IEEE 1613 1-2013 en Environmental and Testing Requirements for Communications Networking Devices Installed in Transmission and Distribution Facilities《输配电设施中安装的.pdf

1、 IEEE Standard Environmental and Testing Requirements for Communications Networking Devices Installed in Transmission and Distribution Facilities Sponsored by the Substations Committee and the Transmission and Distribution Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Power and Energ

2、y SocietyIEEE Std 1613.1-2013IEEE Std 1613.1-2013 IEEE Standard Environmental and Testing Requirements for Communications Networking Devices Installed in Transmission and Distribution Facilities Sponsor Substations Committee Co-Sponsor Transmission and Distribution Committee of the IEEE Power and En

3、ergy Society Approved 11 December 2013 IEEE-SA Standards Board Abstract: Environmental testing requirements are defined for communications networking devices to be installed in transmission and distribution facilities. This standard establishes a common reproducible basis for designing and evaluatin

4、g devices utilizing radio frequency (RF) up to 6 GHz, power line communications, and broadband over power line (BPL) technologies. It also requires immunity to five IEC electromagnetic compatibility standards for which there are no IEEE equivalent standards. This standard is an extension to IEEE Std

5、 1613-2009 and IEEE Std 1613a-2011. Keywords: common-mode disturbances, communications networking device, conducted RF, damped oscillatory magnetic fields, IEEE 1613.1, immunity, power frequency magnetic fields, radiated, RFI hazards, surge The Institute of Electrical and Electronics Engineers, Inc.

6、 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2013 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 20 December 2013. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non

7、infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntar

8、y. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject t

9、o change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertakin

10、g to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in

11、 determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTER

12、RUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUC

13、H DAMAGE WAS FORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Copyright 2013 IEEE. All right

14、s reserved. ivOfficial statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon

15、 as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on st

16、andards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in t

17、he form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the m

18、embers of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to

19、 participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents shoul

20、d consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE do

21、es not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made ava

22、ilable by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use a

23、nd adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizatio

24、nal internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational clas

25、sroom use can also be obtained through the Copyright Clearance Center. Copyright 2013 IEEE. All rights reserved. vUpdating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amende

26、d from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every

27、ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest editio

28、n of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed prev

29、iously. For more information about the IEEE SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html

30、 Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the exis

31、tence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of As

32、surance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essent

33、ial Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensin

34、g terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of su

35、ch rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. Copyright 2013 IEEE. All rights reserved. viParticipants At the time this draft standard was completed, the PES Substations C2 Working Group had the following membership: John Te

36、ngdin, Co-Chair G. Larry Clark, Co-Chair Gerald Ramie, Vice Chair Krista Gluchoski, Secretary John Banting James Bougie Didier Chan-Foy Bui Dac-phoue Michael J. Dood Ron Farquharson Richard Harada Chris Huntley Marc Lacroix Alex Lee Brian Mugalian Jay Murphy Daniel Nordell Arnold Offner Craig Preuss

37、 Mark Simon Tyler Stinson Eric Thibodeau Jian-Chang Tan The following members of the individual balloting committee voted on this standard. Balloters may have voted for approval, disapproval, or abstention. William Ackerman Saleman Alibhay John Banting Paul Barnhart Philip Beaumont Robert Beresh Osc

38、ar Bolado James Bougie Gustavo Brunello William Byrd Thomas Callsen Paul Cardinal Didier Chan-Foy Suresh Channarasappa Robert Christman Stephen Conrad Randall Crellin Michael J. Dood John Egan Kenneth Fodero Fredric Friend Jalal Gohari Stephen Grier Randall Groves Roger Hedding Jeffrey Helzer Lee He

39、rron Gary Heuston Werner Hoelzl Yi Hu Chris Huntley Noriyuki Ikeuchi Gael Kennedy Yuri Khersonsky Jim Kulchisky Marc Lacroix Chung-Yiu Lam Thomas McCarthy William Mccoy John McDonald Jose Morales Brian Mugalian Jerry Murphy R. Murphy Bruce Muschlitz Michael Newman Joe Nims Gary Nissen Lorraine Padde

40、n Bansi Patel Percy Pool Craig Preuss Farnoosh Rahmatian Michael Roberts Charles Rogers Benjamin Rolfe Thomas Rozek Sergio Santos Bartien Sayogo Dennis Schlender Thomas Schossig Devki Sharma Mark Simon Veselin Skendzic Jerry Smith John Spare Gary Stoedter Gary Stuebing John Tengdin Joe Uchiyama Eric

41、 Udren Benton Vandiver John Vergis Jane Verner James Wilson Daidi Zhong Sergio Zimath Copyright 2013 IEEE. All rights reserved. viiWhen the IEEE-SA Standards Board approved this standard on 11 December 2013, it had the following membership: John Kulick, Chair David J. Law, Vice Chair Richard H. Hule

42、tt, Past Chair Konstantinos Karachalios, Secretary Masayuki Ariyoshi Peter Balma Farooq Bari Ted Burse Wael William Diab Stephen Dukes Jean-Philippe Faure Alexander Gelman Mark Halpin Gary Hoffman Paul Houz Jim Hughes Michael Janezic Joseph L. Koepfinger* Oleg Logvinov Ron Petersen Gary Robinson Jon

43、 Walter Rosdahl Adrian Stephens Peter Sutherland Yatin Trivedi Phil Winston Yu Yuan *Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board liaisons: Richard DeBlasio, DOE Representative Michael Janezic, NIST Representative Catherine Berger Senior Program Manager, IEEE-SA

44、Content Publishing Erin Spiewak Program Manager, IEEE-SA Technical Community Copyright 2013 IEEE. All rights reserved. viiiIntroduction This introduction is not part of IEEE Std 1613.1-2013, IEEE Standard Environmental and Testing Requirements for Communications Networking Devices Installed in Trans

45、mission and Distribution Facilities. This document is an extension of IEEE Std 1613-2009 and its amendment (IEEE Std 1613a-2011) from two perspectives. The scope has been broadened to include devices installed in all electric power facilities, not just substations, and includes the communications mo

46、dules installed in Smart Meters. It adds two installation zones(Zone A) inside a facilitys building/control house or fenced area, and (Zone B) outside these buildings or fenced areas. Thus, it is expressly applicable for devices used for distribution automation and distributed generation. Added are

47、the device testing and performance requirements for communications via radio frequency (RF), via power line carrier/communications, via Broadband over Power Line (BPL), or via Ethernet cable. Five IEC immunity tests have also been added as suggested in the SGIP-EMI Issues White paper B5awith specifi

48、c immunity levels for Zone A and Zone B installations. The test conditions and acceptance criteria in Annex A have been revised to help ensure that the transmit function of the device is exposed to the test conditions at some point during the tests in Clause 5 through Clause 12. This is a new requir

49、ement in this text, and may not be a requirement in other standards. The requirements in Clause 6 of IEEE Std 1613-2009 regarding the application of the fast transient (EFT) test waveform for transverse mode testing of a devices input/output circuits have been deleted. Transverse mode testing for EFT is only required on dc power supply terminals rated 48 volts or above. Other than these changes and the reduced test levels in Zone B, all the remaining requirements in IEEE Std 1613-2009 are unchanged, and are applicable to IEEE 1613.1 devices. The reverse is a