BS SP 115 to 117-1956 Specifications for hydraulic surface-check type lubricating nipples for aircraft《航空用液压表面止动型润滑脂嘴规范》.pdf

1、BRITISH STANDARD CONFIRMED APRIL 1998 BS SP 115 to 117:1956 Incorporating Amendment Nos. 1, 2, 3 and 4 Specifications for Hydraulic surface-check type lubricating nipples for aircraft UDC 621-729.7 : 629.13BSSP 115 to 117:1956 These British Standards, havingbeen approved by the AircraftIndustry Stan

2、dards Committee and endorsed by theChairman ofthe EngineeringDivisional Council, were published under theauthority of the General Council of the Institution on 29March 1956 BSI 04-2000 Committee Reference ACE/14 Draft for comment CV(ACE) 5063 ISBN 0 580 34447 9 A British Standard does not purport to

3、 include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover,

4、pagesi andii, pages1 to7 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date of issue Comments 3506 September 1959 52

5、51 May 1964 6390 April 1968 607 September 1970 Indicated by a sideline in the marginBSSP 115 to 117:1956 BSI 04-2000 i Contents Page 1 Scope 1 Section 1. General requirements 2 Construction and performance 1 3 Materials 1 4 Dimensions 1 5 Screw threads 1 6 Anti-corrosion treatment 1 7 Freedom from d

6、efects 1 8 Identification and marking 1 Section 2 9 Inspection and testing 2 10 Batch 2 11 Sampling before components are assembled 2 12 Component dimensions and finish 2 13 Heat treatments and tests on components 2 14 Sampling of complete nipples 3 15 Assembly of components 3 16 Tests 3 Figure 1 En

7、velope dimensions of nipple head 4 Figure 2 1 / 4in. UNF straight nipple 4 Figure 3 1 / 4in. UNF 45 angle nipple 5 Figure 4 1 / 4in. UNF 90 angle nipple 5 Figure 5 Minimum clearance around hydraulic nipple 6 Figure 6 Test block 7 Table 1 British Standard numbers 2 ii blankBSSP 115 to 117:1956 BSI 04

8、-2000 1 1 Scope These British Standards specify the requirements for hydraulic, surface-check type, lubricating nipples having body attachment screw threads 1 / 4in. 28, Unified Fine (UNF), Class 2A limits. Three types of nipple are specified: a) straight and in one piece, with attachment screw thre

9、ads on one end of the body and the nipple on the other (Figure 2); b) a body with attachment screw threads on one end and a nipple set in the other end at 45 to the axis of the attachment screw threads (Figure 3); c) a body with attachment screw threads at one end and a nipple set in the other end a

10、t 90 to the axis of the attachment screw threads (Figure 4). Section 1. General requirements 2 Construction and performance a) The nipples shall incorporate a check valve, located at the surface of the nipple inlet tip, which with its seat shall provide a seal against the ingress of dirt or other fo

11、reign matter, but shall admit lubricant and prevent its escape, as required byd) tof) below. b) Springs shall be of non-collapsing design and of such quality of wire as to withstand the tests specified in this British Standard. c) The external surface of the nipple to be in contact, after installati

12、on, with a gun nozzle or coupler, shall be hardened to a case depth of 0.003 in. 0.005 in. Other parts required by the manufacturers approved drawings to be hardened shall be hardened as specified on the drawings. d) The nipples shall satisfactorily admit lubricant at1 000 lb/sq. in. without appreci

13、able leakage when a hydraulic-type coupler of approved design is connected and inclined to an angle of not less than10 in any radial direction between the axis of the coupler and the axis of inlet tip of the nipple. e) The opening pressure of the check valve shall be between 140 lb/sq. in. and 500 l

14、b/sq. in. f) The nipple shall retain lubricant at a sustained pressure of 5 000 lb/sq. in. without a total leakage in excess of 2 cu.cm in one minute. 3 Materials The nipples shall be made from steel complying with approved specifications see Clause 9 a). The manufacturers drawings and/or the specif

15、ications shall specify the materials and heat treatments and tests required on them. 4 Dimensions The nipples shall conform to the envelope dimensions shown in Figure 1, Figure 2, Figure 3, and Figure 4, and to those shown in the approved drawings (see Section 2, Clause 10), which shall be provided

16、with adequate dimensions and limits. The minimum clearance required around the nipples when they are installed in position is shown in Figure 5. 5 Screw threads a) The nipples shall each embody an attachment screw thread of a form to permit the nipple to be screwed tightly into a boss tapped with a

17、1 / 4in. 28 UNF 2B screw thread complying with the latest issue of BS 1580, “Unified screw threads”. b) Details of attachment screw threads shall be shown on approved manufacturing drawings and shall comprise 1 / 4in. 28 UNF 2A screw thread, complying with the latest issue of BS 1580, having2 1 / 2t

18、hreads run-out (root taper). c) Any other screw threads used in the internal construction of the nipples shall be in accordance with the approved drawing. d) The screw threads, before and after plating, shall be required to pass gauges approved by the Inspecting Authority. 6 Anti-corrosion treatment

19、 The body, and nipples before assembly, shall be uniformly coated with cadmium, in accordance with the latest issue of Ministry of Supply aircraft process specification D.T.D.904. The protective treatment for other parts shall be in accordance with the approved drawings. 7 Freedom from defects a) Th

20、e nipples shall be free from harmful defects. b) The nipples may be rejected at any time for faults in, or revealed by, manufacture, although they have been made from material passed previously for chemical composition and mechanical properties. 8 Identification and marking a) The nipples shall be i

21、dentified as “Unified” by a pattern of contiguous circles, e.g. OOO, of 3 / 32in. diameter indented on one or more flats of the hexagon and parallel to the axis of the nipple. b) The nipples shall be identified for ordering purposes by the relevant British Standard number shown in Table 1. The speci

22、fication number shall not be marked on the part.BSSP 115 to 117:1956 2 BSI 04-2000 c) The nipples shall be made into parcels which shall have the appropriate British Standard number and the Unified symbol of contiguous circles clearly marked on the labels. Table 1 British Standard Numbers Section 2

23、9 Inspection and testing a) For inspection purposes the manufacturers Inspecting Authority shall be provided with approved manufacturing drawings 1)and manufacturers approved specifications 1) , if any. Any changes in the drawings and specifications shall similarly be notified on approved drawings a

24、nd specifications and the Inspecting Authority shall have the right to carry out a complete series of tests before accepting any nipples to the new drawings and/or specifications. b) The nipples shall comply with the inspection and testing requirements specified in this section. The inspections and

25、tests shall be carried out to the satisfaction of the Inspecting Authority at whose discretion any quantity of nipples may be required to be submitted to any or all of the inspections and tests specified. The manufacturer shall satisfy the Inspecting Authority that adequate control is maintained thr

26、oughout manufacture to ensure compliance with the approved drawings and specifications. c) For the purposes of this section of the standard the following definitions shall apply: i) Batch. The output of an effectively continuous production run of each nipple free from any changes such as might be ex

27、pected to result in an appreciable variation in the quality of the finished product. ii) Random sample. A sample taken in such a manner that every nipple in the batch has a substantially equal chance of selection and the sample is thus a representative cross-section of the whole batch. 10 Batch A ma

28、nufacturing batch and batch record chart (or card) shall be established to the satisfaction of the Inspecting Authority. The record chart (or card) shall show the serial numbers of certificates covering approval of all materials and anti-corrosion treatments, and the results of all other inspections

29、 and tests specified in this British Standard. 11 Sampling before components are assembled a) A random sample containing 100 components shall be taken from each batch of a 1 000 or more components of each type. These batches shall not exceed 10 000 components. b) A random sample containing 25 compon

30、ents shall be taken from each batch of less than 1 000 components of each type. c) A batch of components shall be deemed to complywith the requirements of Section 1, Clauses3, 4, 5, 6, and 7, and Section 2, Clauses12 and 13 of this British Standard if the sample is proved to comply and the other req

31、uirements of this British Standard have been complied with to the satisfaction of the Inspecting Authority. If a component in the sample does not comply, all similar components in the batch shall be inspected for freedom from faults similar to those found in the sample component. All components in t

32、he batch which contain faults similar to those in the sample component shall be removed from the batch and a record shall be made on the batch chart (or card) of the quantity of components removed from the batch. d) The component batch number shall be correlated with the batch chart (or card) of the

33、 nipples (seeClause 10). 12 Component dimensions and finish The components shall be inspected to verify that they conform to the approved drawings. 13 Heat treatments and tests on components a) A minimum quantity of one per cent of hardened parts shall be selected from each heat-treated batch of par

34、ts. They shall be tested as stipulated inb) andc) below. BS No. Type of nipple Nipple with parallel thread BS SP 115 1 / 4in. UNF straight nipple BS SP 116 1 / 4in. UNF 45 angle nipple BS SP 117 1 / 4in. UNF 90 angle nipple 1) For nipples used on aircraft subject to British Civil or Military airwort

35、hiness requirements, the drawings and specifications have to be approved by the Air Registration Board (through a design authority approved by the Board), or by the Ministry of Supply, as appropriate.BSSP 115 to 117:1956 BSI 04-2000 3 b) A diamond pyramid test shall be carried out in accordance with

36、 BS 427, “Tables of diamond pyramid hardness numbers”, on each part referred to in a). All tests shall be made by the same method and under the same conditions of loading. The minimum hardness number for the nipple surface, referred to in Clause 2 c), shall be620. The minimum hardness number for oth

37、er parts shall be specified on the manufacturers approved drawing. c) A minimum quantity of five parts shall be selected from the parts which comply with the tests stipulated in b). They shall be fractured and the case depth in those parts shall comply with the case depth specified in Clause 2 c). d

38、) If any part tested as required in b) and c) fails to comply with the tests specified the batch of parts represented by the parts tested shall be deemed not to comply with this British Standard. e) The results of the inspections and tests made as above shall be recorded and correlated with the manu

39、facturing batch number of the nipples (seeClause 10). The method of hardening, the uniformity of heat-treatments and inspections and testing shall be to the satisfaction of the Inspecting Authority. 14 Sampling of complete nipples a) A random sample containing 100 nipples shall be taken from each ba

40、tch of 1 000 or more nipples. These batches shall not exceed 10 000 nipples. b) A random sample containing 25 nipples shall be taken from each batch of less than 1 000 nipples. c) A batch of nipples shall be deemed to comply with the requirements of this British Standard if the sample is proved to c

41、omply with the requirements of Clauses 14 and 15 and the other requirements of this British Standard have been complied with to the satisfaction of the Inspecting Authority. If a nipple in the sample does not comply, all the nipples in the batch shall be inspected and/or tested for freedom from faul

42、ts similar to those in the sample nipple. All nipples in the batch which contain faults similar to those in the sample shall be removed from the batch and a record shall be made on the batch chart (orcard) (see Clause 10) of the quantity of nipples removed from the batch. 15 Assembly of components T

43、he assembly and dimensions of the components shall be inspected to verify that they conform to the approved drawings. 16 Tests a) One per cent of each batch of nipples shall be tested for compliance with the requirements of Clause 2 d) to f) using a lubricant complying with the Ministry of Supply ai

44、rcraft material specification D.T.D.825 (XG275) and, for the pressure test, a test block with a minimum capacity of 10 cu. cm. A suitable form of test block is shown in Figure 6. b) If a nipple in the sample does not satisfy the requirements of the tests stipulated in a), all the nipples in the batc

45、h shall be inspected and/or tested for freedom from similar faults. All nipples in the batch which contain faults similar to those in the sample shall be removed from the batch and a record shall be made on the batch chart (orcard) (see Clause 10) of the quantity of nipples removed from the batch.BS

46、SP 115 to 117:1956 4 BSI 04-2000 All dimensions are in inches Figure 1 Envelope dimensions of nipple head All dimensions are in inches Figure 2 1 / 4in. UNF straight nippleBSSP 115 to 117:1956 BSI 04-2000 5 All dimensions are in inches Figure 3 1 / 4in. UNF 45 angle nipple All dimensions are in inch

47、es Figure 4 1 / 4in. UNF 90 angle nippleBSSP 115 to 117:1956 6 BSI 04-2000 All dimensions are in inches Figure 5 Minimum clearance around hydraulic nippleBSSP 115 to 117:1956 BSI 04-2000 7 Figure 6 Test blockBS SP 115 to 117:1956 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitutio

48、n BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should mak

49、e sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the