EN 16842-2-2018 Powered industrial trucks - Visibility - Test methods and verification - Part 2 Sit-on counterbalance trucks and rough terrain masted trucks up .pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Powered industrial trucks - Visibility - Test methods and verificationPart 2: Sit-on counterbalance trucks and rough terrain masted trucks up to and including 10 000 kg capacityBS EN 16842-2:2018Incorporating corrigendu

2、m July 2018National forewordThis British Standard is the UK implementation of EN 16842-2:2018.The UK participation in its preparation was entrusted to Technical Committee MHE/7, Industrial trucks.A list of organizations represented on this committee can be obtained on request to its secretary.This p

3、ublication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 539 01712 0ICS 53.060Compliance with a British Standard cannot confer immunit

4、y from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2018.Amendments/corrigenda issued since publicationDate Text affected31 July 2018 Missing figures addedBRITISH STANDARDBS EN 16842-2:2018EUROPEAN STANDARDNORME E

5、UROPENNEEUROPISCHE NORMEN 16842-2May 2018ICS 53.060EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2018 CEN Ref. No. EN 16842-2:2018: EAll rights of exploitation in any form and by any

6、means reserved worldwide for CEN national MembersPowered industrial trucks - Visibility - Test methods and verification - Part 2: Sit-on counterbalance trucks and rough terrain masted trucks up to and including 10 000 kg capacityChariots de manutention automoteurs - Visibilit - Mthodes dessai et vri

7、fication - Partie 2 : Chariots en porte-faux conducteur assis et chariots tout terrain mt ayant une capacit jusqu 10 000 kg inclusKraftbetriebene Flurfrderzeuge - Sichtverhltnisse - Testmethoden zur Verifikation - Teil 2: Gegengewichtstapler mit Fahrersitz und gelndegngige Stapler mit Mast bis zu un

8、d einschlielich einer Nenntragfhigkeit von 10 000 kgThis European Standard was approved by CEN on 9 July 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alter

9、ation. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made

10、by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

11、 Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN 16842-

12、2:2018 (E)European foreword iiiIntroduction iv1 Scope . 52 Normative references 53 Terms and definitions . 54 Truck configuration 54.1 General . 54.2 Fork arm dimensions . 55 Test equipment. 66 Test procedures for direct visibility . 66.1 Lighting equipment position . 66.2 Test paths for trucks 1 00

13、0 kg and 5 000 kg and 5 000 kg and 10 000 kg rated capacity in Table 2.7.2.2 Travelling visibilityTable 1 and Table 2, tests 1, 2 and 10 shall apply.7.2.3 Manoeuvring visibilityTable 1 and Table 2, tests 3, 4, 5, 6, 7, 8, and 9 shall apply.7.2.4 Fork armsTable 1 and Table 2, test 11 shall apply.7.3

14、Indirect visibilityFor indirect visibility, EN 16842-1:2018, 8.4 shall apply.7.4 Criteria for trucks up to and including 5 000 kg rated capacity8 BS EN 16842-2:2018EN 16842-2:2018 (E)Table1 Requirements for trucks 5000kgTestNoTestsTestDirec-tionDistance of lights to axis of rotation (mm)NumberofLigh

15、tsTestpathTest objectRequiredminimum illuminatedarea ofthetest objectOnlyfollowing test sur-faceshall beconsidered.(See EN16842-1:2018,Figure 2) aArea of test surfaces1 xSquare = 104mm2Numberofcompleteorcombined squares on thetest bodyasperEN16842-1:2018,5.1.11TravellingForward1259P1.1 - P1.2Testbod

16、y5202Travelling+135 or- 1351259P2.1 - P2.2Testbody5203ManoeuvringForward12513P3.1 - P3.2Testbody2 + 5304Manoeuvring+ 4512513P4.1-P4.2Testbody2 + 5 + (3 or 4)12,55Manoeuvring+ 13512513P5.1-P5.2Testbody2 + 5 + (3 or 4)12,56Manoeuvring+ 13512513P6.1 - P6.2Testbody2 + 5257Manoeuvring- 13512513P7.1-P7.2T

17、estbody2 + 5258Manoeuvring- 13512513P8.1 - P8.2Testbody2 + 5 + (3 or 4)12,59Manoeuvring- 4512513P9.1-P9.2Testbody2 + 5 + (3 or 4)12,510TravellingForward1252P1.1 P1.2Testscreen5 squares of any section 500mm x 500mmb11ForkArmsDirectionofload centre125 up to 275 (see EN16842-1:2018, Figure 4)13ForkArms

18、25% of the load carrying surface of the forward half of one fork shall be illuminated. The illuminat-ed area shall be connected to the fork tip.aIf the minimum requirement is met on one surface the other surfaces need not be considered. bNot considering the dark shadows cast by vertical structural s

19、ections of the mast beams. 9BS EN 16842-2:2018EN 16842-2:2018 (E)7.5 Trucks greater than 5 000 kg and up to and including 10 000 kg rated capacity10 BS EN 16842-2:2018EN 16842-2:2018 (E)Table2 Truck 5000kg to 10000kgTestNoTestsTestDirec-tionDistance of lights to axis of rotation (mm)NumberofLightsTe

20、stpathTest objectRequired minimum illumination area of test surfaceOnly following test surface shall be considered. (See EN16842-1:2018, Figure 2.)aArea of test surfaces1 x Square = 104mm2Numberofcompleteorcombinedsquaresonthe test body as per EN16842-1:2018,5.1.1.1TravellingForward1259P1.1 - P1.2Te

21、stbody5152Travelling+135 or- 1351259P2.1 - P2.2Testbody5153ManoeuvringForward12513P3.1 - P3.2Testbody2 + 5304Manoeuvring+ 4512513P4.1-P4.2Testbody2 + 5 + (3 or 4)255Manoeuvring+ 13512513P5.1-P5.2Testbody2 + 5 + (3 or 4)256Manoeuvring+ 13512513P6.1 - P6.2Testbody2 + 5307Manoeuvring- 13512513P7.1-P7.2

22、Testbody2 + 5308Manoeuvring- 13512513P8.1 - P8.2Testbody2 + 5 + (3 or 4)259Manoeuvring- 4512513P9.1-P9.2Testbody2 + 5 + (3 or 4)2510TravellingForward1252P1.1 P1.2Testscreen5 squares of any section 500mm x 500mmb11ForkArmsDirectionofload centre125 up to 275 (see EN16842-1:2018, Figure 4)13ForkArms25%

23、 of the load carrying surface of the forward half of one fork shall be illuminated. The illuminated area shall be connected to the fork tip.aIf the minimum requirement is met on one surface the other surfaces need not be considered. bNot considering the dark shadows cast by vertical structural secti

24、ons of the mast beams. 11BS EN 16842-2:2018EN 16842-2:2018 (E)8 Test reportFor the test report, EN 16842-1:2018, 8.2 shall apply.9 Information for useAccording to EN ISO 3691-1:2015, 6.2.2 r), the manufacturer shall provide information in the instruction handbook(s) about operating the truck where t

25、he load or attachment can restrict visibility.To provide this information to the operator, the manufacturer should choose one of the methods described in Annex A or an equivalent method.12 BS EN 16842-2:2018EN 16842-2:2018 (E)Annex A (informative) Information for operator visibility during useA.1 Ge

26、neralThis annex describes two alternative methods provided as information for use which can be included in an operators handbook, to enable the operator to evaluate the visibility on counterbalance trucks when laden.Obstructed visibility can be caused by the dimensions and/or shape of a load on the

27、fork arms or the attachment on the truck, the operators visibility can be insufficient for safe operation. As part of the operational assessment for the truck the user may specify the operators visibility requirements for operating with a laden truck under the user specific circumstances.In addition

28、 to user specific circumstances, the following estimations can assist the user to determine when driving in the forward direction with a laden truck that the visibility is sufficient, in case of doubt the operator may drive backwards.The manufacturer may provide a statement that the user may analyse

29、 all risks associated to reduced visibility and balance the actions between the different hazards which can include: the insufficient visibility, caused by the load dimensions;and the potential adverse effects on the operator (rotation and/or sideway bending of the body).NOTE Driving backwards with

30、industrial trucks normally requires a rotated operators body position, which isnt ergonomic over a long period of time.For less potential adverse effects on the operator, the manufacturer may offer several options, e.g.: comfort seats with air suspension; seats with arm rest; rotatable operators sea

31、t and/or operating position; special-designed trucks, e.g. for beverage industry.Otherwise, the user may optimize the logistic process to minimize any potential hazards by, e.g.: correct adjustment of the seat to the operators mass; splitting of loads with large dimensions; optimizing of transport r

32、outes; sufficient breaks for operator or alternate operators on the truck during one shift; additional personnel to assist the operator.Methods 1 or 2 can assist the user and/or the operator in determining the correct procedure for transporting loads when visibility is reduced by the height of the l

33、oad.13BS EN 16842-2:2018EN 16842-2:2018 (E)A.2 Method 1Method 1 enables the user to estimate forward visibility with load by calculation, by considering the height of the load.NOTE H calculated does not change although the height of the load can change when the mast is tilted and the truck is in the

34、 travel position.KeyH calculated height of the loadH11 085 mm (70 % of the statue (with shoes) of the small operator according to EN ISO 3411:2007)H2height of the operators eyes (h7+a)h7seat height related to SIPl length of the loadl1distance between the load and the obstaclel2distance between the o

35、bstacle and the operators eyes (l1+l+x+l3)l3distance between the centre of the front axle and the SIPa 650 mm, the distance from the SIP to the operators eyesx load distance, centre of drive axle to forkNOTE 1 l + l1 = 4 000 mmNOTE 2 h7, l3and x, according to the data sheet of the manufacturer. A ma

36、nufacturer may use type sheet VDI 2198.Figure A.1 Determination of “H” by calculationA.3 Method 2Method 2 enables the user and/or the operator to estimate forward visibility by practical test with truck, load and operator to determine if forward or reverse drive direction can be used.NOTE Figure A.2

37、 indicates when a high load is on the fork arms, the rear view is better than the forward view.14 BS EN 16842-2:2018EN 16842-2:2018 (E)KeyA 1 085 mm (70 % of the statue (with shoes) of the small operator according to EN ISO 3411:2007)C load height (in travelling position)D 4 000 mm (distance, forwar

38、d from the rear corner of the load when fully engaged on the fork arms in the travel position to the obstacle)Y load in customer applicationZ operators eye positionFigure A.2 Determination of visibility using method 215BS EN 16842-2:2018EN 16842-2:2018 (E)Bibliography1 EN ISO 3411:2007, Earth-moving

39、 machinery - Physical dimensions of operators and minimum operator space envelope (ISO 3411:2007)2 VDI 2198, Type sheets for industrial trucks (Berlin, Beuth Verlag)16 BS EN 16842-2:2018This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for prepari

40、ng British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, g

41、overnment, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and a

42、cross all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Bu

43、ying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased.If you need international and foreign standards from other Standards Development Organizations,

44、 hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standar

45、dization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display th

46、e standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard

47、may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard

48、 copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money

49、 by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and ad