AIR FORCE A-A-59941-2013 CAPACITANCE STANDARD FIXED.pdf

1、 Comments, suggestions, or questions on this document should be addressed to: WR-ALC/404 SCMS/GUEEA, Robins AFB GA 31098-1813. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.dla.,mil. AMSC N/A FS

2、C 6625 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND A-A-59941 12 December 2013 COMMERCIAL ITEM DESCRIPTION CAPACITANCE STANDARD, FIXED The General Services Administration has authorized the use of this Commercial Item Description for all federal agenci

3、es. 1. SCOPE. This Commercial Item Description (CID) provides accurate reference values for the calibration of test measurement and diagnostic equipment for the development, repair and maintenance of navigational aids, radio frequency communications equipment and other measurement equipment. This CI

4、D lists the minimum performance, design, functional, environmental, reliability requirements and quality assurance provisions for the capacitance standard. 2. CLASSIFICATION. The capacitance standard covered by this CID is commercially available equipment that has factory installed options and/or ma

5、y be modified to the extent necessary to meet the following description. The test set shall be Class 3, in accordance with MIL-PRF-28800. 3. SALIENT CHARACTERISTICS. 3.1 Item Description. This capacitance standard shall provide accurate reference values for the calibration of test measurement and di

6、agnostic equipment for the development, repair and maintenance of navigational aids, satellite and radio frequency communications equipment and other measurement equipment. This standard shall be contained in an enclosure to maintain a stable environment and avoid RFI/EMI interference. 3.2 Capacitan

7、ce Values. The capacitance standard shall have minimum and maximum values with tolerance of 2.0% levels as show on table 1 Capacitance Value and Variability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59941 2 Capacitor Values (Tolerance) 10

8、pF (+/-0.2 pF) 500 pF (+/-10 pF) 900 pF (+/-18 pF) 5000 pF (+/-100 pF) 9000 pF (+/-180 pF) Table 1 Capacitor Values and worst case tolerance variation 3.3 Capacitor Types. The capacitance standard shall have non-polarized class 1 capacitors with dielectric material constant value between 15 and 100

9、with a delta percentage change of less than 0.4% from -55C to 125C (-67F to 257F). 3.4 Effective Series Resistance (ESR). The capacitance shall exhibit a maximum ESR equal or less than the absolute value of 2 ohms in alternate current measurement mode from wiring harness connector to connector, (see

10、 figure 1). Figure 1 Effective Serial Resistance vs. Frequency 3.5 Direct Current Voltage Operation. The capacitance standard shall have low drop out voltage small signal fast recovery diodes connected in series with the capacitors. A terminal connector tapped, allowing for connectivity with or with

11、out the diode(s) in series as to allow for direct current and alternating current applications, shown in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59941 3 Figure 2 Equivalent Schematic Diagram 3.6 Working Voltage. The capacitors i

12、n the capacitance standard unit shall be devices rated at a voltage equal or greater than 75 volts in working direct current voltage, WVDC75V. 3.7 Insulation Resistance (IR). The capacitance standard discrete devices shall exhibit a typical characteristic resistance (RCH) to 6.3 Giga ohms or R x C 5

13、00 Ohms times, capacity in Farads after 120 seconds at working voltage (WVDC). 3.8 Temperature Coefficient of Capacitance (TCC). The capacitance standard independent discrete devices shall have a typical TCC variability of 60 ppm/C from 55 C to + 125 C (131F to 257F). 3.9 Thermal Stability. The capa

14、citance standard accuracy shall vary no more than 2.0% of its value within the temperature range of 20C to 30C (68F to 86F) after tests in MIL-PRF-28800, section 4.5.5.1.1 has been performed for class 3 equipment classification (Per table 11 on page 41). The capacitance standard stability shall be w

15、ithin the values shown in table 2 at rated temperatures. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59941 4 Table 2 Operating Temperatures Values. 3.10 Design and Construction. The capacitance standard shall be used in both bench top, flight

16、 line and rack mounted environments. The capacitance standard is a commercial off the shelf item subject to commercial products regulatory standards. The capacitance standard shall comply with all applicable MIL-PRF-28800F sections. The capacitance standard shall be designed and constructed in accor

17、dance with all applicable European Union (EU) requirements in order to have the “CE” marking affixed. 3.11 System Safety. The system shall comply with all sections of the Underwriters Laboratories (UL), IEC/ISO standard 61010A and 61010B for electrical safety. 3.12 Sound Levels. The capacitance stan

18、dard acoustic noise shall conform to sound level requirements on section 1 of ISO 7779 and sections 1 b) meet appropriate performance standards, or c) at a reasonable price. The prime contractor is responsible for ensuring that all subcontractors comply with this requirement. 5. PRODUCT CONFORMANCE

19、PROVISIONS. 5.1 Contractor Certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this commercial item description, and the product conforms to the producers engineering drawings, specifications, standards, and q

20、uality assurance practices. The government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

21、HS-,-,-A-A-59941 7 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES 7.1 Source of Documents. 7.1.1 Military Specifications, Standards and Handbooks referenced herein may be obtained at https:/assist.dla.,mil or available from the Standardizati

22、on Documents Order Desk, 700 Robbins Ave, Bldg. 4, Section D, Philadelphia, PA 19111-5094. 7.1.2 FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh PA 15250-7954. Electronic copies of the FAR may be obtained from https:/www.acquisition.gov/far/. 7.1.3 ANSI/ASME doc

23、uments may be obtained online at http:/www.asme.org/ or from the American Society of Mechanical Engineers, 345 East 47thStreet, New York, NY 10017. 7.1.4 ISO documents can be obtained online at http:/www.iso.org or from the International Organization for Standardization, ISO Central Secretariat, 1,

24、ch de la Voie-Creuse, CP 56-CH-1211 Geneva 20, Switzerland. 7.1.5 EIA/ECA documents can be obtained online at http:/www.eciaonline.org/default.aspx . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59941 8 7.2 Key Words. Antenna Cable Frequency S

25、ignal NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/ . Custodians: Preparing Activity: Air Force 84 Air Force 84 Reviewers: Agent: Air Force 99 Air Force 99 (Project 6625-2014-006) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-