be used as a means of indicating the size designation. Where it is not practicable to use the standard pictogram, the numerical value of the control dimension shal

15、l be given together with the descriptive words “head girth“. NOTE The above requirements shall not preclude the use of a size designation shown as a range by stating the minimum and maximum control dimensions separated by an oblique stroke or hyphen. SANS 1360-5:2008 Edition 1.2 4 4.2 Use of standar

16、d pictogram 4.2.1 The minimum size of the pictogram is not specified but it shall be large enough to convey immediate understanding, and to allow the use of readily legible numerals. NOTE The recommended type for use on pictograms is UNIVERS No. U-59. 4.2.2 The girth measurement(s) shall be shown on

17、 the left-hand side of the pictogram. 4.3 Headwear measurements Headwear measurements shall not be incorporated in the size designation but, where considered of value, they may be indicated separately (see 5.3). 5 Labelling 5.1 Method The size designation of each item of headwear shall be indicated

18、clearly, conspicuously, and in plainly legible form on a label, or on a swing ticket, or on both. Numerals shall, in all cases, be readily discernible. 5.2 Attachment The label or swing ticket shall be securely attached to the headwear in a position where it is easily readable. 5.3 Additional inform

19、ation Information additional to the size designation may be separately indicated on the label, or on the swing ticket, or on both, provided that it does not in any way reduce the prominence and conspicuousness of the size designation. Such additional information may include a size code number or hea

20、dwear measurement considered to constitute useful information. 5.4 Examples of labels The examples of labels given in figure 2 illustrate methods of labelling that range from the simple indication on the standard pictogram to more elaborate forms that provide additional information, such as a size c

21、ode number. Where the size designation is supplemented by a size code number, separation of the two, as illustrated, renders the size code number readily recognizable as being part of a system of a size designation adopted for a limited population group only. SANS 1360-5:2008 Edition 1.2 5 Figure 1

22、Standard pictogram a) Girls school hat Head girth 531)or Size code 6 b) Infants knitted cap or Head girth 42-45 Figure 2 Examples of labels for headwear 1) Examples of additional information included in accordance with 5.3. SANS 1360-5:2008 Edition 1.2 6 Appendix A2)Applicable standards Reference is

23、 made to the latest issues of the following standards: ISO 4417, Size designation of clothes Headwear. SANS 10184 (SABS 0184), Definitions for and measurement of body dimensions. Standards South Africa 2) The information in the appendix is additional to that in this part of the specification and has been included purely for amplification and guidance.