UL SUBJECT 2441-2003 OUTLINE OF INVESTIGATION FOR COMPONENT - CONNECTOR HOUSINGS (Issue 1)《部件连接器外壳调查大纲 发布编号 1》.pdf

1、October 3, 20031SUBJECT 2441OUTLINE OF INVESTIGATIONFORCOMPONENT - CONNECTOR HOUSINGSIssue Number 1October 3, 2003Summary of TopicsThis first issue of the Subject 2441 Outline of Investigation forComponent-Connector Housings covers single and multi-pole insulatinghousings without electrical contacts

2、 intended for factory assembly tocontacts (pins) by the end use manufacturer.COPYRIGHT 2003 UNDERWRITERS LABORATORIES INC.OCTOBER 3, 2003SUBJECT 24412No Text on This PageCONTENTSFOREWORD 4INTRODUCTION1 Scope .52 Glossary .53 Components 64 Units of Measurement .65 References .6CONSTRUCTION6 General 6

3、PERFORMANCE7 General 7MARKING8 General 7APPENDIX AStandards for ComponentsA1OCTOBER 3, 2003 SUBJECT 2441 3FOREWORDA. This Outline of Investigation contains basic requirements for products covered by UnderwritersLaboratories Inc. (UL) under its Follow-Up Service for this category within the limitatio

4、ns given below andin the Scope section of this Outline of Investigation. They are subject to revision as further experience andinvestigation may show is necessary or desirable.B. The observance of these requirements by a manufacturer is one of the conditions of the continuedcoverage of the manufactu

5、rers product.C. A product which complies with the text of this Outline of Investigation will not necessarily be judged tocomply with the Outline of Investigation if, when examined and tested, it is found to have other featureswhich impair the level of safety contemplated by these requirements.D. A p

6、roduct employing materials or having forms of construction which conflict with specific requirementsof the Outline of Investigation cannot be judged to comply with the Outline of Investigation. A productemploying materials or having forms of construction not addressed by this Outline of Investigatio

7、n may beexamined and tested according to the intent of the requirements and, if found to meet the intent of thisOutline of Investigation, may be judged to comply with the Outline of Investigation.E. UL, in performing its functions in accordance with its objectives, does not assume or undertake todis

8、charge any responsibility of the manufacturer or any other party. The opinions and findings of ULrepresent its professional judgement given with due consideration to the necessary limitations of practicaloperation and state of the art at the time the Outline of Investigation is processed. UL shall n

9、ot beresponsible to anyone for the use of or reliance upon this Outline of Investigation by anyone. UL shall notincur any obligation or liability for damages, including consequential damages, arising out of or inconnection with the use, interpretation of, or reliance upon this Outline of Investigati

10、on.F. Many tests required by the Outline of Investigations of UL are inherently hazardous and adequatesafeguards for personnel and property shall be employed in conducting such tests.OCTOBER 3, 2003SUBJECT 24414INTRODUCTION1 Scope1.1 These requirements cover single and multi-pole insulating housings

11、 without electrical contacts. Theyare intended for factory assembly to contacts (pins) by the end use manufacturer and are evaluated usingthe material construction requirements of the end use product.1.2 This outline supplements the following:a) Connector housings for assembly onto flexible cord or

12、cable that are covered by theStandard for Cord Sets and Power-Supply Cords, UL 817;b) Connector housings for use with attachment plugs, cord connectors, receptacles, inlets, andoutlets, that are covered by the Standard for Attachment Plugs and Receptacles, UL 498;c) Connector housings for use with w

13、ire connectors and soldering lugs that are covered by theStandards for Wire Connectors For Use With Copper Conductors, UL 486A; Splicing WireConnectors, UL 486C; or Equipment Wiring Terminals, UL 486E;d) Connector housings for use with quick-connect terminals that are covered by the Standardfor Quic

14、k Connect Terminals, UL 310.e) Connector housings for use with component connectors that are covered by the Standard forComponent Connectors for Use in Data, Signal, Control and Power Applications, UL 1977.2 Glossary2.1 For the purpose of this Outline the following definitions apply.2.2 CONTACTS (PI

15、NS) A conductive element intended to mate with a corresponding element toprovide an electrical path.2.3 CONNECTOR HOUSING (INSULATOR) The molded insulating portion of a wiring harness,connector or similar device that provides for separation and support of contacts.OCTOBER 3, 2003 SUBJECT 2441 53 Com

16、ponents3.1 Except as indicated in 3.2, a component of a product covered by this Outline of Investigation shallcomply with the requirements for that component. See Appendix A for a list of standards coveringcomponents used in the products covered by this Outline of Investigation.3.2 A component is no

17、t required to comply with a specific requirement that:a) Involves a feature or characteristic not required in the application of the component in theproduct covered by this Outline of Investigation, orb) Is superseded by a requirement in this Outline of Investigation.3.3 A component shall be used in

18、 accordance with its rating established for the intended conditions ofuse.3.4 Specific components are incomplete in construction features or restricted in performance capabilities.Such components are intended for use only under limited conditions, such as certain temperatures notexceeding specified

19、limits, and shall be used only under those specific conditions.4 Units of Measurement4.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory orapproximate information.5 References5.1 Any undated reference to a code or standard appearing in the requirements of

20、 this Outline ofInvestigation shall be interpreted as referring to the latest edition of that code or standard.CONSTRUCTION6 General6.1 Connector housings shall comply with the material requirements for one or more of the specified endproduct categories where the acceptability of the combination is

21、to be determined.6.2 The acceptability of a connector housing in any particular application depends on its ability to be usedunder the conditions that prevail in actual service. For a particular application, a connector housing maybe affected by the requirements for the equipment in which it is used

22、, and it may be necessary toadditionally evaluate features or performance characteristics that are not specified in this Outline ofInvestigation.6.3 The flame class rating, if specified, of the material shall be judged at the minimum thicknessemployed at the walls and barriers in the connector housi

23、ng which are critical to the functioning of theinsulation.OCTOBER 3, 2003SUBJECT 24416PERFORMANCE7 General7.1 The performance of assembled devices, connector housing and contacts, shall be investigated bysubjecting representative devices in commercial form to the applicable tests specified in the en

24、d productcategories.MARKING8 General8.1 A device shall be legibly marked, where visible before installation, with the manufacturers tradename, trademark, or other descriptive marking by which the organization responsible for the product maybe identified.8.2 The following shall be marked on the devic

25、e or on the smallest unit container or carton or on a stuffersheet in the smallest unit container or carton:a) The catalog number or an equivalent designation; andb) Flammability class, if specified.8.3 If the same device is produced or assembled at more than one factory, each finished device shallh

26、ave a distinctive marking, which may be in code, to identify the factory of origin.Exception: If the product is of a size such that legibility of the factory code designation would be difficultto attain, or if the construction or manufacturing process does not permit a legible factory code designati

27、onon each finished device, then the factory marking may instead be provided on the smallest unit containeror carton.OCTOBER 3, 2003 SUBJECT 2441 7OCTOBER 3, 2003SUBJECT 24418No Text on This PageAPPENDIX AStandards for ComponentsStandards under which components of the products covered by this Outline

28、 of Investigation are evaluatedinclude the following:Title of Standard UL Standard DesignationFlammability of Plastic Materials for Parts in Devices & Appliances, Tests for UL 94Polymeric Materials - Short Term Property Evaluation UL 746APolymeric Materials - Long Term Property Evaluation UL 746BPolymeric Materials - Use in Electrical Equipment Evaluations UL746COCTOBER 3, 2003 SUBJECT 2441 A1OCTOBER 3, 2003SUBJECT 2441A2No Text on This Page