ISO 13399-1 AMD 1-2010 Cutting tool data representation and exchange - Part 1 Overview fundamental principles and general information model Amendment 1《切削工具数据表示.pdf

1、 Reference number ISO 13399-1:2006/Amd.1:2010(E) ISO 2010INTERNATIONAL STANDARD ISO 13399-1 First edition 2006-02-15 AMENDMENT 1 2010-05-01 Cutting tool data representation and exchange Part 1: Overview, fundamental principles and general information model AMENDMENT 1 Reprsentation et change des don

2、nes relatives aux outils coupants Partie 1: Vue densemble, principes fondamentaux et modle gnral dinformations AMENDEMENT 1 ISO 13399-1:2006/Amd.1:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but s

3、hall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this are

4、a. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use b

5、y ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any

6、 form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749

7、 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedISO 13399-1:2006/Amd.1:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member b

8、odies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental a

9、nd non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives

10、, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies ca

11、sting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Amendment 1 to ISO 13399-1:2006 was prepared by Technical Committee ISO/TC 29, Small to

12、ols. ISO 13399-1:2006/Amd.1:2010(E) ISO 2010 All rights reserved 1Cutting tool data representation and exchange Part 1: Overview, fundamental principles and general information model AMENDMENT 1 Page 6, 5.1.2 Add the following application object as the first indent: fitting_bounds Page 14, 5.2.11 Re

13、place the EXPRESS specification with the following: EXPRESS specification: TYPE limitation_definition_select = SELECT (limits_and_fits, plus_minus_bounds, fitting_bounds); END_TYPE; Page 21, 5.2.26 Add the following definition below the title. A coating is an applied material layer or layers deposit

14、ed on a substrate. Add the following subclauses. 5.2.26.1 coating_name A coating_name is a name by which the coating is referred to. 5.2.26.2 coating_process A coating_process is a process by which the coating has been applied. ISO 13399-1:2006/Amd.1:2010(E) 2 ISO 2010 All rights reservedPage 42, 5.

15、2.58 Replace this subclause with the following: 5.2.58 grade A grade is a label for the final composition of the cutting item material substrate or substrate and coating. 5.2.58.1 coating The coating specifies the coating of the grade. 5.2.58.2 cutting_condition The cutting_condition specifies the r

16、elevant cutting conditions for the grade. 5.2.58.3 identifier This is an identifier for the grade. 5.2.58.4 standard_designation A standard_designation is a designation for the grade based on a standard. 5.2.58.5 substrate The substrate specifies the substrate of the grade. 5.2.58.6 workpiece_materi

17、al The workpiece_material specifies workpiece materials that are suitable for machines using the grade. Page 43, 5.2.60 Replace the first paragraph with the following: 5.2.60 item An item is either a single object or a unit in a group of objects. It collects the information that is common to all ver

18、sions of the object. An item shall always be classified as cutting item, tool item, adaptive item, or assembly item using a specific_item_classification. Additionally, if an assembly_definition exists for at least one version of the item, the item shall be classified as being an assembly using speci

19、fic_item_classification. Page 44, 5.2.61 Replace this subclause with the following: 5.2.61 item_characteristic_association An item_characteristic_association associates a characteristic to an item_definition. ENTITY item_characteristic_association; associated_characteristic : item_characteristic_sel

20、ect; associated_item : item_definition; relation_type : OPTIONAL STRING; END_ENTITY; ISO 13399-1:2006/Amd.1:2010(E) ISO 2010 All rights reserved 3Add the following subclause. 5.2.61.3 relation_type The relation_type specifies the meaning of the relationship. Where applicable, the following values sh

21、all be used: has characteristic: The relationship indicates that the item possesses the related characteristic. is related to: The relationship indicates that the item is related to the characteristic. used for: The relationship indicates that the item may be used in the context of the related chara

22、cteristic. Page 44, 5.2.62 Replace this subclause with the following: 5.2.62 item_definition An item_definition is a view of an item_version. This view is relevant for the requirements of one or more application domains and collects product data of the item_version. NOTE The selection of data descri

23、bing an item_version can be different for assembly purposes, shipping purposes or analysis purposes. Each item_definition may be a mating_definition, an assembly_definition, or a physical_item_definition. EXPRESS specification: ENTITY item_definition SUPERTYPE OF (ONEOF(assembly_definition, mating_d

24、efinition, physical_item_definition); associated_item_version : item_version; contexts : OPTIONAL SET OF application_context; id : STRING; name : OPTIONAL string_select; END_ENTITY; Page 44, 5.2.62.1 Replace this subclause with the following: 5.2.62.1 contexts The contexts specifies the set of appli

25、cation_context objects in which this view of the item_version is relevant. Page 44, delete 5.2.62.4 ISO 13399-1:2006/Amd.1:2010(E) 4 ISO 2010 All rights reservedPage 50, 5.2.70 Add the following definition below the title. A location is a place or position where a product or resource can exist. Add

26、the following subclauses. 5.2.70.1 location_id A location_id is an identifier of the location. 5.2.70.2 location_name A location_name is the word or group of words by which the location is known. 5.2.70.3 location_type The location_type specifies the type of location. Where applicable, the following

27、 values shall be used: warehouse: The location is a warehouse. turret: The location is a tool turret. room: The location is a room. machine: The location is a machine tool. Page 57, 5.2.84 Add the following definition below the title. A physical_item is a type of item that identifies an individual a

28、rtefact that has been made. It is a collector of data common to all revisions of the physical_item. Page 57, 5.2.85 Add the following definition below the title. A physical_item_location_association is a relationship that allows a physical_item_definition to have a location. Add the following subcla

29、uses. 5.2.85.1 located_item The located_item attribute specifies the physical_item that is being located. 5.2.85.2 location The location attribute specifies the location object. Page 57, 5.2.86 Add the following definition below the title. A physical_item_definition is a type of item_definition that

30、 defines a characterization view of a version of a physical_item. ISO 13399-1:2006/Amd.1:2010(E) ISO 2010 All rights reserved 5NOTE The physical_item_definition entity type supports the representation of different views of a physical_item for different purposes. Multiple views of the same physical_i

31、tem are represented by different instances of physical_item_definition for the same physical_item_version. Page 57, 5.2.87 Add the following definition below the title. A physical_item_state_association is a relationship that allows a physical_item_definition to have state or to be in a state. Add t

32、he following subclauses. 5.2.87.1 associated_physical_item The associated_physical_item specifies the physical_item_definition which has a state. 5.2.87.2 associated_state The associated_state specifies the state which is being assigned. 5.2.87.3 role The role specifies the role of the physical_item

33、_state_association. Where applicable, the following values shall be used: observed: The associated state is an actual observed state. predicted: The associated state is a predicted state, it may or may not be true. Page 57, 5.2.88 Add the following definition below the title. A physical_item_structu

34、re_association creates a parent child relationship between physical_item_definitions. NOTE The relationship relates physical_items at the physical_item_definition level since a single physical_item (a single solid body which you can touch) can have multiple functions with their own assembly of compo

35、nents. EXAMPLE A multi-function tool which has three different functions on the same tool body, each function having its own insert and clamping system. Add the following subclauses. 5.2.88.1 related The related attribute specifies the child of the relationship. 5.2.88.2 relating The relating attrib

36、ute specifies the parent of the relationship. Page 58, 5.2.89 Add the following definition below the title. A physical_item_version is a type of item_version that identifies a revision of an individual artefact that has been made. An item whose properties can only be known by observation, or by deri

37、vation from observations. ISO 13399-1:2006/Amd.1:2010(E) 6 ISO 2010 All rights reservedNOTE The physical_item_version represents the physical product, something one can touch. Page 65, 5.2.100 Add the following definition below the title. A realized_item_association is a relationship between a produ

38、ct, represented by an item, and the product that has been made, represented by a physical_item_version. Add the following subclauses. 5.2.100.1 physical_item The physical_item attribute specifies the physical_item that is a realization of the item_version. 5.2.100.2 realized_item_version The realize

39、d_item_version attribute specifies the item_version object of which the physical_item is a realization. Page 67, 5.2.104 Add the following definition below the title. A state is the mode of being in which something does or could exist for a period of time. Add the following subclause. 5.2.104.1 name

40、 The name specifies the name by which the state is known. Page 68, 5.2.107 Add the following definition below the title. A substrate is the main material composition of a cutting item. Add the following subclause. 5.2.107.1 name This is the name by which the substrate is referred to. ISO 13399-1:200

41、6/Amd.1:2010(E) ISO 2010 All rights reserved 7Page 68, 5.2.108 Replace this subclause with the following: 5.2.108 Transformation A transformation is a geometric transformation composed of translation and rotation. Scaling is not included. Each transformation is a transformation_3d or a transformatio

42、n_2d. EXPRESS specification: ENTITY transformation ABSTRACT SUPERTYPE OF (ONEOF(transformation_2d, transformation_3d); axis_1 : OPTIONAL direction; axis_2 : OPTIONAL direction; local_origin : cartesian_point; END_ENTITY; Add the following subclauses. 5.2.108.1 axis_1 Axis_1 is the direction used to

43、determine the derived X-axis direction. 5.2.108.2 axis_2 Axis_2 is the direction used to determine the derived Y-axis direction. 5.2.108.3 local_origin The local_origin is the required translation, specified as a cartesian point. The actual translation included in the transformation is from the geom

44、etric origin to the local origin. Page 68, 5.2.110 Replace this subclause with the following: 5.2.110 transformation_3d A transformation_3d is the definition of a geometric transformation in 3D space. A transformation_3d is a type of transformation. EXPRESS specification: ENTITY transformation_3d SU

45、BTYPE OF (transformation); axis_3 : OPTIONAL direction; END_ENTITY; ISO 13399-1:2006/Amd.1:2010(E) 8 ISO 2010 All rights reservedAdd the following subclause. 5.2.110.1 axis_3 Axis_3 is the direction used to determine the derived Z-axis direction. Page 72, after 5.2.117 Add the following new subclaus

46、es. 5.2.118 fitting_bounds A fitting_bounds is the specification of the allowable deviation from a numerical value for a fitting. EXPRESS specification: ENTITY fitting_bounds; lower_bound : STRING; significant_digits : OPTIONAL STRING; upper_bound : STRING; value_determination : OPTIONAL STRING; END

47、_ENTITY; 5.2.118.1 lower_bound The lower_bound specifies the value of the tolerance that shall be subtracted or added from the exact value to establish the minimum allowed value. 5.2.118.2 significant_digits The significant_digits specifies the number of decimal digits indicating the accuracy of the

48、 lower_bound and upper_bound values. The significant_digits need not be specified for a particular fitting_bounds. 5.2.118.3 upper_bound The upper_bound specifies the value of the tolerance that shall be added or subtracted to the exact value to establish the maximum allowed value. 5.2.118.4 value_d

49、etermination The value_determination specifies information on how the fitting_bounds shall be interpreted. The value_determination need not be specified for a particular fitting_bounds. Where applicable, the following values shall be used: calculated: The value has been calculated; designed: The value represents a value intended by the design; estimated: The value has been estimated; measured: The value has been measured; required: The value represents a requ