ANSI ASTM F2275-2017 Standard Practice for Treestand Manufacturer Quality Assurance Program.pdf

1、Designation: F2275 17 An American National StandardStandard Practice forTreestand Manufacturer Quality Assurance Program1This standard is issued under the fixed designation F2275; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the

2、 year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice provides minimum requirements for aquality assurance program.1.2 This standard does not purport

3、 to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.3 This international standard w

4、as developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referen

5、ced Documents2.1 ASTM Standards:2F2120 Practice for Testing Treestand Load CapacityF2121 Practice for Treestand Labels (Withdrawn 2017)3F2122 Practice for Treestand Safety Devices (Withdrawn2017)3F2123 Practice for Treestand InstructionsF2124 Practice for Testing Treestand Ladder, Tripod Standand Cl

6、imbing Stick Load Capacity (Withdrawn 2017)3F2125 Test Method for Treestand Static Stability and Adher-enceF2126 Test Method for Treestand Static Load CapacityF2128 Test Method for Treestand Repetitive Loading Capa-bilityF2337 Test Method for Treestand Fall Arrest SystemF2531 Test Method for Load Ca

7、pacity of Treestand Seats3. Significance and Use3.1 The purpose of this practice is to provide the minimumrequirements necessary for the establishment of a writtenquality assurance program for treestands and elevated huntingequipment.4. Drawing Control Procedure4.1 A procedure shall be in effect so

8、that appropriatemanufacturing drawings, their engineering revisions, and re-lated documents are utilized for each project. These drawingsand documents must be retained as long as the product remainsin production or distribution and for a period of five (5) yearsafter distribution ends.5. Material Co

9、ntrol Procedures5.1 Aprocedure shall be in effect to ensure that all materials,processes and components, including raw materials, are inaccordance with the engineering specifications.5.1.1 This procedure shall provide purchasing personnelwith all the information required to order appropriate materia

10、l.5.1.2 A receiving procedure shall be in effect so thatincoming material is checked against purchasing specifica-tions.5.1.3 A procedure shall be in effect so that material in stockcan be properly identified for future use.5.1.4 Documentation on any material, process, or compo-nents certified shall

11、 be filed for reference.5.2 A procedure will be in effect to ensure that the finalassembly of each product has a permanent date code indicatingits date of manufacture.5.2.1 A date code shall be located on each final productassembly.5.2.2 The date code shall include as a minimum the last digitof the

12、year and a code for the month or the week. (Example: forMarch, 2009 “39” or “C9” or “93” or “9C”.) Any code thatis logical, consistent and able to be decoded by the manufac-turer is acceptable. Any product in production for ten years ormore with no changes will be required to add a third number soth

13、at the last two digits of the year are known.5.2.3 Date codes shall be made permanent.1This practice is under the jurisdiction of ASTM Committee F08 on SportsEquipment, Playing Surfaces, and Facilities and is the direct responsibility ofSubcommittee F08.18 on Treestands.Current edition approved Dec.

14、 1, 2017. Published January 2018. Originallyapproved in 2003. Last previous edition approved in 2014 as F2275 10 (2014).DOI: 10.1520/F2275-17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards vol

15、ume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international sta

16、ndard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.16. I

17、nspection6.1 A procedure shall be in effect so that appropriateinspections are made on manufactured parts and subassembliesto ensure conformance with engineering specifications.6.2 A procedure shall be in effect so that appropriateinspections are made on purchased components.6.3 A procedure shall be

18、 in effect so completed units areinspected prior to delivery.6.4 Nonconforming components shall be identified andevaluated for disposition as follows:6.4.1 Reworked components shall be re-inspected in accor-dance with 6.1, 6.2,or6.3 of this practice prior to use.6.4.2 A component not suitable for us

19、e shall be altered ordisposed of to avoid accidental use.6.4.3 In some cases, a component may be determined to be“acceptable as is” or “as modified” after further evaluation. Insuch cases, appropriate review acceptance and documentationshall be a requirement.7. Testing and Compliance7.1 A procedure

20、shall be in effect to insure that producttesting has been completed and that products comply with theminimum requirements of applicable ASTM standards.7.1.1 The latest revision of the following applicable testmethods shall be met: Test Methods F2125, F2126, F2128,F2337, and F2531.7.1.2 The latest re

21、vision of the following applicable prac-tices shall be met: Practices F2120, F2121, F2122, F2123, andF2124.7.2 Test results and applicable documents must be retainedas long as the product remains in production or distribution andfor a period of five (5) years after distribution ends.7.3 A procedure

22、shall be in place for products to maintaintheir compliance status until such a time that conditions shouldarise that would warrant re-submission. Such conditions wouldinclude, but are not limited to: structural changes in regards todesign, material components, manufacturer of products, orchanges tha

23、t would otherwise diminish or call into question thestructural integrity, safety, or intended use, or a combinationthereof, of the product. Changes to applicable test methodsstated in 7.1.1 or practices stated in 7.1.2, or both, may alsowarrant re-submission.8. Keywords8.1 climbing stick; compliance

24、; specifications; treestand;tripod treestandAPPENDIX(Nonmandatory Information)X1. CONFORMANCE CRITERIA FOR TREESTANDSX1.1 This standard is provided for use by manufacturers oftreestands and testing companies. Criteria has been developedfor certification of treestands and this standard is an integral

25、part of the certification. However, a treestand conforming tothis standard alone does not constitute certification, and thosemanufacturers desiring certification must meet all applicablestandards as a minimum requirement.ASTM International takes no position respecting the validity of any patent righ

26、ts asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any

27、time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments wil

28、l receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by AST

29、M International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 172