ARMY MIL-C-36465 A-1989 COT FOLDING HOSPITAL ALUMINUM《医院可折叠铝轻便小床》.pdf

1、1. SCOPE . MIL-C-3bLI65A 65 9 777770b 0260853 7 9 1 INCH-POUND I MIL-C-36465A 25 June 1989 SUPERSEDING MIL-C-36465 15 January 1966 MILITARY SPECIFICATION COT, FOLDING, HOSPITAL Aluminum This specification is approved for use by all Departments and Agencies of the Department of Defense. 1.1 Scope. Th

2、is specification covers one type of lightweight, adjustable, compactly folding, aluminum cot with a canvas cover. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1. Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to

3、the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). IBeneficial Comments (recommendations, ad

4、ditions, deletions) and any I !pertinent data which may be of use in improving this document should1 Ibe addressed to: Defense Personnel Support Center, Directorate of I IMedical Materiel, DPSC-RST, 2800 South 20th Street, Philadelphia, PAI 119101, by using the self-addressed Standardization Documen

5、t Improve- Iment Proposal (DD Form 1426) appearing at the end of this document I lor by letter. I AMSC/NA FSC 6530 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. O THIS DOCUMENT CONTAINS /a PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted

6、 without license from IHS-,-,-SPECIFICATIONS Federal V-T-285 QQ-A-200/8 QQ-A-591 QQ-A-601 TT-E-527 TT-P-1757 ccc-D-950 CCC-T-191 PPP-B-601 PPP-B-621 PPP-B-636 Military MIL-C-496 MIL-W-530 MIL-C-36465A 65 77Ob 0260854 O W MIL-B-543 MIL-C-5541 MIL-C-7219 MIL-L-10547 MIL-T-43566 STANDARDS Federal FED-S

7、TD-151 FED-STD-595 F ED-STD- 7 5 1 Mi 1 it ary MIL-STD-105 MIL-STD-129 MIL-STD-794 MIL-C-36465A Thread, Polyester Aluminum Alloy 6061, Bar, Rod, Shapes, Tube Aluminum Alloy Die Castings Aluminum Alloy Sand Castings Enamel, Alkyd, Lusterless Primer Coating, Zinc Chromate, Low-Moisture- Dyeing and Aft

8、ertreating Processes for Cotton Textile Test Methods Boxes, Wood, Cleated-Plywood Boxes, Wood, Nailed and Lock-Corner Boxes, Shipping, Fiberboard and, Wire, Extruded Sensitivity Cloths Clips, End, Strap Webbing, Textile, Cotton, General Purpose, Buckles, Tongueless and Web Strap Chemical Conversion

9、Coatings on Aluminum and Aluminum Alloys Cloth, Duck, Nylon Liners, Case, and Sheet, Overwrap; Water-Vapor- proof or Waterproof, Flexible Tape, Textile, Cotton or Polyester, General Purpose, Natural, or in Colors Natural or in Colors Metals; Test Methods Colors Stitches, Seams and Stitchings Samplin

10、g Procedures and Tables for Inspection by Marking for Shipment and Storage Parts and Equipment, Procedures for Packaging of Attributes 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-364b5A 65 7777906 0260855 2 9 I 2.3 Order of precedence. In

11、 the event of a conflict between the text of this document and the references cited herein (except for related associated detail specifications, specification sheets, or MS standards), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regul

12、ations unless a specific exemption has been obtained. MIL-C-36465A 8 (Unless otherwise indicated copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2.1.2 O

13、ther Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWING Defense Personnel Support Cente

14、r (DPSC) I 2109 Cot, Folding, Aluminum (Copies of the drawing may be obtained from: The Defense Personnel Support Center, 2800 So. 20th Street, Philadelphia, PA, 19101, Attn: DPSC-RST). 2.2 .Non-Government publications. The following documents form a part of this document to the extent specified her

15、ein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2).

16、COLOR ASSOCIATION OF THE UNITED STATES, INC. United States Army Standard Color Card for the Offical Standardized Shades of Sewing Threads Association of the United States, Inc., 200 Madison Avenue, New York 16, N.Y.). (Application for copies should be addressed to the: Color (Non-Government standard

17、s and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 3. REQUIREMENTS 3 Provided by IHSNot for ResaleNo reproduction or networking permitted with

18、out license from IHS-,-,-MIL-C-3b4bSA b5 9777906 02b085b 4 c MIL-C-36465A 3.1 Materials. Except as otherwise indicated, materials shall conform to the applicable portions of the documents referenced herein. When materials to be used are not specifically designated, they shall be suitable for the pur

19、pose intended. 3.1.1 Nylon duck. Nylon duck shall conform to MIL-C-7219, 7.25 OZ., class 1, Type III, O.G. 106. 3.1.2 Webbinq. Webbing for the tie straps shall conform to type IIb, class 4 of MIL-W-530. Reinforcing webbing shall conform to type II (hard texture), class 4 of MIL-W-530. Webbing shall

20、be vat dyed olive drab No. 7. The webbing shall be made mildew resistant by evenly depositing, within the webbing, a maximum of 1.28 percent copper-8- quinolinolate in lieu of the maximum specified in MIL-W-530. 3.1.3 Polyester thread. Thread for all stitching shall conform to V- T-285, for type II,

21、 class 1, letter size FF. The thread shall be vat dyed olive drab shade S-1, conforming to the United States Army Standard Color Card. The finished thread shall show good colorfastness to laundering, chlorine bleaching, and weathering. 3.1.4 Metal components. 3.1.4.1 Endpieces, and leqs, and sidepie

22、ces. Aluminum tubing, both round and square, shall be aluminum alloy 6062-T6. As an alternate, endpieces and legs shall be aluminum ally tubing temper T6, conforming with QQ-A-200/8, 1-1/8 inches outside diameter and 0.065 inch wall. Side pieces shall be round cornered, square aluminum alloy tubing

23、temper T6, conforming with QQ-A-200/8, 1-1/8 inches square and 0.065 inch wall. 3.1.4.2 Hinqe assembly. Hinge Assembly shall be a heat treated aluminum alloy sand casting, alloy 356 T6 conforming to QQ-A-601, class 3, or as an alternate an aluminum alloy die casting conforming to QQ-A-591, class A 3

24、80. Assembly shall be with 3/16 inch by 1-5/16 inch roundhead, monel metal or corrosion-resisting steel, annealed, bright-finished rivets. 3.1.4.3 Leq ansle braces. Leg angle braces shall be spring steel wire, 1/4 inch diameter. 3.1.4.4 Rivets. Rivets shall be aluminum alloy 2017114. 3.1.4.5 Buckles

25、. Buckles shall conform to PiIl-B-543 for type II, style 4, class I, 5/8 inch. 3.1.4.6 End clips. End clips shall conform to MIL-C-496 for type I, 5/8 inch, brass. 4 / 7 - /- -y. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-U . MIL-C-36465A 65 777

26、7906 02b0857 b U a MIL-C-36465A 3.1.5 Bindinq. Edge binding shall be lightweight cotton tape conforming to type I, class 4 of MIL-T-43566. Tape shall be vat dyed olive drab no. 7. 3.2 Construction. Construction shall conform to the requirements specified herein and to drawing 2109. Each unit shall b

27、e completely assembled. 3.2.1 Stitches, seams, and stitchings. All seams and stitchings shall be straight and shall conform to FED-STD-751. Stitches shall be type 301, formed by machine, with 8 to 12 evenly spaced stitches per inch. The ends of each continuous row of stitches (including ends due to

28、thread breaks) shall be anchored by-backstitches for a length of not less than 1 inch, except where anchorage is provided by another seam or stitching. Thread tension shall be properly maintained so that the lock will be embedded in the center of the material sewed. 3.2.2 Construction Details. Const

29、ruction shall be in accordance with DPSC drawing 2109, and as hereinafter specified. The removable cover shall be made of one piece nylon duck as shown on the drawing. overall dimensions of the cot shall be 75-1/2 inches long, 27 inches wide, and 16-3/8 inches high in the Set-up flat position. The c

30、ot shall measure 39 inches by 27 inches by 4-1/2 inches when folded. The cot shall have two adjustable sections, one on each end, each measuring 18 inches long and adjustable from the horizontal to 45 degrees above the horizontal in steps of 15 degrees. Tolerances shall be as shown on the drawing. T

31、he end clips for the tie straps shall be firmly attached without cutting the webbing which shall be inserted full depth and be flat at the point of entry. Turnunders and seams shall be neatly made. No loose or raveled edges shall be exposed. All cutouts shall be reinforced by webbing as shown on the

32、 drawing except that the edge binding specified in 3.1.5 shall be an acceptable alternate. In addition the turn back on the sides of the cover shall be more than 3 inches, if necessary, in order to utilize excess mater ia1 . The e 3.3 Finish. 3.3.1 Deqreasinq. All surfaces shall be thoroughly cleane

33、d and chemically degreased prior to chemical treatment. 3.3.2 Aluminum parts. All aluminum parts shall be finished with a chemical film conforming to MIL-C-5541. 3.3.3 Primer. After degreasing and chemical treatment, a primer coat shall be applied to all metal parts except the hardware and leg angle

34、 braces. The primer shall be zinc-chromate conforming to TT-P-1757. The primer coat shall form a grounding bond and base-for the finishing e 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-3b465A 65 777770b 02b0858 8 W 1 MIL-C-36465A 3.3.4 En

35、amel. The primer coat shall be followed by one coat of lusterless olive drab enamel conformins to TT-E-527. The resultant finish shall be hard, smooth, and highiy resistant to abrasion, chipping, and cracking. The color of the final finish shall be lusterless olive drab conforming to color X34087 of

36、 FED-STD-595. 3.3.5 Buckles and end clips. Buckles and end clips shall have a black oxidized finish. 3.4 Identification marking. On the underside of the cover, approximately 4 inches from one end and centrally located, there shall be stenciled, using black waterproof ink or waterproof. stencil paint

37、, the name or registered trademark of the manufacturer, the contract or purchase order number, and the letters U.S. The size of printing shall be not less than 1/2 inch high. 3.5 Workmanship. Workmanship shall be first class throughout. Complete cots shall be free from defects which detract from the

38、ir appearance or may impair their serviceability. Stains on the nylon duck, for use in fabricating the end item, shall not be cause for rejection of the end item. Minor distortion of the tubing at the corner bends shall not be cause for rejection, provided the strength of the frame is not impaired a

39、nd the dimensional tolerances are not exceeded . 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified her

40、ein. Except as otherwise specified, in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the in

41、spections set forth in this specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification sha

42、ll become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with al

43、l requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accep

44、t defective material. 6 t I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-n NIL-C-3b965A 65 9 7779706 2b857pT M MIL-C-36465A 4.1.2 Inspection. Inspection, as used in this specification, is defined as both examination (such as visual or auditory inv

45、estigation without the use of special laboratory appliances or procedures) and testing (determination by technical means of physical and chemical properties) of the item. 4.1.3 Certificates of quality. When available, certificates of quality, supplied by the manufacturer of the component or material

46、, listing the specified test method and test results obtained, may be furnished in lieu of actual performance of such testing by.the contractor. 4.2 Samplinq. 4.2.1 For examination. Sampling for examination shall be con- ducted in accordance with MIL-STD-105, and table I. Table I. Samplinq for exami

47、nation. I AQL (defects perl IFor visual examination Inspection level hundred units) I I I Major defects I II 1.0 I i Total (major and minor I I combined) defects II 4.0 I I I For dimensional examination s-2 I 2.5 I I 4.2.2 For tests. Sampling for tests shall be conducted in accordance with MIL-STD-1

48、05, and table II. rhread :Weight- . :Breaking strength : :Nonfibrous material: :Air permeability : :Length per pound : :Breaking strength : :Color . :Elongation . :Ply : 3.1.3 7 . . . 4.4.1.3 . . . . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1

49、1 5- MIL-C-3b4b5A b5 799Ub 02bOBbO b ? MIL-C-36465A Table II. Sampling for tests. - Continued. IWebbing and Tape I I I I l I I I I I I I IEnd clips I I Buckles I I IEnamel :Weight :Breaking strength :Weave :Texture :Acidity :Water absorption :Size content. :Color :Colorfastness :Mildew inhibitor :content :Mildew resistance :Material :Finish : Ma ter ia1 :Finish :Flexibility . . . : 3.1.2 and : : 3.1.5 . . . . . . . . . . . . . . . .