AIR FORCE A-A-59824-2009 TEST SET SPRAY PATTERN《喷洒型测试装置》.pdf

1、AMSC N/A FSC 4920 INCH-POUND A-A-59824 23 Feb 2009 COMMERCIAL ITEM DESCRIPTION TEST SET, SPRAY PATTERN The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE 1.1 Scope. This commercial item description (CID) describes a Fuel

2、Spray Pattern Test Set which hereafter will be referred to as the test set. The test set is capable of measuring the spray pattern angle and check for external leakage of a fuel atomizer assembly applicable to the A/M32A gas turbine engines. This CID describes the minimum provisions for ISO 9001 cer

3、tified manufacturers that meet or exceed these requirements. 2. SALIENT CHARACTERISTICS 2.1 General. The equipment shall be capable of operation within the accuracies, limits, and specifications herein. Equipment covered by this CID shall be commercially available equipment and may be modified to th

4、e extent necessary to meet the following description. 2.2 Order of precedence. In the event of a conflict between the text of this CID and the references cited herein (except for associated detail specifications, specification sheets or MS standards) the text of this CID shall take precedence. Nothi

5、ng in this CID, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 2.3 Physical characteristics. Overall Dimensions: Height 24 to 52 Inches Length 24 to 56 Inches Width 16 to 28 Inches Weight Not to exceed 275 LBS Beneficial comments, recommendati

6、ons, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: WR-ALC 542 CSW/CBSSS, 295 Byron Street, Robins AFB, GA 31098-1611. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59824 2 2.4 Electric

7、al Characteristics. Test set shall operate at power requirements of 220 VAC; 60 cycles per second. 2.5 Fluid pressure gauges. The fluid pressure gauges shall have an accuracy of +/- .25% with a range of 0 to 400 psig. The gauges shall also be no less than four and a half (4 ) inches to no more than

8、six (6) inches in diameter. 2.6 Test Fluid Requirements. The test set shall be in accordance with the MIL-PRF-7024 test fluid specification with approximately eight (8) to ten (10) gallons. MIL-PRF-7024 test fluid shall be used in lieu of JP-8 during testing. 2.7 Safety. The test set shall be classi

9、fied for use in hazardous work areas. 2.8 Marking. Test sets supplied to this CID shall be affixed with the manufacturers standard commercial part number. 2.9 Illumination. A lighting fixture, which is switched on either with a separate switch or with the supply pump, shall have enough illumination

10、inside of the spray chamber to aide in the observation of the spray quality while not shining directly into the operators eyes. 2.10 Semi-circular protractor. A protractor, to indicate the angle of the spray pattern, shall be fixed inside the spray chamber. Increments shall not be less than one (1)

11、degree and not more than five (5) degrees. 2.11 Calibration. The test set shall have a calibration interval of at least 180 days. 2.11.1 Calibration procedure. The test set shall provide for readily accessible calibration adjustments and maintenance adjustments. The manufacturer shall provide a cali

12、bration procedure so that minor repairs and calibration can be performed at the field level. 2.12 Manuals. Each test set shall be delivered with each unit, which is to include operators maintenance, basic operation instructions, and calibration procedures that have been approved by WR-ALC. The manuf

13、acturer shall also provide a list of all available options, as well as ordering information. 3. REGULATORY REQUIREMENTS 3.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provide

14、d that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with 23.403 of the Federal Acquisition Regulati

15、on (FAR). However, used, rebuilt, or refurbished items shall not be provided. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59824 3 4. PRODUCT CONFORMANCE PROVISIONS. 4.1 Product conformance. The test set provided shall meet the salient charact

16、eristics of this CID, conform to the manufacturers own drawings, specifications, standards, and quality assurance practices, and is the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5. PACKAGING 5.1 Packaging. The pres

17、ervation, packaging, packing, labeling, and marking shall be as specified in the contract or order. 6. NOTES. 6.1 Source of documents. 6.1.1 Department of Defense and Federal documents may be obtained at http:/assist.daps.dla.mil or from the Document Automation and Production Service, Bldg 4D (DPM-D

18、ODSSP), 700 Robbins Avenue, Philadelphia PA 19111-5094. 6.1.2 The Code of Federal Regulations (CFR) may be obtained at http:/www.gpoaccess.gov/cfr/ or from the Superintendent of Documents, U.S. Government Printing Office, Washington DC 20402. 6.2 Submitted products. The test sets submitted for sampl

19、e testing shall be a representative of the commercial off the shelf product. All features, performance, and environmental protection of the product tested shall be provided under any resulting contract or order. 6.3 Ordering data. The contract or order should specify the following: CID title and doc

20、ument number, product conformance provisions, and packaging requirements. 6.4 Commercial products. At the time of this CID preparation and coordination, the manufacturer listed was known to have commercial products that would meet the requirements of this CID. All other manufacturers must meet the r

21、equirements of this CID and submit testing and certification as required. (NOTE: This information should not be considered as a list of only approved manufacturers or be used to restrict procurement to only the manufacturers shown below.) Company Location CAGE POC POC Phone Mfr. Model/Part No. Bauer

22、 Inc. http:/ 175 Century Dr. Bristol, CT 06010-7482 70882 Andrew Parfitt 1-860-583-9100 ext. 183 1019003 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59824 4 6.5 Key Words. External Leakage Fuel Atomizer Measure of Angle Custodian: Preparing a

23、ctivity: Air Force - 84 Air Force - 84 Reviewer: Agent: Air Force - 99 Air Force 99 Project 4920-2009-001 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-