ARMY MIL-C-44218-1986 CARRIER AND CANTEEN COLLAPSIBLE 5-QUART CAPACITY《5夸特容量可折叠水箱支架》.pdf

1、h* :r MIL-C-44218 84 m 7777706 0401448 5 m MIL-C-44218(GL) 28 January 1986 (See 6.6) MILITARY SPECIFICATION CARRIER AND CANTEEN/COLLAPSIBLE, 5-QUART CAPACITY This specification is approved for use by the Natick Research, Development and Engineering Center, Department of the Army, and is available fo

2、r use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This document covers the requirements for a collapsible carrier and canteen with a 5-quart capacity. 2. APPLICABLE DOCUMENTS 2.1 Government documents. Unless otherwise specified, the following documents of the is

3、sue in effect on date of invitation for bids or request for proposal, form a part of this document to the extent specified herein. SPECIFICATIONS FEDERAL PPP-B-636 - Boxes, Shipping, Fiberboard PPP-F-320 - Fiberboard; Gorrugated and Solid, Sheet Stock (Container Grade), and Cut Shapes MILITARY MIL-C

4、-44219 - Carrier, Canteen, Collapsible, 5-Quart Capacity MIL-C-44216 - Canteen, Water, Collapsible, 5-Quart Capacity I i Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research

5、, Development and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. c t AMSC N/A FSC 8465 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimi

6、ted. ,- - THIS DOCUMENT CONTAINS - 8 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44238 84 m 777770b 0403447 7 m STANDARDS MIL-C-44218 (GL) MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking

7、for Shipment and Storage MIL-STD-147 - Palletized Unit Loads Attributes (Copies of documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) 2.2 Other publications. Unless otherwise

8、 specified, the following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this document to the extent specified herein. . AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for cop

9、ies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Technical society and technical association documents are generally available for reference from libraries. They are also distributed among technical groups and using Federal agenci

10、es. ) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document shall take precedence. 3. REQUIREMENTS 3.1 Guide samples. Samples, when furnished, are solely for guidance and Variations from this document may info

11、rmation to the contractor (see 6.3). appear in the sample, in which case this document shall govern. 3.2 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.2 and 6.4). 3.3 Components. 3.3.1 Carrier, Canteen, Collapsible, 5-

12、Quart Capacity. The carrier shall conform to MIL-C-44219. 3.3.2 Canteen, Water, Collapsible, 5-Quart Capacity. The canteen shall conform to MIL-C-44216. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-44214 4 7777906 040L4.50 3 3.4 Assembly.

13、 The assembly of the canteen into the carrier shall be as specified herein. 3.4.1 Assembling of components. 3.4.1.1 Insertion of collapsible canteen into carrier. Unsnap snap fasteners and extend closure flap and inner flap away from body of carrier allowing side opening to remain open. widthwise in

14、 3-1/2 inch increments, superimposing each folded portion upon itself. neck resulting in a 1-1/2 inch roll. canteen, neck first, through the side opening into the carrier, then passing the collapsible canteen neck through the carrier into and thru the mouth opening. With the collapsible canteen neck

15、 fully drawn thru the mouth, the mouth pull-up cord shall be securely drawn, and then square knotted locking the Collapsible canteen neck in the carrier mouth. The collapsible canteen will then be unrolled and unfolded inside the carrier allowing it to be in a flat state without wrinkles, folds or r

16、olls. The inner flap shall then be reinserted, being placed between the collapsible canteen and carrier body containing the snap fastener eyelets. The flap closure shall then be closed and the snap fasteners secured in a closed position. engaging hook and pile tape components attached to flap and po

17、uch of pocket in a flat smooth position. Fold collapsible canteen twice Roll folded collapsible canteen in the lengthwise direction up to the Insert folded/rolled collapsible Close pocket flap by 3.4.1.2 Shipment preparation. Lay assembly flat on a suitable surface with With the carrier pouch, carri

18、er the front down (front side has small pocket). neck and closure straps fully extended in a flat position, place the tiedown cords and retainer loops upon the back side of the carrier pouch. Fold each side of the assembly inward widthwise so that the sides overlap the center of the assembly by one

19、inch. Refold the widthwise folded assembly twice in lengthwise flat folds of increments of approximately 3 inches. Pull neck of carrier down over the folded assembly (placing short closure strap under neck panel in a flat position). Adjust assembly (if necessary) to have it lay in a smooth flat posi

20、tion. Twist long closure strap 180 degrees from its normal position to allow the side having the velcro tape attached face the assembler, fold the strap toward the carrier inserting it between the carrying loop and fastener tape. Engage the pile portion of the fastener tape on the strap to the hook

21、position on the carrier securely not permitting any looseness in the long closure strap. contains the specified strainer, the chain assembled to the rivet of the cap, and nylon cord properly attached to the free end of chain and neck. shall then be securely screwed to the neck of the canteen. O The

22、cap shall be removed and spout checked to see that it The cap 3.5 WorkmanshiE. The finished carrier and canteen assembly shall conform to the quality and grade of product established by this document. occurrence of defects shall not exceed the applicable acceptable quality levels. The 3 Provided by

23、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44218 BLI m 7779706 0403451 5 m c MIL-C-44218( GL) 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless o-.erwise specified in the contract or purchase order, the contractor is responsibl

24、e for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Go

25、vernment. The Government reserves the right to perform any of the inspections set forth in the document where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items must meet all requirements of section

26、s 3 and 5. The inspection set forth in this document shall become a part of the contractors overall inspection system or quality program. absence of any inspection requirements in the document shall not relieve.the contractor of the responsibility of assuring that all products or supplies submitted

27、to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. The 4.2 First article inspectio

28、n, When a first article is required (see 6.21, it shall be examined for the defects specified in 4.3.3. The presence of any defect shall be cause for rejection of-the first article. 4.3 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in aicordan

29、ce with MIL-STD-105. 4.3.1 Component and material inspection. In accordance with 4.1, components and materials shall be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified or qualified in this document or applicable purchase document

30、. 4.3.2 In-process inspection. Inspection of sub-assemblies shall be made to ascertain that construction details which can not be examined in the finished product are in accordance with specified requirements. reserves the right to exclude from consideration for acceptance, any material or service f

31、or which in-process inspection has indicated nonconformance. The Government 4.3.3 End item examination. 4.3.3.1 Visual examination. The end item (one complete collapsible carrier and canteen) shall be examined for the defects listed below. The lot size shall be expressed in units of end items. item.

32、 defects per hundred units, shall be 4.0. The sample unit shall be one end The inspection level shall be S-4 and the AQL, expressed in terms of 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I I i I l I I l I l I I Examine 0 Defect Carrier and can

33、teen/. Not folded in the specified manner. Tiedown cord or retainer loop extending outward away from folded assembly. Mouth pull up cord not drawn tight or knotted. Long closure strap not twisted as specified. Long closure strap not secured as specified. Long closure strap loose. Short closure strap

34、 not placed as specified. Pocket flap not closed as specified. Canteen not fully extended within carrier, One or more snap fasteners not closed. Side closure flap not closed. Inner flap not positioned as specified; i.e. not collapsible assembly Assembly not folded flat and smooth. between snap faste

35、ner eyelet and canteen. 4.3.4 Packaging inspection. An examination shall be made to determine that the preservation, packing, and marking comply with the section 5 requirements. Defects shall be scored in accordance with the list below. The sample unit shall be one shipping container fully packaged.

36、 The lot size shall be the number of shipping containers in the inspection lot. The inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5. Examine Defect Marking (exterior and Omitted; incorrect; illegible; of improper size, interior) location, sequ

37、ence or method of application. Ma ter ia1 s Any component missing, damaged, or not as specified. Workmans h ip Content Inadequate application of components, such as: incomplete closure of container flaps, improper taping, loose strapping or inadequate stapling. Bulged or distorted container. Number

38、of carrier and canteen/collapsible assemblies per shipping container is more or less than re,quired. - i/ - l/ For this defect, one shipping container in the sample shall be examined. 4.3.5 Palletization examination. An examination shall be made to determine that the palletization complies with the

39、section 5 requirements. Defects shall be scored in accordance with the list below. The sample unit shall be one palletized unit load fully packaged. The lot size shall be the number of 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44218 (GL

40、) palletized unit loads in the inspection lot. The inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5. Examine Defect Finished dimensions Length, width, or height exceeds specified maximum requirements. Palletization Pallet pattern not as specifi

41、ed. Interlocking of loads not as specified. Load not bonded with required straps as specified. Weight Exceeds maximum load limits. Mark i ng Omitted; incorrect; illegible; of improper size, location, sequence, or method of application. 5. PACKAGING 5.1 Preservation. Preservation shall be level A or

42、Commercial as specified (see 6.2). 5.1.1 Level A. Each collapsible carrier and canteen, assembled as specified (see 3.4.1), shall be unit packed in a fiberboard box conforming to style RSC, grade W6c of PPP-B-636. Inside dimensions of each box shall approximate 7-1/4 inches in length, 4-1/2 inches i

43、n width and 2-1/4 inches in depth. bottom flaps of each box shall be securely closed with waterproof tape as specified in the appendix of PPP-B-636. Approximate dimensions are furnished as a guide only. The top and 5.1.2 Commercial. Each complete collapsible- carrier and canteen assembly shall be pr

44、eserved in accordance with ASTM D 3951. 5.2 Packing. Packing shall be level A, B or Commercial as specified (see 6.2). 5.2.1 Level A packing. Sixty carrier assemblies, preserved as specified in 5.1, shall be packed in a snug-fitting fiberboard shipping container conforming to style RSC, grade V2s of

45、 PPP-B-636. packed flat, five in length, two in width and six in depth within a shipping container. Inside dimensions of each shipping container shall approximate 23- 3/4 inches in length, 15 inches in width and 15 inches in depth. Approximate dimensions are furnished as a guide only. Each shipping

46、container shall be closed in accordance with method III, waterproofed in accordance with method V and reinforced as specified in the appendix of PPP-B-636, except that the inspection shall be in accordance with 4.3.4. Level A unit packs shall be 6 Provided by IHSNot for ResaleNo reproduction or netw

47、orking permitted without license from IHS-,-,- l I I I l I I l I l I I l 1 I l l I i I l I 1 I l l l MIL-C-44218(GL) 5.2.2 Level B packing. Sixty carrier assemblies, preserved as specified in 5.1, shall be packed in a snug-fitting fiberboard shipping container conforming to style RSC, type CF (varie

48、ty SW) or SF, class domestic, grade 275 of PPP-B-636. Level A unit packs shall be placed flat five in length, two in width and six in depth within a shipping container. Inside dimensions of each shipping container shall approximate 23-3/4 inches in length, 15 inches in width and 15 inches in depth.

49、Approximate dimensions are furnished as a guide only. Each shipping container shall be closed in accordance with method II as specified in the appendix of PPP-B-636, except that the inspection shall be in accordance with 4.3.4. 5.2.2.1 Weather-resistant fiberboard containers. When specified (see 6,2), the shipping container shall be a grade VC, V3s or V4s fiberboard box fabricated in accordance with PPP-B-636 and closed in accordance with method III as sp