AECMA PREN 2851-1989 Aerospace Series Marking of Parts and Assemblies Indications on Drawings Edition 1《航空和航天系列制图的零件和组件指示衡量》.pdf

1、AECMA PREN2851 A7 m 1012311 000q2b3 8 m Approved by COMITE DE NORMALISATION of A.E.C.M.A. 1989-1 2-05 prEN 2851 A. E. C. M .A. STAN DARD NORME A.E.C.M.A. Edition 1 A.E.C.M.A. NORM December 1989 EDITE PAR LASSOCIATION EUROPEENNE DES CONSTRUCTEURS DE MATERIEL AEROSPATIAL 88, boulevard Malesherbes, 750

2、08 PARIS -TEL. 45-63-82-85 UDC : Key words : The equivalent versions in French and German languages can be supplied by B.N.A.E, 8, rue Moreau-Vauthier 921 00 BOULOGNE-BILLANCOURT - FRANCE ENGLISH VERSION Aerospace series Marking of parts and assemblies I indications on drawings Srie arospatiale Luft

3、- und Raumfahrt Marquage des pices et ensembles Indications sur dessins Kennzeichnung von Bauteilen und Baugruppen Angaben in Zeichnungen This Aerospace series standard has been drawn up under the responsibility of AECMA (Association Europenne des Constructeurs de Matriel Arospafial). It is publishe

4、d on yellow paper in three equivalent versions (English, French, German). It will be submitted as a draft European Standard to CEN (European Committee for Standardization) for final vote, Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AEC

5、MANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2451 89 2012312 00042b4 T W prEN 2851 Page 2 Brief history This draft European Standard has been prepared bythe European Association of Aerospace Manufacturers (AE C MA). After inquiries and votes carried

6、out in accordance with the rules of this Association, this draft has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. , Copyright Association Europeene des Constructeurs de Materiel Aerospati

7、al Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2851 89 1012312 000q2b5 L W prEN 2851 Page 3 1 Scope and field of application O. This standard defines the method of indicating on drawings, with the exception of e

8、ngine drawings, the instructions for the marking of parts and assemblies for aerospace applications. 2 Purpose of marking The marking shall allow the identification and traceability of parts and assemblies. 3 Indications on drawings 3.1 General Drawings shall indicate the location and composition of

9、 the marking and the marking process les) . 3.2 Marking symbol The marklng symbol shall be a circle devided into 4 quadrants as shown in figure 1, containing the code(s) of the selected process(es) (see subclause 3.5). . This symbol is connected to the location of the marking by a line ending in an

10、arrow or a dot (see subclause 3.3.2), The size of the symbol shall be compatible with micro-filming requirements as well as those of computer aided design. . 3.3 Location of marking 3.3.1 Choice of location The location shall be chosen such that the marking : - does not impair the manufacturing tder

11、ances or the required surface conditions, - does not jeopardize strength, - remains visible after installation, if possible. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without

12、 license from IHS-,-,- _ AECMA PREN2851 89 m 1012311 OOOLiZhh 3 m prEN 2851 Page 4 3.3.2 Identification 3.3.2.1 The line shall end in a dot or an arrow depending upon which view is used to indicate the surface (see figures 2 and 3). No precise location within an area on a surface Figure 2 Figure 3 3

13、.3.2.2 Location d.efined within an area on a surface The line shall end in a dot inside the zone defined by a fine chain-dotted line (see figure 4). This zone may be dimensioned Figure 4 3.3.2.3 Optional location The information concerning the composition of the marking (see subclause 3.4) and the m

14、arking process (es) (see subclause 3.5) shall be combined wi.th reference to this standard (see clause 4). 3.4 Composition of the marking The marktng mav include any of the elements listed in table I. The choice of elements shall be the responsibilfty of the design office but in accordance with the

15、specific project rules. The composition shall he established on the drawinps by entering codes above the horizontal part of the identification line (see figure 5). 1-2 * - -7- Figure 5 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMAN

16、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2851 89 9 10l12311 0004267 5 9 Code 1 2 3 prEN 2351 Page 5 Elements Part number of the part or assembly 1) with, possib1.y the modifj-cation number or issue status Manufacturers identification (name, logo, co

17、de! Serial number Table 1 4 5 6 Product ion bat ch numb er Material batch number Sub-contractors identification 7 8 Life code Material type !only for “as received“ parts) 9 10 11 - Category of the “as received part“ (casting, band and die forging) Identification of melt lof a casting! Customers stor

18、es code Inspection stamp 2) 2) Being always necessary, this element does not need a code. - 3) This information is not known by the Design Office at the time the drawings are issued, therefore it is not possible to al.ocate a code. Identification of non-conformance 3) 3.5 Marking process The marking

19、 processes are set out in table 1. The choice chal!_ be the responsibility of the Design Office but in accordance with the specific project rules. Requirements are indicated on the drawings as follows : 3.5.1 Only one process is permissibi.e The code corresponding to the chosen process (see figure 6

20、) shall be written in the lower quadrant of the symbol. Figure 6 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2852 87 W 2012321 00011268 7

21、 prEN 2851 Page 6 3.5.2 Codes corresponding to the chosen processes shall be written in the quadrants of the. symbol (see figure 7!, if necessarv, mu3.tiple symbo1.s shall be used (see figure 8). Choice of more than one process is permissible Figure 7 Figure 8 3.5.3 Process choice is unrestricted Th

22、e corresponding code shall be placed in the lower quadrant figure 9). f the symbc (see Figure 9 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA P

23、REN285L 89 W LOL23LL 0004269 O Table 2. O O Codes Processes A Adhesive label B Tag or marking on packing C Chemical engraving D Transfer (decal.) E Electrolytic engraving F Manual punch marking G Tool or machine engraving H - Fixed label J Sand blasting K Electric pencil I Control punch marking M Ho

24、t pressure P Paint I RI By casting or forging I S Silk screen print I T I Marking with indelible ink (by hand or stamp) t r7 Vibro-engrsve I I XI No process specified Y Laser c 4 Reference to this standard on drawings The following shall be written in the appripriate space, if provided, in the drawi

25、ng title block, or nearby : Or, if the 1ocati.m 3-s optional (see 3.3.2.3) : Marking EN 2851 a- The composition of the part marking Il - 2) and the marking process (VI are to he considered as an example. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-