A-A-59490-1999 TRUNK LOCKERS [Superseded DLA MIL-T-10798 L REINST NOTICE 2 DLA MIL-T-10798 L DLA MIL-T-10798 L CANC NOTICE 1 DLA MIL-T-10798 K DLA MIL-T-10798 J DLA MIL-T-10798 H (.pdf

1、A-A-59490 7038054 OOLL570 391 W ? Y INCH-POUND A-A-59490 August 19,1999 SUPERSEDING 2 March 1990 MIL-T-10798L COMMERCIAL ITEM DESCRIPTION TRUNK LOCKERS The General Services Administration has authorized the use of tliis commercial item description as a replacement for the one type of MIL-T- 10798 fo

2、r all Federal agencies. 1. SCOPE. This commercial item description (CID) covers two types of high impact plastic tru-ers with or without trays. The type I trunk lockers are used in transporting and storing personal individual items, and the type II trunk lockers for transporting organizational equip

3、ment from garrisons to the field. 2. CLASSIFICATION. The trunk lockers shall conform to the following types and classes. All dimensions are the maximum outside dimensions in inches. Type I - 24-114 long by 20-1/4 wide by 12-1/2 deep (high) and 19 lbs., Max. Wt. with a Type II - 36-1/4 long by 18-114

4、 wide by 20-114 deep (high) and 31 Ibs., Max. Wt. with a minimum interior volume of 3.0 CU. fi. minimum interior volume of 5.0 CU. fi. Class 1 - Green (olive drab) Class 2 - Commercial Color Selection 3. SALIENT CHARACTERISTICS 3.1 Description. The trunk locker shall be made of weather resistant hig

5、h impact durable plastic and constructed so as to keep water from entering the trunk locker. The lid shall open and close without binding, held in the open position by cover supports or other devices and shall not self- lock in the closed position. The trunk locker shall be totally functional under

6、the ambient temperatures of -40F to 140F. The trunk locker shall be designed to be padlocked, and have a minimum of two interlocking latches, and two molded handle grips. The latches shall be recessed from the outside edge of the body in the latched position. The handle grips shall be located one on

7、 each end, and shall be flush with the outside edge of the trunk locker. All hardware shall be constructed of non-corrosive materialsor coated to prevent corrosion. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document shoul

8、d be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP-FNS, 2800 South 20th Street, Philadelphia, PA 19145-5099. AMSC N/A FSC 8460 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59490 = 9018054 00115

9、71 228 1 A-A-59490 * 3.2 Internal trays. When specified (see 7. I), the trunk locker shall contain a separate internal nesting tray, or trays, two maximum, made of high impact plastic, and having a minimum depth of 1-1/2 inches for type I locker and 2-112 inches for the type II locker. The internal

10、tray(s) shall sit evenly in the trunk locker and shall not cause bulging, distortion of the sides, or prevent the lid from closing when seated in the trunk locker. 3.3 Color (“Government unique” requirement) (see 7.6). The color of the trunk locker (both exterior and interior surfaces) shall be eith

11、er Green (class 1 - Olive drab); or Commercial color (class 2) as specified (see 7.1 and 7.3). Trunk lockers of a specific lot shall not exhibit any variation in shade from the specific color selected and specified in the contract for that production lot. Class 2 trunk lockers shall not reflect a “G

12、ovemment unique” requirement for color. For class 2 trunk lockers, the color shall be selected from the manufacturers standard commercial colors and the selected color shall be cited in the contract or purchase order. When specified, the color of the internal trays shall match the color of the trunk

13、 locker. 3.4 Molded identification marking (LGovernment unique” requirement) (see 7.6). When specXed (see 7. i), the trunk lockers shall be furnished with identification information molded or embossed into the surface of the container body. The information required shall be as follows: “Manufacturer

14、s Name Date of Manufacture 3, 4. REGULATORY REOUIREMENTS 4.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and mainte

15、nance requirements, and promotes economically advantageous life cycle costs. 5. OUALITY ASSURANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description except for any “Government unique” requirement specified, and shall c

16、onform to the producers own drawings, specifications, standards and quality assurance practices. The Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract or purchase order.

17、5.2 End item tests 5.2.1 Dro test. A trunk locker containing 30 pounds of weight for the type I, and 50 pounds of closed position, the trunk locker shall be dropped two consecutive times, once each on opposite comers, then dropped a third time on the bottom side (at an ambient temperature of 65F to

18、75F) from a height of four feet onto a smooth wooden surface without cracking, denting, or the lid opening. weight -+k- or e type II shall be used for the drop test. With the lid closed and the latches in the 5.2.2 Rain test. The top surface of the trunk locker with the lid closed and the latches lo

19、cked shall be exposed to rainfall at a rate of 4 inches per hour for a period of 15 minutes. The presence of any water in the trunk locker shall constitute failure of the rain test. 5.3 Metric roducts. Products manufactured to metric dimensions will be considered on an tolerances specified using con

20、version tables contained in the latest revision of ASTM E 380 and equa l-e-hx- asis wit t ose manufactured using inch-pound units, provided they fall within the 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-59490 I 9038054 OOL1572 Lb4 I A-A-

21、59490 all other requirements of this CID are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has

22、 the option of accepting or rejecting the product. 5.4 Visual examination. Each trunk locker shall be examined for the defects listed below. 5.4.1 Defects. The trunk locker shall be free of holes, cracks, dents, malformation, or deep scratch- sharp edges, dirt, grease, and foreign matter shall be re

23、moved. Color shall be as specified; no part shall be significantly shaded or noticeably uneven in color. There shall be no significant spots or stains (outside). There shall be no defects affecting serviceability, durability, or appearance. The marking shall not be missing, incorrect, or illegible.

24、The measurements of the item shall be as specified. Items shall be packaged in accordance with the contract or purchase order. 5.5 Acceptance criteria. Acceptance criteria shall be as specified in the contract or purchase order. 6. PACKAGING 6.1 Preservation, packing, and marking. Preservation, pack

25、ing, and marking shall be as spe4fied in the contract or order (see 7.1). 7. NOTES 7.1 Ordering data. Acquisition documents must specify the following: a. b. d. e. f. C. Title, number, and date of this CID. Size and class required (see 2). If trays are required and quantity required (see 3.2). Color

26、 required (see 3.3). Type of identification marking required (see 3.4). Packaging requirements (see 6. I). 7.2 Commercial item certification. When this CID is used for procurement, the commercial item certification clause must appear in the solicitation. 7.3 Trunk locker colors. Past experience has

27、shown that trunk lockers in any of the following color numbers of FED-STD-595 were found to be acceptable: Class 2 - Green Color No. 24097 34094 34095 34096 34097 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-59490 E 9038054 OOLL573 OTO I A-

28、A-59490 7.4 Sources for documents 7.4.1 Source of Government documents. Copies of military and Federal documents are available from: Defense Automated Printing Service (DAPS) 700 Robbins Avenue Philadelphia, PA 19 1 1 1-5094 Bldg. 4D (DPM-DODSSP) 7.4.2 Source of non-Government documents ASTM Standar

29、ds E 380 - Use of the International System of Units (SI) (The Modernized Metric System) 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) (Applications for copies should be addressed to American Society For Testing and Materials, 7.5 Sources of su competition is not limited to these companie

30、s. Titan Cases Industries, Inc. 25 Estate Drive Scarborough Ontario Canada MIH2Z2 1 . Manufacturers whose products are known to meet the requirements of this CID + are isted below, but these manufacturers may not produce both types; however, 1-800-352-7956 Rubbermaid Commercial Products 2 166 Wiscon

31、sin Avenue Washington, DC 20007 1-800-888-4779 Hardigg Cases 147 No. Main Street P.O. Box 201 South Deerfield, MA O 1373 1-800-978-6437 a 7.6 “Government unique” requirements. Whenever a “Government unique” requirement is included in the title of a paragraph under “Salient characteristics”, it means

32、 that the requirement is something that is not normally offered to the commercial marketplace by the manufacturer(s) of the subject commodity. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MILITARY INTERESTS: Custodians Army - GL Navy - NU Review Activities Army - MU Navy - MC A-A-57470 7018054 0033574 T37 A- A- 5 94 9 O CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS PREPARING ACTIVITY: DLA - CT Project 8460-0094 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-