BS ISO 7718-1-2016 en_1828 Aircraft Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehicle Main deck doors《航空器.乘客登机桥或机场摆渡车连接用客舱门接口要求.主舱门》.pdf

1、BS ISO 7718-1:2016 Aircraft Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehicle Part 1: Main deck doors BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 7718-1:2016 BRITISH STANDARD National foreword

2、 This British Standard is the UK implementation of ISO 7718-1:2016. It supersedes BS ISO 7718-1:2009 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ACE/57, Air Cargo Figure 1 has been modified; in 4.3, minimum aircraft door sill height was increased

3、from 1,60 m (63 in) to 1,80 m (71 in); and additional editorial changes have been made, such as by adding a table of contents. A list of all parts in the ISO 7718 series can be found on the ISO website. BS ISO 7718-1:2016 ISO 7718-1:2016(E) iv ISO 2016 All rights reserved BS ISO 7718-1:2016 ISO 7718

4、-1:2016(E) Introduction This document specifies minimum requirements for dimensions and unobstructed space around main deck passenger doors on the outer skin of civil transport aircraft, applicable when these doors are designed to accept the connection of existing passenger boarding bridges or trans

5、fer vehicles. Throughout this document, the minimum essential criteria are identified by the keyword “shall”. Recommended criteria are identified by the keyword “should” and, while not mandatory, are considered to be of primary importance in providing easily and economically handled aircraft, as wel

6、l as preventing damage to the aircraft caused by the passenger boarding bridge or transfer vehicle. Deviation from recommended criteria can only occur, after careful consideration, if positively required by basic aircraft-design factors with a significant operational cost impact. ISO 2016 All rights

7、 reserved vBS ISO 7718-1:2016 Aircraft Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehicle Part 1: Main deck doors 1 Scope This document specifies minimum requirements for dimensions and unobstructed space around main deck passenger doors

8、of future types of civil-passenger transport aircraft when they are intended to be compatible with the thousands of passenger boarding bridges and passenger transfer vehicles existing, or being planned, in airports worldwide. This document is not applicable to existing models of civil transport airc

9、raft, or derivative models with entry into service up to year 2000 with the same fuselage, for which the aircraft-mating section of passenger boarding bridges or passenger transfer vehicles is expected to be compatible with ISO 16004. It is not the intent of this document to restrict in any way the

10、basic design of any future types of civil-passenger transport aircraft. However, it aims at clarifying, for aircraft-design engineers, the design characteristics which would make it difficult or impossible for a new type of aircraft to adequately connect with existing airport passenger boarding brid

11、ges or passenger transfer vehicles. If basic aircraft-design requirements impose on a future model certain dimensional characteristics not complying with this document, note that: either alternative methods of embarking/disembarking passengers will need to be implemented, such as integral aircraft s

12、tairs, etc.; or existing passenger boarding bridges and/or passenger transfer vehicles in the airports where such a new type of aircraft is to operate will require some degree of modification/reworking; or additional interface devices/equipment will be required in order to connect such a new type of

13、 aircraft with existing passenger boarding bridges and passenger transfer vehicles. Each case results in increased aircraft-handling constraints and operating cost. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes

14、requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 16004, Aircraft ground equipment Passenger boarding bridge or transfer vehicle Interface requirements wit

15、h aircraft doors 3 T erms a nd definiti ons No terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/ /www.electropedia.org/ INTERNATIONAL ST ANDARD BS ISO 7718-1:20

16、16 ISO 7718-1:2016(E) ISO 2016 All rights reserved 1 ISO Online browsing platform: available at http:/ /www.iso.org/obp 4 Requirements 4.1 Minimum unobstructed space 4.1.1 Unobstructed space shall be provided for the connection of the passenger boarding bridge or passenger transfer vehicle, as shown

17、 by the hatched area in Figure 1. The area surrounded by the dotted line represents the opening of the bridge or vehicle. 4.1.2 This area shall be kept completely clear of any external features such as aerials, drains, pitot heads, static ports, sensors, incidence probes, aerodynamic strakes, access

18、 panels, etc. 4.1.3 Integral aircraft stairs, which do not interfere with the connection of a passenger boarding bridge or passenger transfer vehicle, or with the aircraft when in the retracted position, are permitted in this area. 4.1.4 Protrusions intended to divert rainwater away from the door op

19、ening are permitted in this area, provided they are not deemed part of the aircrafts structural or aerodynamic integrity and they do not interfere with the deployment of the PBB canopy. Existing models of civil transport aircraft present a variety of flight-safety-sensitive items in the unobstructed

20、 area defined above. They shall be protected against inadvertent interference by provisions built into the aircraft mating section of passenger boarding bridges or passenger transfer vehicles in accordance with ISO 16004. The no-interference areas accordingly specified on ground equipment are includ

21、ed in the unobstructed area defined above for future aircraft. 4.2 Minimum radius of the fuselage The cross-sectional radius of the fuselage in any part of the area defined in Figure 1 should not be less than 1,6 m (63 in). 4.3 Door-sill height The passenger door sill height above the ground, at any

22、 part of its excursion range during normal airport servicing/transit operations, should be between 1,8 m (71 in) and 5,4 m (213 in). BS ISO 7718-1:2016 ISO 7718-1:2016(E) 2 ISO 2016 All rights reserved BS ISO 7718-1:2016 ISO 7718-1:2016(E) Dimensions in millimetres (inches) 1 Key 1 door sill height

23、Dimension Maximum value Minimum value Note a 2 100 (82.7) Dimension of the bridge opening b 2 850 (112.2) c 4 800 (189.0) d 500 (19.7) e 3 400 (133.8) Figure 1 Unobstructed space to be provided in the vicinity of passenger doors ISO 2016 All rights reserved 3 BS ISO 7718-1:2016 ISO 7718-1:2016(E) IS

24、O 2016 All rights reserved IC S 49.100 Price based on 3 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other sta

25、ndardization products are published by BSI Standards Limited. British Standards Institution (BSI) About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in ou

26、r standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organizatio

27、n needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through

28、our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Copyright in BSI publications All the content in BSI publications, including British St

29、andards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Save for the provisions below, you may not

30、transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent. Storing and using standards Standards purchased in

31、 soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time

32、. A single paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This in

33、cludes scanning of the document. If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions). Reproducing extracts For permission to reproduce content from BSI publications contac

34、t the BSI Copyright & Licensing team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted Eu

35、ropean and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becom

36、ing a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit

37、 With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email . Revision

38、s Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.

39、 Useful Contacts Customer Services Tel: +44 345 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 345 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK BSI Back Cover.indd 1 27/01/2016 14:20