ARMY DOD-D-51524-1986 DYE DISPERSE BLUE 3 (METRIC)《分散蓝3染料(公制)》.pdf

1、DOD-D-51524 68 H 7777706 OL221L3 3 r- I DOD-D-51524 ( EA) 20 May 1986 MILITARY SPECIFICATION DYE, DISPERSE BLUE 3 (METRIC) This specification is agyroved for use within the Chemical Research, Development and Engineering Center, Department of the Army, aud is available for use by all Departments and

2、Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers Disperse Blue 3 dye, chemically known as 1-methy lamino-bethanolami noanthraquinone a 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and stan- dard

3、s form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIO

4、NS FEDERAL L-P-378 - Plastic Sheet and Strip, Thin Gauge, Polyolefin PPP-D-723 - Drums, Fiber : Beneficial comments (recommendations, additions, deletions) and any perti- : : nent data which may be of use in improving this document should be addressed: : to: Commander, U.S. Am Chemical Research, Dev

5、elopment and Engineering : : Center , ATTN: SMCCR-SPD-TS, Aberdeen Proving Ground, MD 21010-5423 by : using the self-addressed Standardization Document Improvement Proposal (DD : : Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 6820 DISTRIBUTION STATEMENT A. Approved for

6、 public release; distribution is unlimited. a 2 y THIS DOCUMENT CONTAINS 7 PAGES. Licensed by Information Handling ServicesDOD-D-51524 ( EA) a MILITARY MIL-D-3464 - Desiccants, Activated, Bagged, Packaging Use and Static Dehumidification STANDARDS FEDERAL Fed. S MILITARY , No. 313 - Material Safety

7、Data Sheets Preparation and the Submission of MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads Attributes (Copies of specifications and standards required by contractors in connection with specific acqui

8、sition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other publications. The following documents form a part of this speci- fication to the extent specified herein. issues of the documents which are DOD adopted shall be those listed in th

9、e issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of the documents not listed in the DODISS shall be the issue of non- government documents which is current on the date of the solicitation. Unless otherwise specified, the ASTM STANDARDS D 1895 - Apparent Den

10、sity, Bulk Factor, and Pourability of Plastic D 3951 - Commercial Packaging (DOD Adopted) E 11 - Wire-Cloth Sieves for Testing Purposes (DOD Adopted) Materials (DOD Adopted) (Application for copies should be addressed to ASTM, 1916 Race Street, Philadelphia, PA 19103. (Nongovernment standards and ot

11、her publications are normally available from the organizations which prepare or distribute the documents. These documents also my be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the

12、references cited herein (except for associated detail specification, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemptson has been obtained. 2 L

13、icensed by Information Handling ServicesDOD-D-51524 b 797770b 0122115 7 m WD-D-5 1524 ( EA) 3. REQUIREMENTS 3.1 Chedea and physical characteristics. Dye, Disperse Blue 3 shall con- fofm to the chemical and physical characteristics of table I when tested as specified therein . TABLE I. Chemical and p

14、hysical characteristics : Test Character i s t ic : Requirement : paragraph i : Purity, percent by weight, minimum : 96.0 : 4.2.4.1 : : Particle size, prcent by weight passing: : 4.2.4.2 : : No. 20 sieve, mTnimum : 99.9 : No. 325 sieve, maximum : 40.0 : Apparent density, grams per milliliter, minimu

15、m : 0.20 : 4.2.4.3 : : No. 50 sieve, minimum : 95.0 3.2 Material Safety Data Sheets. Material Safety Data Sheets for Dye, Disperse Blue 3 shall be prepared and submitted by the contractor as specified in Fed. Std. No. 313 (see 6.3). 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection.

16、Unless otherwise specified in the con- tract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor my use his own or any other facilities suitable for th

17、e performance of the inspection requirements speci- fied herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed

18、requirements . 4.1.1 Responsibility for compliance. All items must meet ail requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specific

19、ation shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all require- ments of the contract. Sampling in quality conformance does not authorize sub- mission of known efective material, either indicat

20、ed or actual, nor does it commit the Government to acceptance of defective niaterial. 3 Licensed by Information Handling ServicesDOD-D-51524 68 m 7777706 OL22LLb 7 m DOD-D-51524 (EA) 4.2 Quality conformance inspection. 4.2.1 Lotting, A lot shall consist of the Dye, Disperse-Blue 3 offered for accept

21、ance at one time which has been produced by one manufacturer, at one plant, from the same materials, and under essentially the same manufacturing conditions provided the operation is continuous. In the event the process is a batch operation (see 6.4), each batch shall constitute a lot. 4.2.2 Samplin

22、g. 4.2.2.1 For examination of packaging. Sampling shall be conducted in accor- dance with MIL-STD-105. 4.2.2.2 For test. Three representative specimens of approximately 200 grams (g) each shall be randomly removed from the lot or batch of dye offered for acceptance and shall be placed in separate cl

23、ean, dry containers labeled to identify the lot represented. 4.2.3 Inspection procedure. k.2.3.1 For examination of packaging. The sample unit shall be one filled and closed shipping container, ready for shipment. Sample containers shall be examined for the following defects using an AQL of 2.5 perc

24、ent defective: Contents per container not as specified Container not as specified Polyethylene liner or closure thereof not as specified (level B Container closure not as specified Container damaged or leaking Marking incorrect, missing, or illegible Desiccant not as specified or missing (level B on

25、ly) Unitization not as specified only 1 4.2.3.2 For test. Each sample specimen taken in 4.2.2.2 shall be tested as specified in 4.2.4. rejection of the lot represented. Failure of any test by any specimen shall be cause for c. 4.2.4 Tests. Tests shall be conducted as follows: 4.2.4.1 Purity. Use onl

26、y high purity grades of methanol and water suitable for liquid chromatography residue analysis. Prepare and measure the area of the chromatographic peaks of a standard Disperse Blue 3 dye solution (see 6.5) and a solution of the specimen as follows: Weigh to the nearest 0.1 milligram (mg) exactly 10

27、0.0 mg of the dye and transfer quantitatively to a.200-milli- liter (mL) volumetric flask. Dissolve the dye in a solvent consisting of 90 percent by volume of methanol and 10 percent by volume of water, mix thor- oughly, and dilute to 200 ml; with the solvent (this stock solution contains 0.5 4 a Li

28、censed by Information Handling ServicesDOD-D-5152q 68 m 9977706 0122117 O DOD-D-51524 (EA) mg of dye per milliliter). graph, inject 10 microliters of the solutions and using a suitable integrator, measure thearea under the Disperse Blue 3 peaks with the detector set at 292 nanometers. Retention time

29、s are approximately 10.1, 8.87, and 8.03 minutes; actual-reten- tion times will depend on the age of the column. relative retention times. (RRT) to 1.0, the first component RRT should be calculated to be 0.803, and the second component RRT should be calculated to be 0.880.) methanol/water (gO/lO) fl

30、owing at -0.4 mL per minute (20 megapascals) through a 2.5 by 70 millimeter (mm) guard column and a 4.6 by 250 mm analytical column, both containing “Partisil-10 ODs“ (used for reversed-phase chromatography) (see 6.6) . peak as follows: Using a suitable high pressure liquid chromato- (Disperse Blue

31、3 dye is a mixture of three isomeric compounds. A better measure-will be the Setting the third component relative retention time The mobile phase is Calculate the percent by weight concentration of each specimen isomeric AnC, Pn = Percent purity of component n = - *n where: n = 1 to 3 and An = Area

32、of specimen peak for component n, Bn = Area of standard peak for component n, and Cn = Percent by weight purity of standard component n. Report the percent purity as the average of four sets of data from repeat injec- tions. Sum the data for peaks 1, 2, and 3 for each injection to get percent dye pu

33、rity for that injection. 4.2.4.2 Particle size. Use sieves conforming to ASTM E 11. Nest No. 20, No. 50, and No. 325 sieves in order of decreasing mesh size (with the sieve of largest mesh on top) on a receiving pan. mtely 10 g of the specimen onto the top sieve and brush the materie with a camels-h

34、air brush until no more specimen passes through the sieve. sieve and weigh the material retained. other sieves. sieve. Weigh to the nearest 0.1 g approxi- Remove the Repeat this procedure with each of the Calculate the percent by weight material passing through each 4.2.4.3 Apparent density. Determi

35、ne the apparent density in accordance with ASTM D 1895, method A. 5. PACKAGING 5.1 Unit packing. Dye, Disperse Blue 3 shall be unit packed level B or com- mercial as specified (see 6.2). 5.1.1 Level B. Uniform quantities of no less than 65 and no mre than 130 kilogramsqTpercent of the marked net wei

36、ght of dye shall be packed in a fiber drumconforming to type III, grade A, class 2 of PPP-D-723. Each drum shall be provided with a close-fitting bag liner formed from polyethylene-of 5 Licensed by Information Handling ServicesDOD-D-51524 b M 99979Ob OL22LL 2 DOD-D-51524 (EA) 101.6 micrometers minim

37、um thickness conforming to type I, class 1, grade and finish optional of -P-378. Seams shall be completely heat sealed and shall meet the heat-seal strength requirements of L-P-378. closed by heat sealing, tying, or knotting. A minimum of eight units of desic- cant conforming to MIL-D-3464 shall be

38、placed on top of the closed liner. Drum closure shall be fully gasketed and shall form a tight seal between the rim and the top of the drum. The filled bag shall be 5.1.2 Commercial. Uniform quantities of no less than 65 and no mre than 130 kilograms + i/4 percent of the marked net weight of dye sha

39、ll be unit packed in accordance with ASTM D 3951. 5.2 Packing. Dye, unit packed as specified in 5.1, shall require no further protection for shipment other than unitization. 5.3 Unitization. Shipping containers shall be unitized in accordance with the applicable requirements of MIL-STD-147 except th

40、at the pallet shall be as specified in the contract (see 6.2) . 5.4 Marking. Marking for level B shipments shall be in accordance with MIL- STD-129. Marking for commercial shipments shall be in accordance with ASTM D 3951. ture. letters and background to show the net weight of contents. In addition,

41、 each container of material shall be marked in accorance with the requirements of public law and regulations. name of product; quantity; warning symbol; signal word designating degree of hazard; actions to be followed or avoided; instructions in case of contact or exposure and notes to physicians; i

42、nstructions in case of fire, spill, or leak; instruc- tions for handling and storage; and disposal instructions. All shipments shall be marked to show lot number and date of manufac- Each container shall be durably and legibly marked with contrasting The marking shall include as applicable: 6. NOTES

43、 6.1. Intended use. Dye, Disperse Blue 3 is intended for use in the mnufac- ture of colored signaling smoke mixtures. 6.2 Ordering data. Acquisition documents should specify the following: (a) Title, number, and date of this specification (b) Level of unit packing required (see 5.1) (c) Type of pall

44、et required (see 5.3) 6.3 Material Safety Data Sheets. Contracting officers will identify those activities requiring copies of completed Material Safety Data Sheets prepared in accordance with Fed. Std. No. 313. The pertinent mailing addresses for sub- mission of the data are listed in appendix B of

45、 Fed. Std. No. 313. 6.4 Batch. A batch is defined as that quantity of material which has been manufactured by some unit chemical process or subjected to some physical mixing operation intended to make the final product substantially uniform. 6 Licensed by Information Handling ServicesDOD-D-51524 68

46、m 777770b 0122119 9 m 6.5 Dye of known purity. Dye, Disperse Blue 3 of known purity for use in 4.2.4.1 may be obtained by authority of the Procuring Contracting Officer (PCO). verification of its purity by authority of the PCO from Commander, U.S. Army Armament, Munitions and Chemical Command, Produ

47、ct Assurance Directorate, Aberdeen Proving Ground , MD 21010-5423. Alternately, the contractor may prepare his own standard dye and obtain 6.6 Trademark. “Partisil“ is a trademark of Whatman Inc. “Partisil-10 ODs“ is available from Whatman Inc., Chemical Separation Division, 9 Bridewell Place, Clift

48、on, NJ 07014. 6.7 Significant places. For the purpose of determining conformance with this specification, an observed or calmlated value should be rounded off “to the nearest unit“ in the last right-hand place of figures used in expressing the limiting value, in accordance with the rounding-off method of ASTM E 29. 6.8 Colour Index. The Colour Index number of Dye, Disperse Blue 3 is C.I. 61505. Custodian : Arqy - EA Preparing activity: Army - EA Pro j ect No. 682O-AO92 *US, GOVERNMENT PRINTING OFFICE: 1986-605-036/44601 7 Licensed by Information Handling Services