AIR FORCE MIL-R-9939-1961 RIVETER BLIND PNEUMATIC 1 8 - 3 16 INCH DIAMETER RIVETS《1 8 - 3 16英尺面径铆钉的气动铆钉枪》.pdf

1、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-9939 (USAJ?) 3.2 Component parts. The riveter shall consist of the follow- ing major component parts: a. Handle assembly b. Cylinder assembly c. Nose assemblies 3.3 Materials. able for the intende

2、d purpose of driving blind rivets. material shall not contain seams, cracks, blow holes, and other defects which may adversely affect the appearance, strength, endurance, and performance of the component parts. The materials used in the riveter will be suit- The 3.4 Design and construction. The rive

3、ter shall be designed for continuous operation and shall be constructed so that parts will not work loose in service or show excessive wear. The riveter shall be designed to withstand the conditions associated with shipping, storage, and service. 3.4.1 Maintenance. The riveter shall be designed and

4、con- structed so that adjustments and repairs, including assembly and disassembly can be accomplished efficiently without the use of special tools. 3.4.2 Control smoothness. The riveter shall be designed so that the operator can maintain complete and precise control at all times. cient tolerance to

5、afford maximum ease and control of operation. The working parts shall be manufactured with suffi- 3.4.3 Configuration. The riveter shall have good balance and shall be of such configuration that the operator can perform the required work with one hand in an efficient manner in restricted and close q

6、uarters. at approximately right angles to the body of the riveter. The nose assembly shall be mounted 3.4.4 Stability. The riveter shall be capable of efficient operation in any position. 3.4.5 Pulling capacity. The riveter shall develop a minhum pull of 1000 pounds using a 90 psig air pressure sour

7、ce. 3.4.6 Power connection. The riveter shall have a 1/4 inch standard female pipe connection. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.4.7 Keight. The weight of the riveter, complete with nose assembly will not exceed 6% pounds. 3.4.8 Siz

8、e. The overall dimensions of the riveter and nose assembly shall not exceed the following: Height - 12 inches Width - e inches Length - 7% inches 3.4.9 Riveter action and operation. The riveter shall be p-neu- matically and trigger operated and produce an axial pulling force through the nose assembl

9、y. The gun shall autamatically complete one cycle of pulling (and shifting as required) with one actuation OE the trigger. 3.5 Selection of specifications and standards. Specifications and standards for necessary commodities and services not speci- fied herein shall be selected in accordance with co

10、mmercial stand- ards except as provided in 3.5.1 and 3.5.2. 3.5.1 -Cornmercial parts. Commercial parts having suitable prop- .erties may be used provided: a. They may be replaced by the standard parts (MS or AN) without alteration. b. The corresponding standard part numbers are referenced in the par

11、ts list and, if practical, on the contractors draw- ings and manuals. 3.5.2 Standard parts. With the exception specified in 3.5.1, I5 and AN Standard Parts shall be used where.they suit the pur- pose. number. 3.6 Performance. The gun shall be capable of continuous operation in temperatures ranging f

12、rom -20 to 120%. They shall be identified on the drawings by their part G - 3.6.1 Storage. The gun shall be capbl f withstanding prolong- ed storage in temperatures ranging from -80 F to 160%. 3.7 Interchangeability, Al1 parts having the same manufacturers part number shall be functionally and dimen

13、sionally interchange- able. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R- 9939(USAF) 3.8 Identification of product. Equipment assemblies and parts shall be marked for identification in accordance with Military Standard MU-STD-130. 3.9 Techni

14、cal dta. Complete design activity drawings, parts list, and overhaul and maintenance manuals shall be submitted when specified (see 6.2). 3.10 Carrying case. Ametal carrying case shall be provided with each gun. gun and accessories in place to prevent damage. Ai1 edges of the case shall be smooth to

15、 prevent injury while handling. Provisions will be made in the case to hold the , 3.11 Workmanship. shall be fabricated and finished in a workman like manner. Particular attention shall be given to freedom from blemishes, defects, burrs and sharp edges, accuracy of dimensions, marking of parts and a

16、ssemblies, throughness of welding and brazing, alignment of parts and tightness of assembly screws and bolts. The gun, including all parts and accessories, 3.12 Installation of fasteners. The riveter shall be capable of installing all serrated-stem blind rivets, 1/8 through 3/16 inch diameter, inclu

17、ding mechanical lock spindle blind rivets, when using the proper nose assembly, and when the rivet pin breakload is not in excess of 1000 pounds. 3.13 Endurance. The riveter shall be capable of satisfactorily pulling 6000 blind rivets. 3.14 Nose Assembly. Sufficient nose assemblies shall be fur- nis

18、hed with each riveter to pull the rivets specified in 3.12. Additional nose assemblies will be furnished when ordered (see 6.2). 4. QUALITY ASSURBNCE PROVISIONS 4.1 Inspection responsibility. The supplier is responsible , for the performance of all inspection requirements as specified herein. his ow

19、n or any other inspection facilities and services accept- able to the government, and tests shall be kept complete and available to the government as specified in the contract or order. the rght to perform any of the inspections set forth in the test where such inspections are deemed necessary to as

20、sure supplies and services conform to prescribed requirements. Except as otherwise specified, the supplier may utilize Inspection records of the examination The government reserves Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-q33) (USAF) 4.2

21、 Classification of tests. The inspection and testing of the guns shall he classified as follows: a. b. Acceptance teats- - - - - - - - - - - - - - -(see 4.5) Preproductiontesting- - - - - - - - - - - - (see 4.4) 4.3 Tests 4.3.1 Environmental tests. The gun shall be subjected-to the following tests i

22、n accordance with the specified procedures of MU-E -49 7 O. 4.3.1.1 Low temperature. The gun shall be subjected to low temperature in accordance with procedure I of MIL-E-4970. Mter the exposure period, the temperature of the gun shall be raised to -20 F and stabiized. the gun shall be cycled at lea

23、st 100 times. There shall be no evidence of detrimental effects as a result of this test. With the temperature maintained 4.3.1.2 High temperature. The gun shall be subjected to high temperature in accordance with procedure I of MIL-E-4970. the exposure period, the temperature shall be lowered to 12

24、0 F and stablized. With the temperature maintained, the gun shall be cycled at least 100 times. detrimental effects as a result of this test, Bfter There shall be-no evidence of 4.3.1.3 Endurance. The riveter shall satisfactorily pull 6000 blind rivets. all incidents of the test, such as adjustments

25、 made, servicing performed and any irregular functioning of the gun and correct- ive measures taken. Notes shall be placed on the log sheet of 4.3.1.4 Examination of product. .Kach riveter shall be inspected to determine compliance with the requirements of this specification with respect to workmans

26、hip, materials, finishes, dimensions, weight, and marking. 4.3.1.5 Accuracy. Each gun shall satisfactorily pull a complete range of mechanical lock spindle rivets, 1/8 inch thru 3/16 inch diameter, except rivets that the pin breakload exceeds 1000.pounds. Failure to install these rivets satisfactori

27、ly will be cause for re j ect ion. 4.3.1.6 Teardawn. The gun shall be completely disassembled after completion of al1 tests knd inspected,for excessive wear, warpxe, deterioration cracks, or failure of parts. . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

28、 IHS-,-,-. 4.3.1.7 Packaging. Inspection of the preservation, packaging, packing and marking for shipment and storage. packs and the inspection of the preservation, packaging, packing .and marking for shipment and storage shall be in accordance with the requirements specified therein. Sample items o

29、r 4.4 Preproduction testing 4.4.1 Preproduction test sample. The preproduction test sample shall consist of three riveters as specified in the specification, upon satisfactory completion of the preproduction tests, these test samples may be used to satisfy the contractors commitments. 4.4.2 Preprodu

30、ction tests. The preproduction tests shall consist of ail the tests described under 4.3. 4.5 Acceptance tests. ing tests as described under: Each gun shall be subjected to the follow- a. Examination of product- - - - - - - - - -(see 4.3.1.4) b. Accuracy tests.- - - - - - - - - - - - - -(see 4.3.1.5)

31、 5, PREPAMTION FOR DELIVERY 5.1 Preservation and packaging. Preservation and packaging shall be level A or C as specified in EIL-P-12829 (see 6.2). 5.2 Packing. MIL-P-12829 (see 6.2) 5.3 Marking. In addition to any special marking required by the contract or order, unit packages, intermediate packag

32、es, and shipping containers shall be marked in accordance with the requirements of MXL-STD-129. Packing shall be level A, B, or C as specified in 6. NOTES 6.1 Intended use. The riveter covered by this specification is intended for use in the installation of serrated stem blind rivets including mecha

33、nical lock spindle rivets, 1/8 through 3/16 diameter, except rivets that have a pin breakload in excees of 1000 pounds. 6.2 Ordering data. Procurement documents should specify the . following: I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a. Tit

34、le, number, and date of this specification, b. Whether dradngs, parts list, and overhaul and maintenance manuals are required (See 3.9). ce Size and quantity of nose assemblies required. (see 3.14). d. Preservation .and packaging. (see 5.1). pecif i e. Level of packing. (see 5.21. f. Marking. (see 5

35、.3). NoTClk when Government drawings, ations or other data are used for any purpose other than in connection with a definitely related Goverment procurement operation , the United States Government thereby incurs no responsibility nor any obligation whatsoever; and the fact that the Govern- ment may

36、 have forunnilated, furnished, or in any way supplied the said drawings, specifications, or other data is not to be regarded by implication or otherwise as in any manner licensing the holder or any other person or corporation, or conveying any rights or permission to manufacture, use, or sel1 any patented invention that may in any way be related thereto. JFC MOAMA Mom o 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-