IEC 61188-5-3-2007 Printed boards and printed board assemblies - Design and use - Part 5-3 Attachment (land joint) considerations - Components with gull-wing le.pdf

1、 IEC 61188-5-3 Edition 1.0 2007-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Printed boards and printed board assemblies Design and use Part 5-3: Attachment (land/joint) considerations Components with gull-wing leads on two sides Cartes imprimes et cartes imprimes quipes Conception et utilisation

2、Partie 5-3: Considrations sur les liaisons pistes-soudures Composants sorties en aile de mouette sur deux cts IEC 61188-5-3:2007 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reprodu

3、ced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaini

4、ng additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soi

5、t et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication,

6、utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organizati

7、on that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment m

8、ight have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.i

9、ec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more t

10、han 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further as

11、sistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce

12、 qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publ

13、ications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Publish

14、ed CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes l

15、ectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.ht

16、m Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61188-5-3 Edition 1.0 2007-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Printed b

17、oards and printed board assemblies Design and use Part 5-3: Attachment (land/joint) considerations Components with gull-wing leads on two sides Cartes imprimes et cartes imprimes quipes Conception et utilisation Partie 5-3: Considrations sur les liaisons pistes-soudures Composants sorties en aile de

18、 mouette sur deux cts INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE U ICS 31.180 PRICE CODE CODE PRIX ISBN 2-8318-1060-5 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 61188-

19、5-3 IEC:2007 CONTENTS FOREWORD.4 INTRODUCTION.6 1 Scope.7 2 Normative references .7 3 General information7 3.1 General component description .7 3.2 Marking .7 3.3 Carrier packaging format.7 3.4 Process considerations .7 4 TSOP (Type 1) .8 4.1 Field of application 8 4.2 Component description8 4.3 Com

20、ponent dimensions .8 4.4 Solder joint fillet design .9 4.5 Land pattern dimensions .11 5 TSOP (Type 2) .13 5.1 Field of application 13 5.2 Component description13 5.3 Component dimensions .13 5.4 Solder joint fillet design .14 5.5 Land pattern dimensions .16 6 SOP .18 6.1 Field of application 18 6.2

21、 Component description18 6.3 Component dimensions .18 6.4 Solder joint fillet design .19 6.5 Land pattern dimensions .21 7 SSOP .23 7.1 Field of application 23 7.2 Component description23 7.3 Component dimensions .24 7.4 Solder joint fillet design .24 7.5 Land pattern dimensions .26 Bibliography29 F

22、igure 1 TSOP (Type 1) construction.8 Figure 2 TSOP (Type 1) Component dimensions.9 Figure 3 Solder joint fillet design (see IEC 61188-5-1, Tables 2 and 3) 11 Figure 4 TSOP (Type 1) Land pattern dimensions.13 Figure 5 TSOP (Type 2) construction.13 Figure 6 TSOP (Type 2) Component dimensions.14 Figure

23、 7 Solder joint fillet design (see IEC 61188-5-1, Tables 2 and 3) 16 Figure 8 TSOP (Type 2) Land pattern dimensions.18 Figure 9 SOPIC construction18 Figure 10 SOP component dimensions 19 61188-5-3 IEC:2007 3 Figure 11 Solder joint fillet design (see IEC 61188-5-1, Table 2)21 Figure 12 SOP Land patte

24、rn dimensions23 Figure 13 SSOP construction.23 Figure 14 Component dimensions24 Figure 15 Solder joint fillet design (see IEC 61188-5-1, Table 2)26 Figure 16 Land pattern dimensions 28 4 61188-5-3 IEC:2007 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ PRINTED BOARDS AND PRINTED BOARD ASSEMBLIES DESIGN

25、 AND USE Part 5-3: Attachment (land/joint) considerations Components with gull-wing leads on two sides FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The ob

26、ject of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specificat

27、ions (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations lia

28、ising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters expre

29、ss, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committ

30、ees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National

31、 Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no mar

32、king procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servan

33、ts or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication

34、, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility t

35、hat some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61188-5-3 has been prepared by IEC technical committee 91: Electronics assembly technology. The text of th

36、is standard is based on the following documents: FDIS Report on voting 91/702/FDIS 91/734/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This bilingual version, published in 2009-09, corresponds to the English v

37、ersion. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 61188-5-3 IEC:2007 5 IEC 61188-5-3 is to be read in conjunction with IEC 61188-5-1. The French version of this standard has not been voted upon. A list of all parts of the IEC 61188 series, under the general

38、 title Printed boards and printed board assemblies Design and use, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related

39、to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. 6 61188-5-3 IEC:2007 INTRODUCTION This part of IEC 61188 covers land patterns for components with gull-wing leads on two sides. Each clause contains information in ac

40、cordance with the following format: The proposed land pattern dimensions in this standard are based upon the fundamental tolerance calculation combined with the given land protrusions and courtyard excesses (see IEC 61188-5-1, Generic requirements). The courtyard includes all issues of the normal ma

41、nufacturing necessities. The unaltered land pattern dimensions of this part are generally applicable for the solder paste application plus reflow soldering process. For application of the wave soldering process, the land pattern dimensions normally have to be modified. Orientation parallel to the wa

42、ve direction is preferable and special, suitably dimensioned solder thieves should be added. This standard offers a threefold land pattern dimensioning (levels 1, 2, and 3) on the basis of a threefold set of land protrusions and courtyard excesses: maximum (max.); median (mdn) and minimum (min.). Ea

43、ch land pattern has been assigned an identification number to indicate the characteristics of the specific robustness of the land patterns. Users also have the opportunity to organize the information so that it is most useful for their particular design. If a user has good reason to use a concept di

44、fferent from that of IEC 61188-5-1 or if the user prefers unusual land protrusions, this standard should be used for checking the resulting solder fillet size. It is the responsibility of the user to verify the SMD land patterns used for achieving an undisturbed mounting process including testing an

45、d an ensured reliability for the product stress conditions in use. Component dimensions listed in this standard are those available on the market and regarded as for reference only. 61188-5-3 IEC:2007 7 PRINTED BOARDS AND PRINTED BOARD ASSEMBLIES DESIGN AND USE Part 5-3: Attachment (land/joint) cons

46、iderations Components with gull-wing leads on two sides 1 Scope This part of IEC 61188 provides information on land pattern geometries used for the surface attachment of electronic components with gull-wing leads on two sides. The intent of the information presented herein is to provide the appropri

47、ate size, shape and tolerances of surface mount land patterns to ensure sufficient area for the appropriate solder fillet, and also allow for inspection, testing and reworking of those solder joints. Each clause contains a specific set of criteria such that the information presented is consistent, p

48、roviding information on the component, the component dimensions, the solder joint design, and the land pattern dimensions. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undat

49、ed references, the latest edition of the referenced document (including any amendments) applies. IEC 61188-5-1:2002, Printed boards and printed board assemblies Design and use Part 5- 1: Attachment (land/joint) considerations Generic requirements 3 General information 3.1 General component description The acronyms TSOP (thin small outline pack