ARMY A-A-1733 A-1993 STENCILBOARD《焊膏板》.pdf

1、A-A-L33A W 9599974 0355542 T98 W METRJCI A-A- 173 3A October 14. 1993 SUPERSEDING May 13, 1982 A-A- 173 3 COMMERCIAL ITEM DESCRIPTION STENCILBOARD The General SeMces Administration has authorized the use of this commercial item description, for all federal agencies. Scope. This description covers oi

2、led stencilboard which is suitable for marking with stencil-inks and stencil-paints. Classification: The stencilboard covered by this Commercial Item Description shall be of the following types and sizes, as specified (See Section 6, Ordering Data). Types: I - Light weight 1. SALENT CHARACTERISTICS:

3、 II - Heavy weight 0 A. Oiled stencilboard shall be ink resistant and shall be suitable for use with brushes, spray guns, or rollers. B. This stencilboard shall give a clean cut on a stencil machine or stamp and shall resist fzzing when in use. Beneficial comments, recommendations, additions, deleti

4、ons, clarifications, etc. and any data which may improve this document should be sent to General Services Administration, Federal Supply Service, Engineering Branch, 26 Federal Plaza, New York, N.Y. 10278. Distribution Statement A: Approved for public release Distribution is unlimited F S C 9310 Pro

5、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-3733A 9977974 0355543 924 A-A- 1 73 3A C. The stencilboard shall conform to the requirements as found in Table 1 when tested in accordance with paragraph 4.C.(3). Table I Characteristic Basis weight (9

6、2.9 m2) (1000 fP) Bursting strength minimum Grain Thickness Curl - maximum Type I 21.32 - 27.22 kg (47 - 60 Ibs) 611.5 kPa (74 p.s.i.) long direction 0.254-0.305 m (0.0 10-0.0 12 in) 3.175 mm (1/8 in) Type II 31.75 - 41.73 kg (70 - 92 Ibs) 1135.5 kPa (150 p.s.i.) long direction 0.330-0.457 m (0.013-

7、0.018 in) 3.175 mm (U8 in) D. Stencilboard shall be available in the sizes as specified in the contract or order. Dimensional tolerances shall be 5 0.32 centimeter (1/8 inch) in length and width. e E. The machine direction of the cut stencilboard shall be parallel to the long dimension of the cut st

8、encilboard. F. WorkmanshiD: The stencilboard shall have a hard, smooth surface and shall be free from checks, blows, indentations, holes, tears, foreign matter and other defects which affect serviceability and appearance. 2. APPLICABLE DOCUMENTS AND DOCUMENT SOURCES: The following documents form a p

9、art of this Commercial Item Description to the extent specified herein. Unless otherwise indicated, the issue in effect on the date of invitation for bids or request for proposal shall apply: Federal Redations: Title 40, Code of Federal Regulations, Protection of Environment, Part 250, Guideline for

10、 Federal Procurement of Paper Products containing Recovered Materials. Copies of the U.S. Code of Federal Regulations may be purchased with a VISA, Master Card, or prepaid check through: 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-1733A 99

11、99974 0155544 8bO A-A- 1 73 3A Government Printing Office Washington, D.C. Phone: (202) 783-3238 When ordering, ask for: Title 40, Parts 190-250 Stock Number: 869-0 13-00- 146-0 Mil it arv Stand a rd s : MIL-STD-105, Sampling Procedures and Tables for Inspection by Attributes Copies of Military Spec

12、ifications and Standards required by contractors in connection with specific procurement functions should be obtained from Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 191 11-5094. Industrv Standards: TAPPI test methods are available fiom TAPPI, Technology

13、ParWAtlanta, P.O. Box 1051 13, Atlanta, Georgia 30348. 3. REGULATORY REQUIREMENT: The contractor shall certi that the product offered shall contain the minimum of 20 percent postconsumer recovered material in accordance with 40 CFR, Part 250. The Government reserves the right to require proof of suc

14、h conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions in the contract 0 4. OUALITY ASSURANCE: A. ResDonsibiliv for Inspection: Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all the

15、 inspection requirements of this CID. Except as otherwise specified, the supplier may utilize his own facilities or any commercial laboratory acceptable to the Government. The Government reserves the right to perform any of the inspections set forth in the Commercial Item Description, where such ins

16、pections are deemed necessary to assure that supplies and services conform to prescribed requirements (See Section 6, Ordering Data). B. Sampling: All sampling shall be in accordance with MIL-STD-105. (1) Sampling for Visual Inspection. A random sample of stencilboard shall be taken from each lot. T

17、he inspection level shall be I with an Acceptable Quality Level (AQL) of 2.5 percent defective. The sample unit shall be one sheet. (2) SamulinP for Dimensional Insuection. A random sample of stencilboard shall be taken fiom each lot. The inspection level shall be S-3 with an AQL of 4.0 percent defe

18、ctive. The sample unit shall be one sheet. 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-1733A W 9999974 0355545 ?T? 8 A- A- l 73 3 A (3) Samdine for Tests. For the curl test, a random sample of stencilboard shall be taken from each lot. The

19、 inspection level shall be S-1 with an AQL of 4.0 percent defective. The sample unit shall be one sheet. TAPPI tests shall be in accordance with TAPPI T 400 for the applicable TAPPI test methods. (4) Samuling for PreDaration for Delivery. For examination of the preparation for delivery. The sample u

20、nit shall be one shipping container fully prepared for delivery, selected at random. The inspection level shall be S-2 with an AQL of 4.0 percent defective. C. Inmections. (1) Visual Examination. Samples taken in accordance with paragraph 4.B. 1. shall be examined to veri that the superficial produc

21、t requirements are in compliance with Section 1. (2) Dimensional Examination. Samples taken in accordance with paragraph 4.B.2. shall be examined to veri that all dimensionally measurable product requirements are in compliance with Section 1. (3) Tests. Samples taken in accordance with paragraph 4.B

22、.3. shall be subjected to the following tests to demonstrate consistency in product functionality, durability, and performance expectations. (a) For basis weight use TAPPI test method T-410. (b) For bursting strength use TAPPI test method T-403 (c) For grain use TAPPI test method T-409. (d) For thic

23、kness use TAPPI test method T-411 (e) Curl test: Two specimens, 30.48 centimeters by 30.48 centimeters (12 inches by 12 inches), shall be placed on a clean, dry, flat surface; one specimen with the felt side up and the other with the wire side up. If the specimen shows an edge curl; measure, to the

24、nearest .40 millimeter (1164 inch), the perpendicular distance fiom the supporting surface to the down face of the specimen at the edge. (4) Examination for Preuaration for Delivery. Samples taken in accordance with paragraph 4.B.4. shall be examined to determine compliance with Section 5. 5. PACKAG

25、TNG AND PACKTNG PROVISIONS. Each stencilboard shall be packaged to prevent damage during multiple shipments, handling, and storage. Packaged stencilboard shall be packed in accordance with normal commercial practice. The packing container shall be closed to prevent accidental opening and shall be su

26、ch to insure camer acceptable and safe delivery to destination, complying with the rules and regulations applicable to the mode of transportation to be used. i 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-1733A 9999974 Ol15554b b33 A-A- 1 7

27、3 3A 6. ORDERING DATA: Purchasers should select the preferred options permitted herein, and include the s following information in procurement documents: (1) Title, number, and date of this Commercial Item Description. (2) Type. (3) Size. (4) Special packaging and packing, if different than provisions in Packaging and Packing. (5) AnyMarking. (6) Specif), only if Bar Code marking is not required. I MILITARY INTERESTS: Militam Coordination Activitv Amiy - GL PREPARING ACTIVITY: GSA-FSS 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-