AIR FORCE MIL-W-6873 C-1991 WELDING FLASH CARBON AND ALLOY STEEL《碳合金钢快闪记忆体的焊接》.pdf

1、INCH-POUNDMIL-W-6873C13 Mav 1991SUPERSEDINGMnFw-6s73B6 September 1968MILITARY SPECIFICATIONWELDING; PLASH, CARBON AND ALLOY STEELThis specification is approved for use by all Departmentsand Agencies of the Department of Defense.1. SCOPE1.1 e. This specification covers procedures for flash welding al

2、loy steels and steels ofmedium and low carbon content to be used in the as-welded or heat heated condition.2. APPLICABLE DOCUMENTS2.1.1 The following specifications and standards forma part ofthis document to the extent specified herein. Unless otherwise specified, the issues of thesedocuments are t

3、hose listed in the issue of Defense Index of Specifications and Standards(DODISS) and supplement thereto, cited in the solicitation.Beneficial comments (recommendations, additions, deletions ) and any pertinent datawhich may be of use in improving this document should be addressed to ASD/ENES,Wright

4、-Patterson AFB OH 45433-6503 by using the self-addressed StrmdardizstionDocument Improvement ProposaLAMSC N/A FSC 3432DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL

5、-W-6S73CSPECIFICAONMILITARYMIL-H-6875 - Heat Treatment of Steel Process forSTANDARDMILITARYMfL-STD-1949A - Inspection, Magnetic Particle(Unfeas othenvise indicated, copies of federal and military specifications, and standards areavailable from the Standardization Documents Order Desk Bldg 4D, 700 Ro

6、bbins Avenue,Philadelphia PA 19111-5094.)2.2 QkdWKm The following daument(s) form a part of this dccument to the extentspecified herein. Unfeas otherwise specified, the issues of the documents which are DoD adoptedare those listed in the issue of the DODISS cited in the solicitation. Unless otherwis

7、e specified,the issues of documents not listed in the DODISS are the issues of the documents cited in thesolicitation.AMERICAN SOCIETY FOR lzSTfNG AND MATERIALSASTM A370 - Mechanical Testing of Steel ProductsASTM E8 - Tension Testing of Metallic Materials(Application for copies should be addressed t

8、o American Scciety for Testing and Materials, 1916Race Street, Philadelphia PA 19103.)AMERICAN WELDING SOCIETYANSI/AWS A3.O Standard Welding Terms and Definitions(Application for copies should be addressed to American Welding Society, Inc., 550 N.W.LeJeune Road, P.O. Box 351040, Miami FL 33135.)(Non

9、govemrrrent standards and other publications arc normally available from the organizationsthat prepare or distribute the dccuments. Thcae documen?s afso may be available in or throughlibraries or other informational services.)2.3 recedence. In the event of a conflict between the text of this documen

10、t and thereferences cited herein, the text of this document tskcs precedence. Nothing in this document,however, supersedes applicable laws and regulations unless a specific exemption has beenobtained.2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M

11、U-W-6873C3. GENERAL IUZQUHU3hIENTS3.1 IQlkma. The flash welding equipment shall be capable of consistently producingwelds which meet the requirements of this specification.3.1.1 n shallnot relieve the contractor of the responsibility of ensuring that all products or supplies submittedto the Governme

12、nt for acceptance comply with all requirements of the conmact. %rnplinginspection, as part of manufacturing operations, is an acceptable practice to ascertainconformance to requirements, however, this doss not authorize submission of known defectivematerial, either indicated or actual, nor does it c

13、ommit the Government to accept defectivematerial.4.2 pSOdUC. Allspecimems required herein for checking production flash weldingshall be welded in accordance with the established schedule.I 4.3 Samfhg4.3.1 Destrucb“vesamcde. Each time a machine is set up for a production run according to aqualified w

14、elding procedure, the set up shall be checked by welding and testing three parts, orsimulated production parts, as specified in 4.4.4. Alternate nondestructive inspection proceduresI may be used provided that the suitability of the procedures has been established by destructivetests and approved by

15、the procuring agency of the Government.12Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-6873C.5FIGURE 6. Alternate configuration for friction grippedtensile coupon13Provided by IHSNot for ResaleNo reproduction or networking permitted without l

16、icense from IHS-,-,-MIL-W-6873C4.3.2 . Unless greater frequency of sampling is specified, production lotsof critical and structural parts shall be sampled for proof testing as specified in table II.TABLE IL ,L9Miz Flash, Carbon and Allov SteelNATUR1OtCHANG1 (I&ncify pragtati numkr a71rd prep.and rmw

17、rite. 4f pot4*. AK4cA ucrJ hrctr u nrti). .MASON tOR MCOMMENDATIONHPANNG ACflVITfNAMf b. lELEPHONE i%dudc A/rJ Ccdd(1) COmmwdd (2) AUTOVONAS D/ E)i ES (513) 255-6295 725-6?95ADouss rlllcrl.drZlp raw t? VW M NOT MC1fVI 4 REPLYWITHIN 6S DAYS. COUTAO:Otftnn Quality ad SUd.dzation OffxaWright-Patterson AFB OH L5L33-65035203lrfibufqfibe.Suk*!401.FalbChurch.VA 11041.3466Tdq)ho.w (701) 75S2344 AU70WN 209-2140Form 1426. on 89 ?r, ”#c”, ,9.:, ,“$ , 0.5,.31. ,. !,. ,Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-