BS ISO 7718-2-2016 en_1749 Aircraft Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehicle Upper deck doors《航空器.乘客登机桥或机.pdf

1、BS ISO 7718-2:2016 Aircraft Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehicle Part 2: Upper deck doors BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 7718-2:2016 BRITISH STANDARD National forewor

2、d This British Standard is the UK implementation of ISO 7718-2:2016. It supersedes BS ISO 7718-2:2009 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ACE/57, Air Cargo Figure 1 has been modified; additional editorial changes have been made, such as by

3、 adding a table of contents. A list of all parts in the ISO 7718 series can be found on the ISO website.iv ISO 2016 All rights reservedBS ISO 7718-2:2016ISO 7718-2:2016(E) Introduction This document specifies minimum dimensional and unobstructed space requirements around upper deck passenger doors o

4、n the outer skin of civil transport aircraft, applicable when these doors are designed to accept connection of existing passenger boarding bridges or transfer vehicles. Throughout this document, the minimum essential criteria are identified by use of the keyword “shall”. Recommended criteria are ide

5、ntified by use of the keyword “should” and, while not mandatory, are considered to be of primary importance in providing easily and economically handled aircraft, as well as preventing damage to the aircraft as a result of passenger boarding bridge interference. Deviation from recommended criteria c

6、an only occur, after careful consideration, if positively required by basic aircraft-design factors with a significant operational cost impact. ISO 2016 All rights reserved vBS ISO 7718-2:2016BS ISO 7718-2:2016Aircraft Passenger doors interface requirements for connection of passenger boarding bridg

7、e or passenger transfer vehicle Part 2: Upper deck doors 1 Scope This document specifies the minimum dimensional and unobstructed space requirements around future civil-passenger transport aircraft upper deck passenger doors when they are intended to be compatible with passenger boarding bridges pla

8、nned in airports worldwide. This document is not applicable to existing models of civil transport aircraft, or derivative models with entry into service up to year 2000 with the same fuselage, for which the aircraft-mating section of passenger boarding bridges or passenger transfer vehicles is expec

9、ted to be compatible with ISO 16004. However, it is expected that the design of such aircraft types may be taken into account for design of passenger boarding bridges capable of upper deck servicing, in addition to this document. It is not the intent of this document to restrict in any way the basic

10、 design of any future types of civil- passenger transport aircraft. It aims, however, at clarifying for aircraft design engineers the design characteristics which would make it difficult or impossible for a new type of aircraft to adequately connect with airport passenger boarding bridges. Should ba

11、sic aircraft design requirements impose on a future model certain dimensional characteristics not complying with this document, note that: either alternative methods of embarking/disembarking passengers will need to be implemented, such as using the internal aircraft stairs, etc.; or upper deck pass

12、enger boarding bridges in the airports where such a new type of aircraft is to operate will require some degree of modification/reworking; or additional interface devices/equipment will be required in order to connect such a new type of aircraft with existing upper deck passenger boarding bridges. E

13、ach case results in increased aircraft-handling constraints and operating cost. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies.

14、For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7718-1, Aircraft Passenger doors interface requirements for connection of passenger boarding bridge Part 1: Main deck doors ISO 16004, Aircraft ground equipment Passenger boarding bridge or

15、transfer vehicle Interface requirements with aircraft doors 3 T erms a nd definiti ons No terms and definitions are listed in this document. INTERNATIONAL ST ANDARD ISO 7718-2:2016(E) ISO 2016 All rights reserved 1BS ISO 7718-2:2016ISO 7718-2:2016(E) ISO and IEC maintain terminological databases for

16、 use in standardization at the following addresses: IEC Electropedia: available at http:/ /www.electropedia.org/ ISO Online browsing platform: available at http:/ /www.iso.org/obp 4 Requirements 4.1 Minimum unobstructed space 4.1.1 Unobstructed space shall be provided for the connection of the passe

17、nger boarding bridge or passenger transfer vehicle as shown by the hatched area in Figure 1. The area bound by the dotted line represents the opening of the bridge or vehicle. 4.1.2 This area shall be kept completely clear of any external features such as aerials, drains, pitot heads, static ports,

18、sensors, incidence probes, aerodynamic strakes, access panels, etc. 4.1.3 Protrusions intended to divert rainwater away from the door opening are allowable in this area, provided they are not deemed part of the aircrafts structural or aerodynamic integrity and they do not interfere with the deployme

19、nt of the PBB canopy. 4.2 Minimum radius of the fuselage The cross-section radius of the fuselage in any part of the area defined in Figure 1 should not be less than 1,6 m (63 in). 4.3 Door sill height The passenger door sill height above the ground, at any part of its excursion range during normal

20、airport servicing/transit operations, should not exceed 8,4 m (330 in).2 ISO 2016 All rights reservedBS ISO 7718-2:2016ISO 7718-2:2016(E) Dimensions in millimetres (inches) 1 a e d Key 1 door sill height Dimension Maximum value Minimum value Note a 2 100 (82.7) Dimensions of the bridge opening b 2 8

21、50 (112.2) c 4 800 (189.0) d 300 (11.8) e 2 700 (106.3) On certain existing aircraft types with upward opening door, the bridge itself may need to be higher, though the specified interface area with the fuselage remains. Figure 1 Unobstructed space to be provided in the vicinity of upper deck passen

22、ger doors 4.4 Main deck bridge compatibility Where a passenger boarding bridge is intended to serve both upper and main deck doors, the requirements of ISO 7718-1 and ISO 16004 shall be taken into account for its design in addition to those of this document. ISO 2016 All rights reserved 3BS ISO 7718

23、-2:2016ISO 7718-2:2016(E) ISO 2016 All rights reserved IC S 49.100 Price based on 3 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. Bri

24、tish Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.

25、The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the kno

26、wledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and inter

27、national standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Copyright in BSI publications All the content in BSI public

28、ations, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Save for the pr

29、ovisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent. Storing and using stan

30、dards Standards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy

31、 is accessed at any one time. A single paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create

32、 an additional copy. This includes scanning of the document. If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions). Reproducing extracts For permission to reproduce content

33、from BSI publications contact the BSI Copyright & Licensing team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 5

34、5,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and s

35、ubscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits

36、 of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further i

37、nformation, email . Revisions Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please

38、inform the Knowledge Centre. Useful Contacts Customer Services Tel: +44 345 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 345 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK BSI Back Cover.indd 1 27/01/2016 14:20