1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-23639-7 SANS 500:2009Edition 1SOUTH AFRICAN NATIONAL STANDARD Inspection, examination and testing of manually operated chain blocks and ch
4、ain lever hoists in use Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 500:2009 Edition 1 Table of changes Change No. Date Scope Foreword This South African standard was approved by Na
5、tional Committee SABS TC 1020, Lifting equipment, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This document was published in December 2009. Reference is made in 2.1 to the “relevant national legislation“. In South Africa this mea
6、ns the Engineering Profession Act, 2000 (Act No. 46 of 2000). Reference is made in 5.5 to the “relevant national legislation“. In South Africa this means the Occupational Health and Safety Act, 1993 (Act No. 85 of 1993) (as amended). SANS 500:2009 Edition 1 1 Contents Page Foreword 1 Scope . 3 2 Def
7、initions 3 3 Facilities and equipment 4 4 Safety assessment. 4 5 Inspection and examination . 4 6 Overload protection device 5 7 Proof load and brake test. 5 8 Documentation. 6 Bibliography. 7 SANS 500:2009 Edition 1 2 This page is intentionally left blank SANS 500:2009 Edition 1 3 Inspection, exami
8、nation and testing of manually operated chain blocks and chain lever hoists in use 1 Scope This standard specifies the requirements for the inspection, examination and testing of manually operated chain blocks and chain lever hoists in use. This standard does not cover pneumatic and power driven cha
9、in blocks. 2 Definitions For the purposes of this document, the following definitions apply. 2.1 competent person person having the knowledge, training, experience and qualifications specific to the work or task being performed as specified in the relevant national legislation (see foreword) 2.2 exa
10、mination detailed study by a competent person in such depth and detail as the competent person considers necessary to enable him/her to determine whether the equipment being examined is safe to remain in use 2.3 hoist manually operated chain block and chain lever hoist 2.4 inspection visual checking
11、 of all visible components 2.5 proof load test test during which the chain block or chain lever hoist is operated with an applied load NOTE See 6.1.3. 2.6 register document that is used to record all particulars of incidents, modifications, repairs, inspections, examination and testing of the chain
12、block or chain lever hoist SANS 500:2009 Edition 1 4 2.7 safe working load SWL maximum mass that the hoist can safely raise, lower or suspend under specific service conditions NOTE The SWL is normally the same as the WLL and it may be less, but never more. 2.8 technical data documentation containing
13、 manufacturers standards, operating and maintenance procedures, safety critical component data, spare part lists and exploded view diagrams 2.9 user person or organization that has control of the hoist, the lifting operation and the operator 2.10 working load limit WLL maximum mass that a chain bloc
14、k is designed to raise, lower or suspend NOTE The WLL is equal to or greater than the SWL. 3 Facilities and equipment 3.1 The competent person shall have access to suitable and adequate facilities and equipment to permit all activities associated with the inspection, examination and testing to be ca
15、rried out. Examples of such facilities and equipment are as follows: a) test and measuring equipment; b) cleaning facilities; and c) a well-lit area. 3.2 Testing and measuring equipment shall be maintained and fit for purpose. 3.3 Testing and measuring equipment shall be calibrated and certified at
16、least every 12 months or as recommended by the equipment manufacturer. 4 Safety assessment Before the inspection, examination and testing of manually operated chain blocks and chain lever hoists, hazards pertaining to the equipment, environment and working area shall be identified by the competent p
17、erson. Where necessary, corrective action shall be taken. 5 Inspection and examination 5.1 The inspection and examination shall be performed by a competent person in accordance with the hoist manufacturers standards and recommendations on inspection and examination. 5.2 Hoists that do not comply wit
18、h the manufacturers standards shall be promptly identified as non-compliant. SANS 500:2009 Edition 1 5 5.3 In the absence of the manufacturers recommendations and also technical data, the hoist shall be identified as non-compliant. 5.4 Examination and testing shall not be carried out if the hoist wa
19、s found to be non-compliant. 5.5 The frequency of inspection and examination shall not exceed the requirements specified in the relevant national legislation (see foreword). 5.6 The hoist shall be subjected to a proof load and brake test (see clause 7) after every examination. 6 Overload protection
20、device 6.1 If the hoist is fitted with an overload protection device, the device shall not be removed before the proof load test and brake test. 6.2 The hoist shall be subjected to a proof load and brake test and the test load in 7.3 to ensure that the overload protection device functions in accorda
21、nce with the manufacturers standards. 7 Proof load and brake test 7.1 The proof load and brake test shall be carried out by a competent person at intervals not exceeding 12 months. NOTE More frequent inspection and testing should be considered based on the frequency of use and utilization of the mec
22、hanism. 7.2 An examination (see clause 5) shall be conducted before testing. 7.3 All hoists shall be subjected to a test load that is not less than 1,25 WLL and that does not exceed 1,5 WLL in such a way that every part of the hoist is stressed accordingly, i.e. every component shall be subjected to
23、 one full cycle. 7.4 The brake shall engage immediately when lifting or lowering under load is interrupted. 7.5 A hoist shall be considered fit for use provided that it lifts, lowers and sustains the test load in any working position as designed for. 7.6 If a lever hoist is fitted with a free chaini
24、ng device, the brake operation when such device is activated shall only be possible under a load of less than 30 kg or 3% of the WLL, whichever is the greater. 7.7 After the test, the visible components of the hoist shall be inspected and shall be free from any deformation and defects. 7.8 If a hois
25、t is fitted to a structure (for example an overhead beam), all the components shall be subjected to the requirements of 7.3. SANS 500:2009 Edition 1 6 8 Documentation 8.1 General 8.1.1 After every inspection, examination and test, a report shall be compiled. The report shall contain at least the inf
26、ormation given in 8.2. 8.1.2 All certificates of test shall be endorsed with the identity information necessary to ensure that there is no ambiguity as to the type of hoist at the time of test. 8.1.3 The original copy of the report should be given to the user. 8.1.4 The user shall keep on his/her pr
27、emises a register with full particulars of any examination or test (or both) prescribed by this standard. 8.2 Information to be contained in a report The examination report or test certificate (or both) shall contain at least the following information: a) the name and address of the user for whom th
28、e examination or test (or both) was conducted; b) sufficient particulars (for example the brand, serial number and chain batch number) to identify the hoist; c) the date of the examination or test (or both); d) the WLL of the hoist; e) the test load that was applied; f) a statement to the effect tha
29、t the lifting equipment is safe to operate/fit for use; g) identification of any part found to have a defect, which is, or could become, a danger to persons, and a description of the defect; h) the name, address and qualifications of the competent person conducting either the inspection, examination
30、 or test; and i) the date of the report and the signature of the competent person conducting the inspection, examination and test. SANS 500:2009 Edition 1 7 Bibliography ANSI/ASME B 30.21, Manually lever operated hoists. JIS B 8819, Manually operated chain lever hoists. SANS 1594, Manually operated
31、chain blocks. SANS 1636, Manually operated chain lever hoists. SANS 1637, Reconditioned manually operated chain lever hoists. SANS 1640, Reconditioned manually operated chain hoists. SABS This page has been left blank intentionally SABS Standards Division The objective of the SABS Standards Division
32、 is to develop, promote and maintain South African National Standards. This objective is incorporated in the Standards Act, 2008 (Act No. 8 of 2008). Amendments and Revisions South African National Standards are updated by amendment or revision. Users of South African National Standards should ensur
33、e that they possess the latest amendments or editions. The SABS continuously strives to improve the quality of its products and services and would therefore be grateful if anyone finding an inaccuracy or ambiguity while using this standard would inform the secretary of the technical committee respon
34、sible, the identity of which can be found in the foreword. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 The SABS offers an individual notification service, which ensures that subscribers automatically receive notification regarding amendments and revisions to South African National Standards. T
35、el: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za Buying Standards Contact the Sales Office for South African and international standards, which are available in both electronic and hardcopy format. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za Sout
36、h African National Standards are also available online from the SABS website http:/www.sabs.co.za Information on Standards The Standards Information Centre provides a wide range of standards-related information on both national and international standards, and is the official WTO/TBT enquiry point f
37、or South Africa. The Centre also offers an individual updating service called INFOPLUS, which ensures that subscribers automatically receive notification regarding amendments to, and revisions of, international standards. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za Copyr
38、ight The copyright in a South African National Standard or any other publication published by the SABS Standards Division vests in the SABS. Unless exemption has been granted, no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means without prior written
39、permission from the SABS Standards Division. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any purpose other than implementation, prior written permission must be obtained. Details and advice can be obtained from the Senior Manager. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1