UL 2200 CRD-2012 UL Standard for Safety Stationary Engine Generator Assemblies - Section Paragraph Reference 35 2 (Edition 2 June 01 2012)《固定发动机发电组件的UL安全标准 节 段落参考 35 2 (第二版 2012年6.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUNDERWRITERS LABORATORIES CERTIFICATION REQUIREMENT DECISIONThis Certification Requirement Decision is prepared and published by Underwriters Laboratories Inc.(UL). It is normative for the applic

2、able UL Product Certification Program(s); however, it is currently notpart of the UL Standard(s) referenced below.Product Category (CCN): FTSRStandard Number: UL 2200Edition Date: June 1, 2012Edition Number: 2Section / Paragraph Reference: 35.2DECISION:Low pressure propane and natural gas flexible h

3、oses will be subjected to the following tests.Volume Change and Extraction Test for hose materials not evaluated to UL 21. (Not conducted on metalflexible fuel hoses)PULL TEST: (As Received)Three samples of the fuel hose assembly (hose and end fittings) are to be tested. Each sample wasmounted in a

4、tensile strength testing machine and subjected to a gradually increasing load until failureoccurs. The samples shall withstand at least a 60 lb. pullout force.AGING TEST: (Not conducted on metal flexible fuel hoses)Three representative samples of the fuel hose assembly are to be subjected to 70 h in

5、 an air-circulatingoven maintained at a temperature of 100C (212F). The samples were subjected to a pull test before andafter aging and the test samples shall not show signs of deterioration or loss of flexibility after aging.PULL TEST: (After Aging)The three samples of the fuel hose assembly (hose

6、and end fittings), which were subjected to the Agingtest, are to be used for this test. Each sample was mounted in a tensile strength testing machine andsubjected to a gradually increasing load until failure occurs. The samples shall maintain at least 70percent of their longitudinal pull strength an

7、d withstand at least a 60 lb. pullout force.VIBRATION TEST:Two samples of the hose assembly are to be subjected to while pressurized to normal operating pressure.The two samples were prepared one in the horizontal position, the other in the vertical, both with one endfixed. They were mounted on the

8、vibration machine and subjected to 48 h vibration of 0.125 in. amplitudeat a frequency of 17 Hz. During and following the test the samples shall withstand the vibration withoutshowing signs of degradation or leakage.AEROSTATIC LEAKAGE TEST:Three samples of 18-inch long flexible hose assemblies are t

9、o be subjected to this test. Each sample isto have one end of the assembly plugged and the other hose end pressurized to 1.5 times operatingpressure for 5 minutes, while being immersed in water and checked for leakage.HYDROSTATIC STRENGTH TEST:UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRO

10、DUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULThree samples of 18-inch long flexible hose assemblies are to be subjected to this test. Each sample isto have on e end plugged and the other hose end is to be hydrostatically pressurized to 4 times operatingpressure for 1 minute and checked for leaka

11、ge.RATIONALE FOR DECISION:These requirements are being documented to maintain consistency between evaluations and are basedin part on the evaluation and test criteria used in cleaning machines fueled by low pressure propane.Copyright 2012 Underwriters Laboratories Inc.UL, in performing its functions

12、 in accordance with its objectives, does not guarantee or warrant thecorrectness of Certification Requirement Decisions it may issue or that they will be recognized or adoptedby anyone. Certification Requirement Decisions are the opinion of Underwriters Laboratories Inc. inpractically applying the r

13、equirements of the standard. They do not represent formal interpretations of thestandard under American National Standards Institute (ANSI) processes. UL shall not be responsible toanyone for the use of or reliance upon Certification Requirement Decisions by anyone. UL shall not incurany obligation

14、or liability for damages, including consequential damages, arising out of or in connectionwith the use or reliance upon Certification Requirement Decisions. The electronic version of theCertification Requirement Decision is the current version and previously printed copies may be outdated.This document is published as a service to ULs certification customersSTANDARD NUMBER: UL 2200 -2-