AECMA PREN 4408-2-2002 Aerospace Series Technical Drawings Representation of Parts Made of Composite Materials Part 2 Laminated Parts Edition P 1《航空航天系列.技术制图 复合材料部件表示法.第2部分 薄片型零件》.pdf

1、AECMA STANDARD NORME AECMA AECMA NORM Edition approved for publication 28June2002 prEN 4408-2 Edition P 1 June 2002 Comments should be sent within six months after the date of publication to Gulledelle 94 Procedure and Process Domain AECMA-STAN 8-1200 BRUXELLES PUBLISHED BY THE EUROPEAN ASSOCIATION

2、OF AEROSPACE INDUSTRIES - STANDARDIZATION klQhosT.m Gulledelle 94 - 8-1200 Brussels -Tel. + 32 2 775 81 10 - Fax. + 32 2 775 811 1 - www.aecma-stan.org ENGLISH VERSION Aerospace series Technical drawings Representation of parts made of composite materials Part 2: Laminated parts Srie arospatiale Des

3、sins techniques Reprsentation des articles en matriaux composites Partie 2 : Articles draps Luft- und Raumfahrt Technische Zeichnungen Darstellung von Teilen aus Verbundwerkstoffen Teil 2: Schichtstoffteile Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS und

4、er license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 2 prEN 4408-2: 2002 Foreword This standard has been prepared by former AECMA-CN CO and was reviewed by the Domain Technical Coordinator of AECMA-STANS Process Domain. Contents 1 2 3 4 5 5.1 5

5、.2 5.3 5.4 5.4.1 5.4.2 5.4.3 5.4.4 Annex A Normative references Terms and definitions _I._. . , , , . . . . . . , . , , , . . , . . , , , . . . . . . . . . , , . . . . . , . . . . . . . . . . , . . , . , , , , , , . , . . . . . ., , . , . . , . . . . . . . . . . . . . . . . . . . ._,. . ,. . . . . .

6、 . . Recommended workplan . Page 3 3 3 3 3 3 3 4 6 6 7 9 10 13 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 3 prEN 4408-2: 2002 I Scope This st

7、andard specifies the rules for the representation of laminated parts as well as the information to be indicated in technical drawings. It applies to aerospace structures using laminated parts. It shall be used together with EN 4408-1. 2 Normative references This European Standard incorporates by dat

8、ed or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard

9、only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 4408-1 Aerospace series - Technical drawings - Representation of parts made of composite materials - Part 1 : General rules 1) 3 Terms and definitions For the p

10、urposes of this standard, the terms and definitions given in EN 4408-1 apply. 4 General rules The general rules for the representation of parts made of composite material are specified in standard EN 4408-1. 5 Specific rules The representation of laminated parts basically differs from the others par

11、ts by the detailed representation of the different layers which make up the part. 5.1 Content of definition The definition of a part includes: - the list of the elements which make up the part; - the notes and definition of the materials; - the definition of the laminate aeras; - the representation

12、and the lay-up diagram; - the direction key(s) for laminating. 5.2 Recommended workplan See table 1. 1) Published as AECMA Prestandard at the date of publication of this standard Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for

13、 ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 4 prEN 4408-2: 2002 2 Define direction keys Table 1 5.4.3 I Work order I Observations I Subclause I 4 I 1 I Show laminate representation I Fill in lay-up diagram I 5.4.4.2 and EN 4408-1 5.3 I 5.4.1 and 5.4.2 I J I Make

14、drawing of the definition I of the part This drawing can be done before or during laminate representation 1 3 I Define laminate aeras I I 5.4.3 _ EN 4408-1 5.3 Laminate representation This representation, specifying the details of the layers making up the part and their individual identification, ma

15、y be: - a detailed view; - a cross section; - a perspective; . - The part is represented in an unmachined state. For the representation of a section, see figure I. Each layer is represented by a continuous thick line which marks the middle line of the layer. The extremities of each layer are represe

16、nted by a point, while keeping the drawing readable. No point shall be at direction changes or at intersections. - To avoid any reprography or microfilming problem, the minimum distance between two consecutive lines shall not be less than 0,8 mm or twice the line width (refer to the values in the ta

17、ble). - A complete representation at a more representative scale shall be considered to improve the readability of the drawing, especially in aeras with sudden changes in profile or connection, , . . 1 126 I /-E r? a The laminate representation does not define the ply or layer dimensions. Figure 1 C

18、opyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 5 prEN 4408-2: 2002 For a detailed view, see figure 2. 90 f ! i I I I I I I I I I l I I I I I I I I

19、 l I I I I l I ! I Area AUA5 - Area ALIA5 Figure 2 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 6 prEN 4408-2: 2002 I -._- t SI8 5.4 5.4.1 Laye

20、r identification Layer are identified by a number. Identification of a section (see figures 3 and 4). Identification is achieved by 3-figure numbers increasing 5 by 5 and beginning at 1 01. This identification method allows to interpose a layer without modifying the other identifications. Generaly t

21、he identification is marked at the extremity of the ply by a fine line which is interrupted before the designated ply (see figure 3). Analysis of the content of the laminate representation t 101 /- Figure 3 If the identification cannot be placed at the extremity of the ply, it shall conform to figur

22、e 4. 1 o1 .-.-.o /- 0 Figure 4 NOTE laminate and be renumbered. The line in the lay-up diagram corresponding to the old number can be left blank. If a layer is modified (cutting, material, direction), its number can be deleted from the drawing of the For a detailed view, see figure 5. Figure 5 Copyr

23、ight Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 7 prEN 4408-2: 2002 5.4.2 5.4.2.1 Connection of plies The connection of plies shall be spefied in the d

24、efinition: Connection of plies and dimensions Example of a section (see table 21 Table 2 - IL REPRESENTATIONS 5 A2 NOTE A2 AI 1 A2 NOTE NOTE Overlapped area and/or with edge to edge cutting allowable L : Value to be defined by the designer I REPRESENTATIONS I I EDGETOEDGE MANDATORY - I- AI 1 A2 NOTE

25、 I I T ALLOWABLE NOTE Overlapped area and/or with edge to edge cutting allowable I I O BS E RVATIO NS A note shall speciQ the dimension “a“ of the overlapping (s) NOTE For each ply: + a = . mm I- The overlapping is represented and identified as a ply. The localisation of overlapped aeras andlor with

26、 allowable edge to edge cutting shall be indicated in the laminate areas by notes. OBSERVATIONS The localisation of overlapped aeras andlor with allowable edge to edge cutting shall be indicated in the laminate areas by notes. Copyright Association Europeene des Constructeurs de Materiel Aerospatial

27、 Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 8 prEN 4408-2: 2002 mm 5.4.2.2 Recommended dimensions - Overlapping dimensions less than or equal to 1 (see figure 6 and table 3) mm Figure 6 1 Table 3 5 7 Format A4, A3,

28、A2 mm 5 0,5 1 13 0,8 AI, AO, X mm 7 0,7 2 3 195 d 2 4 - Dimensions for edge to edge connection (see figure 7 and table 4) Motif width . NOTE Minimum values for width of lines and point diameter, , i ar given in table 4. Figure 7 Table 4 r Dimension I d I Width e I point 0 1 Motif width Format Copyri

29、ght Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 9 prEN 4408-2: 2002 5.4.3 Definition of laminate aeras The aeras are identified by a letter followed by

30、a number; for example : AI, A2, A3, . . . On a cross section, aeras dimensioning lines are dimension lines which finish at the extremity of each aera in the form of points (see figure 8). A4 NOTE 7 In aeras with varying thicknesses, a note has to be added (see figure 9). Figure 8 X = . mm I -N times

31、 x mm I NOTE STAIRLIKE ARRANGEMENT OF LAYER WITH X= . mm Figure 9 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 10 prEN 4408-2: 2002 DESIGNATION

32、S 5.4.4 Symbols See table 5. SYMBOLS + I FINE WEB a I I m WEB, FILAMENTARY ROVING FABRIC, WARP SIDE I I - FABRIC, WEFT SIDE -t- BALANCED FABRIC OR SIDE IRRELEVANT BALANCED MULTILAYER O INDICATES THAT DIRECTION IS IRRELEVANT m STRUCTURAL ADHESIVE REPRESENTS ALL UNDEFINED LAYERS O0 MOTIF a non-woven,

33、of fine thickness warp side: side directed towards the positive areas of the direction key NOTE All combinaisons can be considered. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted

34、without license from IHS-,-,-Page 11 prEN 4408-2: 2002 Line width 5.4.4.1 Dimensions of symbols See figure 10 and table 6. mm mm 035 0,7 t t I I X -1 t Figure 10 Table 6 - Recommended values Format L 5 7 H 3 5 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS

35、under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 12 prEN 4408-2: 2002 5.4.4.2 See figure 11. Example of a lay-up diagram Dimensions in millimetres Key Bidirectional polyimide carbonhesin fabric Bidirectional E glasslepoxy resin fabric Re

36、dux 322 adhesive O“ 3 Stairlike arrangement of plies with: NOTE This lay-up diagram corresponds to the cross section in figure 1. Figure II Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking pe

37、rmitted without license from IHS-,-,-Page 13 prEN 4408-2: 2002 Annex A (informative) Bibliography EN 4408-1 EN 4408-3 Aerospace series - Technical drawings - Representation of parts made of composite materials - Part I : General rules Aerospace series - Technical drawings - Representation of parts m

38、ade of composite materials - Part 3: Parts including core materials Aerospace series - Technical drawings - Representation of parts made of composite materials - Part 4: Items obtained by winding Aerospace series - Technical drawings - Representation of parts made of composite materials - Part 5: Se

39、ams EN 4408-4 EN 4408-5 EN 4408-6 Aerospace series - Technical drawings - Representation of parts made of composite materials - Part 6: Preforms Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-