ACI 440.2R-2017 Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures (Incorporates Errata August 22 2017).pdf

1、Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete StructuresReported by ACI Committee 440ACI 440.2R-17First PrintingMay 2017ISBN: 978-1-945487-59-0Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structu

2、resCopyright by the American Concrete Institute, Farmington Hills, MI. All rights reserved. This material may not be reproduced or copied, in whole or part, in any printed, mechanical, electronic, film, or other distribution and storage media, without the written consent of ACI.The technical committ

3、ees responsible for ACI committee reports and standards strive to avoid ambiguities, omissions, and errors in these documents. In spite of these efforts, the users of ACI documents occasionally find information or requirements that may be subject to more than one interpretation or may be incomplete

4、or incorrect. Users who have suggestions for the improvement of ACI documents are requested to contact ACI via the errata website at http:/concrete.org/Publications/DocumentErrata.aspx. Proper use of this document includes periodically checking for errata for the most up-to-date revisions.ACI commit

5、tee documents are intended for the use of individuals who are competent to evaluate the significance and limitations of its content and recommendations and who will accept responsibility for the application of the material it contains. Individuals who use this publication in any way assume all risk

6、and accept total responsibility for the application and use of this information.All information in this publication is provided “as is” without warranty of any kind, either express or implied, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose o

7、r non-infringement.ACI and its members disclaim liability for damages of any kind, including any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits, which may result from the use of this publication.It is the responsibility of the use

8、r of this document to establish health and safety practices appropriate to the specific circumstances involved with its use. ACI does not make any representations with regard to health and safety issues and the use of this document. The user must determine the applicability of all regulatory limitat

9、ions before applying the document and must comply with all applicable laws and regulations, including but not limited to, United States Occupational Safety and Health Administration (OSHA) health and safety standards.Participation by governmental representatives in the work of the American Concrete

10、Institute and in the development of Institute standards does not constitute governmental endorsement of ACI or the standards that it develops.Order information: ACI documents are available in print, by download, on CD-ROM, through electronic subscription, or reprint and may be obtained by contacting

11、 ACI.Most ACI standards and committee reports are gathered together in the annually revised ACI Manual of Concrete Practice (MCP).American Concrete Institute38800 Country Club DriveFarmington Hills, MI 48331Phone: +1.248.848.3700Fax: +1.248.848.3701www.concrete.orgACI Committee Reports, Guides, and

12、Commentaries are intended for guidance in planning, designing, executing, and inspecting construction. This document is intended for the use of individuals who are competent to evaluate the significance and limitations of its content and recommendations and who will accept responsibility for the app

13、lication of the material it contains. The American Concrete Institute disclaims any and all responsibility for the stated principles. The Institute shall not be liable for any loss or damage arising therefrom.Reference to this document shall not be made in contract documents. If items found in this

14、document are desired by the Architect/Engineer to be a part of the contract documents, they shall be restated in mandatory language for incorporation by the Architect/Engineer.ACI 440.2R-17 supersedes ACI 440.2R-08 and was adopted and published May 2017.Copyright 2017, American Concrete InstituteAll

15、 rights reserved including rights of reproduction and use in any form or by any means, including the making of copies by any photo process, or by electronic or mechanical device, printed, written, or oral, or recording for sound or visual reproduction or for use in any knowledge or retrieval system

16、or device, unless permission in writing is obtained from the copyright proprietors.1ACI 440.2R-17Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete StructuresReported by ACI Committee 440Carol K. Shield, Chair William J. Gold, SecretaryTarek AlkhrdajiCh

17、arles E. BakisLawrence C. BankAbdeldjelil BelarbiBrahim BenmokraneLuke A. BisbyGregg J. BlaszakHakim BouadiTimothy E. BradberryVicki L. BrownJohn BuselRaafat El-HachaGarth J. FallisAmir Z. FamRussell GentryNabil F. GraceMark F. GreenZareh B. GregorianDoug D. GremelShawn P. GrossH. R. Trey Hamilton I

18、IIIssam E. HarikKent A. Harries*Mark P. HendersonRavindra KanitkarYail Jimmy KimMichael W. LeeMaria Lopez de MurphyIbrahim M. MahfouzAmir MirmiranJohn J. MyersAntonio NanniAyman M. OkeilCarlos E. OspinaRenato ParrettiMaria A. PolakMax L. PorterAndrea ProtaHayder A. RasheedSami H. RizkallaRajan SenRu

19、dolf SeracinoVenkatesh SeshappaPedro F. SilvaSamuel A. Steere, IIIJennifer E. TannerJay ThomasHoussam A. ToutanjiJ. Gustavo TumialanMilan VatovecDavid WhiteSarah E. Witt*Co-chairs of the subcommittee that prepared this document.Consulting MembersP. N. BalaguruCraig A. BallingerHarald G. F. Budelmann

20、C. J. BurgoyneRami M. ElhassanDavid M. GaleSrinivasa L. IyerKoichi KishitaniHoward S. KligerKyuichi MaruyamaAntoine E. NaamanHajime OkamuraMark A. PostmaFerdinand S. RostasyMohsen ShahawySurendra P. ShahYasuhisa SonobeMinoru SugitaLuc R. TaerweRalejs TepfersTaketo UomotoPaul ZiaFiber-reinforced poly

21、mer (FRP) systems for strengthening concrete structures are an alternative to traditional strengthening techniques such as steel plate bonding, section enlargement, and external post-tensioning. FRP strengthening systems use FRP composite materials as supplemental externally-bonded or near-surface-m

22、ounted reinforcement. FRP systems offer advantages over tradi-tional strengthening techniques: they are lightweight, relatively easy to install, and noncorroding. Due to the characteristics of FRP materials as well as the behavior of members strengthened with FRP, specific guidance on the use of the

23、se systems is needed. This guide offers general information on the history and use of FRP strengthening systems; a description of the material properties of FRP; and recommendations on the engineering, construction, and inspection of FRP systems used to strengthen concrete structures. This guide is

24、based on the knowledge gained from experimental research, analytical work, and field applications of FRP systems used to strengthen concrete structures.Keywords: aramid fibers; bridges; buildings; carbon fibers; corrosion; cracking; development length; earthquake resistance; fiber-reinforced poly-me

25、rs; structural design.American Concrete Institute Copyrighted Material www.concrete.org2 EXTERNALLY BONDED FRP SYSTEMS FOR STRENGTHENING CONCRETE STRUCTURES (ACI 440.2R-17)CONTENTSCHAPTER 1INTRODUCTION AND SCOPE, p. 31.1Introduction, p. 31.2Scope, p. 4CHAPTER 2NOTATION AND DEFINITIONS, p. 62.1Notati

26、on, p. 62.2Definitions, p. 9CHAPTER 3BACKGROUND INFORMATION, p. 103.1Historical development, p. 103.2Commercially available externally bonded FRP systems, p. 10CHAPTER 4CONSTITUENT MATERIALS AND PROPERTIES, p. 114.1Constituent materials, p. 114.2Physical properties, p. 124.3Mechanical properties, p.

27、 124.4Time-dependent behavior, p. 134.5Durability, p. 144.6FRP systems qualification, p. 14CHAPTER 5SHIPPING, STORAGE, AND HANDLING, p. 155.1Shipping, p. 155.2Storage, p. 155.3Handling, p. 15CHAPTER 6INSTALLATION, p. 156.1Contractor competency, p. 166.2Temperature, humidity, and moisture considerati

28、ons, p. 166.3Equipment, p. 166.4Substrate repair and surface preparation, p. 166.5Mixing of resins, p. 176.6Application of FRP systems, p. 176.7Alignment of FRP materials, p. 186.8Multiple plies and lap splices, p. 186.9Curing of resins, p. 186.10Temporary protection, p. 19CHAPTER 7INSPECTION, EVALU

29、ATION, AND ACCEPTANCE, p. 197.1Inspection, p. 197.2Evaluation and acceptance, p. 19CHAPTER 8MAINTENANCE AND REPAIR, p. 208.1General, p. 208.2Inspection and assessment, p. 208.3Repair of strengthening system, p. 218.4Repair of surface coating, p. 21CHAPTER 9GENERAL DESIGN CONSIDERATIONS, p. 219.1Desi

30、gn philosophy, p. 219.2Strengthening limits, p. 219.3Selection of FRP systems, p. 229.4Design material properties, p. 23CHAPTER 10FLEXURAL STRENGTHENING, p. 2410.1Nominal strength, p. 2410.2Reinforced concrete members, p. 2410.3Prestressed concrete members, p. 2910.4Moment redistribution, p. 31CHAPT

31、ER 11SHEAR STRENGTHENING, p. 3111.1General considerations, p. 3211.2Wrapping schemes, p. 3211.3Nominal shear strength, p. 32CHAPTER 12STRENGTHENING OF MEMBERS SUBJECTED TO AXIAL FORCE OR COMBINED AXIAL AND BENDING FORCES, p. 3412.1Pure axial compression, p. 3412.2Combined axial compression and bendi

32、ng, p. 3612.3Ductility enhancement, p. 3612.4Pure axial tension, p. 37CHAPTER 13SEISMIC STRENGTHENING, p. 3713.1Background, p. 3813.2FRP properties for seismic design, p. 3813.3Confinement with FRP, p. 3813.4Flexural strengthening, p. 4013.5Shear strengthening, p. 4113.6Beam-column joints, p. 4113.7

33、Strengthening reinforced concrete shear walls, p. 41CHAPTER 14FIBER-REINFORCED POLYMER REINFORCEMENT DETAILS, p. 4314.1Bond and delamination, p. 4314.2Detailing of laps and splices, p. 4414.3Bond of near-surface-mounted systems, p. 45CHAPTER 15DRAWINGS, SPECIFICATIONS, AND SUBMITTALS, p. 4615.1Engin

34、eering requirements, p. 4615.2Drawings and specifications, p. 4615.3Submittals, p. 46CHAPTER 16DESIGN EXAMPLES, p. 4716.1Calculation of FRP system tensile properties, p. 4716.3Flexural strengthening of an interior reinforced concrete beam with FRP laminates, p. 5016.4Flexural strengthening of an int

35、erior reinforced concrete beam with near-surface-mounted FRP bars, p. 5616.5Flexural strengthening of an interior prestressed concrete beam with FRP laminates, p. 6216.6Shear strengthening of an interior T-beam, p. 6816.7Shear strengthening of an exterior column, p. 7116.8Strengthening of a noncircu

36、lar concrete column for axial load increase, p. 7316.9Strengthening of a noncircular concrete column for increase in axial and bending forces, p. 76American Concrete Institute Copyrighted Material www.concrete.orgEXTERNALLY BONDED FRP SYSTEMS FOR STRENGTHENING CONCRETE STRUCTURES (ACI 440.2R-17) 316

37、.11Lap-splice clamping for seismic strengthening, p. 8616.12Seismic shear strengthening, p. 8816.13Flexural and shear seismic strengthening of shear walls, p. 91CHAPTER 17REFERENCES, p. 97Authored documents, p. 98APPENDIX AMATERIAL PROPERTIES OF CARBON, GLASS, AND ARAMID FIBERS, p. 105APPENDIX BSUMM

38、ARY OF STANDARD TEST METHODS, p. 107APPENDIX CAREAS OF FUTURE RESEARCH, p. 108APPENDIX DMETHODOLOGY FOR COMPUTATION OF SIMPLIFIED P-M INTERACTION DIAGRAM FOR NONCIRCULAR COLUMNS, p. 109CHAPTER 1INTRODUCTION AND SCOPE1.1IntroductionThe strengthening or retrofitting of existing concrete structures to

39、resist higher design loads, correct strength loss due to deterioration, correct design or construction deficien-cies, or increase ductility has historically been accomplished using conventional materials and construction techniques. Externally bonded steel plates, steel or concrete jackets, and exte

40、rnal post-tensioning are some of the many traditional techniques available.Composite materials made of fibers in a polymeric resin, also known as fiber-reinforced polymers (FRPs), have emerged as a viable option for repair and rehabilitation. For the purposes of this guide, an FRP system is defined

41、as the fibers and resins used to create the composite laminate, all applicable resins used to bond it to the concrete substrate, and all applied coatings used to protect the constituent mate-rials. Coatings used exclusively for aesthetic reasons are not considered part of an FRP system.FRP materials

42、 are lightweight, noncorroding, and exhibit high tensile strength. These materials are readily available in several forms, ranging from factory-produced pultruded lami-nates to dry fiber sheets that can be wrapped to conform to the geometry of a structure before adding the polymer resin. The relativ

43、ely thin profiles of cured FRP systems are often desir-able in applications where aesthetics or access is a concern. FRP systems can also be used in areas with limited access where traditional techniques would be difficult to implement.The basis for this document is the knowledge gained from a compr

44、ehensive review of experimental research, analytical work, and field applications of FRP strengthening systems. Areas where further research is needed are highlighted in this document and compiled in Appendix C.1.1.1 Use of FRP systemsThis document refers to commercially available FRP systems consis

45、ting of fibers and resins combined in a specific manner and installed by a specific method. These systems have been developed through material characterization and structural testing. Untested combinations of fibers and resins could result in an unexpected range of properties as well as potential ma

46、te-rial incompatibilities. Any FRP system considered for use should have sufficient test data to demonstrate adequate performance of the entire system in similar applications, including its method of installation. ACI 440.8 provides a specification for unidirectional carbon and glass FRP mate-rials

47、made using the wet layup process.The use of FRP systems developed through material characterization and structural testing, including well-documented proprietary systems, is recommended. The use of untested combinations of fibers and resins should be avoided. A comprehensive set of test standards an

48、d guides for FRP systems has been developed by several organiza-tions, including ASTM, ACI, ICRI, and ICC.1.1.2 SustainabilitySustainability of FRP materials may be evaluated considering environmental, economic, and social goals. These should be considered not only throughout the construction phase,

49、 but also through the service life of the structure in terms of maintenance and preservation, and for the end-of-life phase. This represents the basis for a life-cycle approach to sustainability (Menna et al. 2013). Life cycle assessment (LCA) takes into account the envi-ronmental impact of a product, starting with raw material extraction, followed by production, distribution, transporta-tion, installation, use, and end of life. LCA for FRP compos-ites depends on the product and marke