UL 1017 CRD-2013 UL Standard for Safety Vacuum Cleaners Blower Cleaners and Household Floor Finishing Machines - Section Paragraph Reference 4 8 1 1 4 8A 5 29 Subject Motor Requir.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUNDERWRITERS LABORATORIES INC. CERTIFICATION REQUIREMENT DECISIONThis Certification Requirement Decision is prepared and published by Underwriters Laboratories Inc.(UL). It is normative for the a

2、pplicable UL Product Certification Program(s); however, it is currently notpart of the UL Standard(s) referenced below.Product Category (CCN): DMLWStandard Number: UL 1017Standard Title: Standard for Vacuum Cleaners, Blower Cleaners, and HouseholdFloor Finishing MachinesEdition Date: September 10, 2

3、010Edition Number: 8Section / Paragraph Reference: 4.8.1.1, 4.8A, 5.29Subject: Motor RequirementsDECISION:4.8 Motors4.8.1 General4.8.1.1 Motors shall comply with the Standard for Rotating Electrical Machines - General Requirements,UL 1004-1, or be evaluated in the end-use by the applicable requireme

4、nts of this end-product standard,and shall be of a type suitable for the particular application; see Clause 4.8A. They shall be capable ofcarrying the normal load (see Clause 5.2) without exceeding the permissible temperatures when theappliance is tested in accordance with the temperature test, Clau

5、se 5.8.Exception: A motor provided with integral insulation (e.g. epoxy coating) in lieu of slot liners shall alsocomply with the Standard for Systems of Insulating Materials - General, UL 1446, and the integralinsulation requirements specified in Clause 5.29.4.8A Motors4.8A.1 Motors having a NEMA f

6、rame size shall comply with the Standard for Motors and Generators,C22.2 No. 100 and the Standard for Rotating Electrical Machines - General Requirements, UL 1004-1.This includes fractional HP motors rated up to 1 HP (typically NEMA frame sizes 42, 48, or 56), andintegral HP motors rated 1 HP and gr

7、eater (typically NEMA frame sizes 140 - 449T).4.8A.2 Motors not enclosed, or partially enclosed, by the end product enclosure shall comply with theStandard for Motors and Generators, C22.2 No. 100 and the Standard for Rotating Electrical Machines -General Requirements, UL 1004-1.4.8A.3 Motors comple

8、tely enclosed within the end product enclosure shall comply with one of thefollowing:a) The Standard for Motors and Generators, C22.2 No. 100 and the Standard for RotatingElectrical Machines - General Requirements, UL 1004-1; orb) The Standard for Rotating Electrical Machines - General Requirements,

9、 UL 1004-1 exceptas noted in Table 26; orUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULc) The motor shall comply with the following construction requirements and the applicableperformance requirements (when tested in conjunction with the end

10、 product), of this endproduct standard:1) Protection against corrosion, Clause 4.3.2) Terminal compartment, Clause 4.4.5.3) Internal wiring, Clause 4.6.4) Electrical Insulation, Clause 4.7.5) Motors, Clause 4.8.6) Capacitors, Clause 4.10.7) Spacings, Clause 4.13.8) Grounding, Clause 4.14.4.8A.4 A mo

11、tor located in an extra-low voltage circuit is evaluated for the risk of fire and personal injuryin accordance with the applicable requirements of this end product standard.Table 26 - Superseded requirements(See Clause 4.8A.3b)UL 1004-1 exempted requirement Superseded by the requirements in this end

12、-productstandardCurrent and Horsepower Relation Clause 4.13.1.10Cord-Connected Motors Clause 4.4.1Factory Wiring Terminals and Leads Clause 4.6Electrical Insulation Clause 4.7Non-Metallic Functional Parts Clauses 4.1, 4.7, and 4.8Solid-State Controls, 7.2 Clause 4.9Non-metallic enclosure thermal agi

13、ng, 9.1.4 Clauses 4.1 and 4.7Motor enclosure - Cast Metal Enclosures, Sheet MetalEnclosures, and Polymeric EnclosuresClause 4.1Grounding, and Grounding Identification Clause 4.14Ventilation Openings: only applicable where the openings areon surfaces considered to be the appliance enclosure.Clause 4.

14、1.3Accessibility of Uninsulated Live Parts, Film-Coated Wire, andMoving PartsClause 4.1.5Protection Against Corrosion Clause 4.3Available fault current ratings for motor start and runningcapacitors, Clause 26.6: not applicable for cord and plugconnected appliances.Clause 4.10Switches is not applicab

15、le to centrifugal starting switches Clause 4.19With the exception Resilient Elastomer Mounting Tests andElectrolytic Capacitor Overvoltage Tests, respectively, theperformance tests are not applicableAll applicable performance tests.STANDARD NUMBER: UL 1017 -2-UL COPYRIGHTED MATERIAL NOT AUTHORIZED F

16、OR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULTable 26 - Superseded requirements ContinuedUL 1004-1 exempted requirement Superseded by the requirements in this end-productstandardOnly the following marking requirements specified in 43.1 areapplicable: manufacturers name or identif

17、ication; ratedvoltage; rated frequency; number of phases if greater than 1;and multi-speed motors, other than a shaded-pole or apermanent-split-capacitor motor, shall be marked with theamperes and horsepower at each speedClause 10.1.15.29 Integral insulation5.29.1 Samples of a wound component, stato

18、r, or rotor having integral insulation (e.g., epoxy coating) inlieu of slot liners, for use in machines rated 250 V and less, shall be subjected to the tests described inClauses 5.29.2 through 5.29.7.5.29.2 The components shall be subjected to a dielectric strength test of 1000 V for 1 min withoutbr

19、eakdown, except that where the wound component is for use in machines rated above 250 V, thecomponents shall be subjected to a dielectric strength test of 1000 V plus twice the rated voltage for 1min without breakdown.5.29.3 The samples shall be subjected to one of the following conditioning cycles,

20、 and then followed bya conditioning of 24 h at 30C (86F) at a relative humidity shall be 80 to 90%. A temperature toleranceof 2C (3F) shall be permitted.a) 24 h at 175C (347F) for Class A;b) 24 h at 200C (392F) for Class B; orc) 24 h at 220C (428F) for Class F insulation.5.29.4 The conditioning cycl

21、e described in Clause 5.29.3 shall be repeated once, and then the samplesshall be immersed in a hard water solution of 0.5 g of calcium sulphate (CaSO4) per liter of distilled waterfor 24 h at a temperature of 25 2C (77 3F).5.29.5 The samples shall be air dried in an essentially draft-free area for

22、not less than7hat205C witha max RH of 50%.5.29.6 The insulation resistance of the samples shall be measured using 500 Vdc at room temperature.The insulation resistance shall be not less than 500 k.5.29.7 The dielectric strength test described in Clause 5.29.2 shall be repeated, and all samples shall

23、pass without breakdown.RATIONALE FOR DECISION:This Certification Requirement Decision documents the requirements for motors used in UL 1017appliances. In the past, motors have either complied with the motor standard UL 1004-1 or complied withthe applicable requirements in UL 1017. The Integral Insul

24、ation requirements are derived from C22.2 No.100-04 (R2009). This reflects present practice regarding the application of these requirements.Copyright 2013 Underwriters Laboratories Inc.STANDARD NUMBER: UL 1017 -3-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT

25、PERMISSION FROM ULUL, in performing its functions in accordance with its objectives, does not guarantee or warrant thecorrectness of Certification Requirement Decisions it may issue or that they will be recognized or adoptedby anyone. Certification Requirement Decisions are the opinion of Underwrite

26、rs Laboratories Inc. inpractically applying the requirements of the standard. They do not represent formal interpretations of thestandard under American National Standards Institute (ANSI) processes. UL shall not be responsible toanyone for the use of or reliance upon Certification Requirement Decis

27、ions by anyone. UL shall not incurany obligation or liability for damages, including consequential damages, arising out of or in connectionwith the use or reliance upon Certification Requirement Decisions. The electronic version of theCertification Requirement Decision is the current version and previously printed copies may be outdated.This document is published as a service to ULs certification customersSTANDARD NUMBER: UL 1017 -4-