ARMY A-A-52151 A-1996 BELT SEAT PASSENGER TYPE AUTOMOTIVE COMMERCIAL VEHICLES《商用汽车乘载型座椅皮带》.pdf

1、A-A-5215LA D 9999974 0171793 210 m INCH-POUND A-A-521 5 1A June 28.1996 SUPERSEDING 18 May 1990 A-A-52151 COMMERCIAL ITEM DESCRIPTION BELT, SEAT, PASSENGER TYPE, AUTOMOTIVE, COMMERCIAL VEHICLES The General Services Administration has authorized the use of this Commercial Item Description (CID) for a

2、ll federal agencies. 1. SCOPE. This CID covers requirements for automotive passenger type seat belts, hereinafter called “seat belts”. The seat belts are intended for use in automotive commercial vehicles. 2. CLASSIFICATION. Seat belts are of the following types and lengths: Type I - Bolt-on. Length

3、 1 - 78 inches (in.) Length 2 - 58 in. Type II - Quick disconnect. Length 3 - 76 in. Length 4 - 56 in. 3. SALIENT CHARACTERISTICS. 3.1 Materials. Materials shall be in accordance with the manufacturers material specifications for seat belts. The use of recovered material made in compliance with regu

4、latory requirements is acceptable providing that all requirements of this CID are met (see 4.1). Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other data which may improve this document should be sent by letter to: U.S. Army Tank-automotive and Armaments Co

5、mmand, ATTN: AMSTA-TR-EBLUE, Warren, MI 48397-5000. AMSC NIA FSC 2540 DD TATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-? 0.25 min (typical) A-A-521 5 1A - I 0 I I I A tl I +I II 3.

6、1.1 Dissimilar metals. Dissimilar metals shall not be used in extremely close contact or having direct contact with each other unless protected against galvanic corrosion. ri v tongue I J I I I + - 3.2 Design and construction. The seat belts shall be designed and constructed in accordance with figur

7、es 1 and 2. . I I Tr I / II 2.31 max, 1.69 min- - I L 6 min I II I J I 1 washer - “d I y- I II I I 3 f 0.5 )te 4) nur (see nc I AA52151-2 I 58 I NOTE: 1. Dimensions are in inches. 2. max = maximum, min =.minimum. 3. Bolt - size 7/16, grade 5,2 required. 4. Nut - size 7/16, self-locking, 2 required.

8、FIGURE 1. Type I - bolt -on seat belt configuration. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52L5LA 9999974 OL71995 O93 A-A-5215 1A hole for cotter pin or split rivet r 0.25 min I metal to metal buckle r CID part number “L” min -1 AA521

9、51-4 I 56 NOTE: Dimensions are in inches. FIGURE 2. Type II - quick disconnect seat belt configuration. 3.3 Jdentification and markings. Identification and markings shall be permanent and legible and shall include , as a minimum, the manufacturers identification code (CAGE), the contract number, and

10、 the part identification number (PIN) (see 7.1 and 7.3). 4. REGULATORY REQUIREMENTS. 4.1 Recovered material. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. QUALITY

11、ASSURANCE PROVISIONS. 5.1 Responsibility for inspection. The contractor is responsible for the performance of all inspections (examinations and tests). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52151A M 9999974 0171996 T2T M A-A-52151A 5.

12、2 Contractor certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this CID and that the product conforms to the producers own drawings, specifications, workmanship standards, and quality assurance practices. It

13、ems with known defects shall not be submitted for Government acceptance. The Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 6. PACKAGING. Preservation, packing, and m

14、arking shall be as specified in the contract or order (see 7.3). 7. NOTES. (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 7.1 Part Identification Number (PIN) . The PINS to be used for seat belts acquired to this CID are created as f

15、ollows (see 7.3): u 52151 -x Type: 1 - Type I bolt-on, L = 78 in. 2 - Type I bolt-on, L = 58 in. 3 - Type II quick disconnect, L = 76 in. 4 - Type II quick disconnect, L = 56 in. CID number. Designates a CID. 7.2 Ad dressesforobtainingcop ie s of referen c edd o CU mens t . 7.2.1 Government publicat

16、ions. The Code of Federal Regulations (CFR) may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. 7.3 Orde rin g data. Acquisition documents must specify the following: a. Title, number, and date of this CID. b. Issue of the DoDISS to be cited i

17、n the solicitation, and if required, the specified issue of individual documents referenced. c. PIN and quantity required. d. Packaging requirements. I 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52L5LA m 9999974 OLL997 966 m A-A-52151A 7.4

18、 Cross-reference data. Seat belts conforming to this CID are interchangeablehbstitutable with seat belts conforming to A-A-52151. MILITARY INTERESTS: Custodian: CIVIL AGENCY COORDINATING ACTIVITY: GSA-FSS Army - AT Preparing Activity: Army - AT Review Activity: DLA - CS (Project 2540-0436) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-