ANSI UL 213-2004 UL Standard for Safety Rubber Gasketed Fittings for Fire- Protection Service (Fourth Edition Reprint with Revisions Through and Including May 2 2018)《消防设备用加橡胶衬垫的管配.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 213 Rubber Gasketed Fittings for Fire- Protection ServiceUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT

2、 AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Rubber Gasketed Fittings for Fire-Protection Service, UL 213 Fourth Edition, Dated November 4, 2004 Summary of Topics This revision of UL 213 was issued to incorporate the following changes: Co

3、rrection of the Effective Date for the Requirements for Paragraphs 5.4, 5.5, 7.2, 17.1, 17.3, and 18.1 from August 3, 2015 to August 3, 2017. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. Changes in requirements

4、 are marked with a vertical line in the margin and are followed by an effective date note indicating the date of publication or the date on which the changed requirement becomes effective. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitte

5、d in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any

6、 purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative ha

7、s been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and a

8、gainst any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for

9、those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are pr

10、eceded by a SUPERSEDED REQUIREMENTS notice. The following table lists the future effective dates with the corresponding reference. APRIL 27, 2015 UL 213 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Future Effective Date Reference Augus

11、t 3, 2017 Paragraphs 5.4, 5.5, 7.2, 17.1, 17.3, and 18.1 APRIL 27, 2015 UL 213 tr2UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL NOVEMBER 4, 2004 (Title Page Reprinted: April 27, 2015) 1 UL 213 Standard for Rubber Gasketed Fittings for Fire

12、-Protection Service First Edition August, 1978 Second Edition April, 1993 Third Edition July, 2001 Fourth Edition November 4, 2004 This ANSI/UL Standard for Safety consists of the Fourth Edition including revisions through April 27, 2015. The most recent designation of ANSI/UL 213 as an American Nat

13、ional Standard (ANSI) occurred on August 1, 2013. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submit

14、ted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights reg

15、arding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 213-2013UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MAY 22, 2009 RUBBER GASKETED FITTINGS FOR FIRE-PROTECTIO

16、N SERVICE - UL 213 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .4 2 Components 4 3 Units of Measurement 4A 4 Undated References .4A 5 Glossary 4A CONSTRUCTION 6 General 4B PERFORMANCE 7

17、 General 4B 8 Metallic Materials .6 9 Elastomeric Parts Tests 6 10 Leakage Test 6 11 Hydrostatic Test .7 12 Bending Moment Tests .7 12.1 General 7 12.2 Couplings 8 12.3 Side outlets .9 13 Flexibility Test for Flexible Fittings 10 14 Low Temperature Test for Dry Pipe Systems .11 15 Sprinkler Outlet F

18、low Characteristics Test .11 16 Pipe Outlet Flow Characteristics Test .12 MARKINGS 17 General 13 INSTRUCTIONS 18 Installation and Design Instructions .14 NOVEMBER 4, 2004 RUBBER GASKETED FITTINGS FOR FIRE-PROTECTION SERVICE - UL 213 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR

19、 DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 This standard covers rubber gasketed ttings intended for assembling sections of pipe in re protection systems, for example, couplings to attach pipe sections end to end, and side outlets to attach pipe sections at right angles. 1.2 Th

20、e products covered by this standard are intended for use in re protection service as outlined by the following Standards of the National Fire Protection Association: a) Installation of Sprinkler Systems, ANSI/NFPA 13; b) Installation of Standpipe, Private Hydrant, and Hose Systems, ANSI/NFPA 14; c)

21、Water Spray Fixed Systems for Fire Protection, ANSI/NFPA 15; and d) Installation of Private Fire Service Mains and Their Appurtenances, ANSI/NFPA 24. 1.3 The joints formed with the use of ttings covered by this standard prevent separation under pressure. 2 Components 2.1 Except as indicated in 2.2,

22、a component of a product covered by this standard shall comply with the requirements for that component. 2.2 A component is not required to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application of the component in the product covered by this s

23、tandard, or b) Is superseded by a requirement in this standard. 2.3 A component shall be used in accordance with its rating established for the intended conditions of use. 2.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components are int

24、ended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. NOVEMBER 4, 2004 RUBBER GASKETED FITTINGS FOR FIRE-PROTECTION SERVICE - UL 213 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTIO

25、N OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3 Units of Measurement 3.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. 4 Undated References 4.1 Any undated reference to a code or standard appearing in the requirements of this

26、standard shall be interpreted as referring to the latest edition of that code or standard. 5 Glossary 5.1 For the purpose of this Standard the following denitions shall apply. 5.2 FITTING, RUBBER GASKETED A device used to join pipes, ttings, and valves and uses an elastomeric material to seal the jo

27、int. 5.3 FLEXIBLE FITTING A rubber gasketed tting, which allows axial displacement, rotation and at least 1 degree of angular movement of the pipe without damage to the pipe for nominal pipe diameters of smaller than 8 inches (203.2 mm) or which allows axial displacement, rotation and at least 0.5 d

28、egrees of angular movement of the pipe without damage to the pipe for nominal pipe diameters of 8 inches (203.2 mm) and larger. These ttings are intended for installations where protection of piping against damage in areas where subject to earthquakes as required in NFPA 13. 5.4 PROPRIETARY GROOVES

29、Dimensions of the grooved end of pipe, ttings or valves specied by the rubber gasketed tting manufacturer that differ by dimension or tolerance from Standard Groove Dimensions. These other proprietary grooves are intended for use with specic rubber gasketed ttings to join grooved end pipe, ttings or

30、 valves having dimensionally compatible proprietary grooves. Added 5.4 effective August 3, 2017 5.5 STANDARD GROOVES Dimensions of the pipe, tting, or valve end specied by the rubber gasketed tting manufacturer that complies with the dimensions of Fire protection Automatic sprinkler systems Part 12:

31、 Requirements and test methods for grooved-end components for steel pipe systems, ISO 6182-12, for cut, rolled and cast grooves, intended for use with a groove type rubber gasketed tting to join pipe, ttings, or valves, ttings, or valves. Added 5.5 effective August 3, 2017 APRIL 27, 2015 RUBBER GASK

32、ETED FITTINGS FOR FIRE-PROTECTION SERVICE - UL 213 4AUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONSTRUCTION 6 General 6.1 Rubber gasketed ttings covered by these requirements shall have a rated pressure of 175 psig (1.20 MPa) or higher

33、. 6.2 Rubber gasketed ttings are intended for use with pipe, valves, and/or ttings that have been prepared to the specications of the rubber gasketed tting manufacturer PERFORMANCE 7 General 7.1 Rubber gasketed ttings intended for installation on pipe without grooves (plain end) are to be tested wit

34、h the specic pipe type and/or pipe having the minimum wall thickness specied by the manufacturer. 7.2 Rubber gasketed ttings intended for use with cut or rolled groove pipe are to be tested with the specic pipe type and pipe having the minimum wall thickness and groove dimensions specied by the manu

35、facturer. Revised 7.2 effective August 3, 2017 7.3 Representative sample ttings are to be subjected to the tests described in these requirements. APRIL 27, 2015 RUBBER GASKETED FITTINGS FOR FIRE-PROTECTION SERVICE - UL 213 4BUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBU

36、TION WITHOUT PERMISSION FROM UL AUGUST 1, 2013 RUBBER GASKETED FITTINGS FOR FIRE-PROTECTION SERVICE - UL 213 5 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 8 Metallic Materials 8.1 Specimen bars of metals used shall be

37、 prepared from the same heat or run of metal used in the tting samples submitted for investigation and test. The specimen bars shall conform to the minimum physical property requirements of the latest edition of the applicable ASTM or equivalent specication. Samples of bolts shall be tested without

38、special machining. 9 Elastomeric Parts Tests 9.1 An elastomeric part used to provide a seal shall have the following properties when tested as specied in the Standard for Gaskets and Seals, UL 157: a) For silicone rubber (having poly-organo-siloxane as its constituent characteristic), a minimum tens

39、ile strength of 500 psi (3.4 MPa) and a minimum ultimate elongation of 100 percent. b) For natural rubber and synthetic rubber other than silicone rubber, a minimum tensile strength of 1500 psi (10.3 MPa) and minimum ultimate elongation of 150 percent; or a minimum tensile strength of 2200 psi (15.2

40、 MPa) and a minimum ultimate elongation of 100 percent. c) Those properties relating to maximum tensile set; minimum tensile strength and elongation after oven aging; and hardness after oven aging, all as specied in UL 157. The maximum service temperature used to determine the oven time and temperat

41、ure for oven aging is 60C (140F). 9.2 The Standard for Gaskets and Seals, UL 157, provides for the testing of either nished elastomeric parts or sheet or slab material. Sheet or slab material is to be tested when the elastomeric parts are O-rings having diameters of less than 1 inch (25.4 mm). The m

42、aterial tested is to be the same as that used in the product, regardless of whether nished elastomeric parts or sheet or slab material is tested. 10 Leakage Test 10.1 A rubber gasketed tting assembly with pipe shall withstand for 1 minute, without leakage, an internal hydrostatic pressure of two tim

43、es its rated pressure. No leakage of the tting shall occur as the pressure is increased to the test pressure. 10.2 Leakage tests are to be conducted on ttings assembled onto sections of pipe at least 15 inches (381 mm) in length. The pipe ends to be joined by the tting are to be prepared and assembl

44、ed as specied by the manufacturer. The pipe ends of the test assembly are to be closed to provide for the assembly to be pressurized. The pressure is to be increased to twice the rated pressure and held for 1 minute. AUGUST 1, 2013 RUBBER GASKETED FITTINGS FOR FIRE-PROTECTION SERVICE - UL 213 6UL CO

45、PYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 11 Hydrostatic Test 11.1 A rubber gasketed tting assembly with pipe shall be capable of withstanding, for 1 minute without rupture, a test pressure equal to a multiple of the rated working pressure

46、as shown in Table 11.1. Table 11.1 Hydrostatic test pressures Fitting size, inches a Multiple of rated working pressure Less than 8 5 8 and less than 12 4 Larger than 12 3 Based on nominal ASTM A 795 Schedule 40 steel pipe sizes 11.2 Hydrostatic tests are to be conducted on rubber gasketed tting and

47、 pipe assemblies in accordance with the methods of 10.2, and with the pressure specied in 11.1. 12 Bending Moment Tests 12.1 General 12.1.1 The tting and pipe joint assembly shall not leak or rupture when subjected to the specied bending moment as determined by 12.1.3. 12.1.2 The pipe ends to be joi

48、ned by the tting are to be prepared and assembled as specied by the manufacturer. The assembly is to be pressurized to rated pressure. 12.1.3 The required bending moment is calculated based on twice the weight of water lled pipe over twice the maximum distance between pipe supports specied in the St

49、andard for Installation of Sprinkler Systems, ANSI/NFPA 13. Table 12.1 contains bending moment requirements for Schedule 5, 10, 30 and 40 steel pipe. The required bending moment for tting sizes and pipe combinations not specied in Table 12.1 is to be calculated according to the following formula: where: M is the required bending moment (lbft); w is the running weight of water lled pipe (lb/ft); and L is two times l, maximum hanger spacing (ft). NOVEMBER 4