ARMY MIL-C-44218-1986 CARRIER AND CANTEEN COLLAPSIBLE 5-QUART CAPACITY《5夸特容量可折叠水箱支架》.pdf
《ARMY MIL-C-44218-1986 CARRIER AND CANTEEN COLLAPSIBLE 5-QUART CAPACITY《5夸特容量可折叠水箱支架》.pdf》由会员分享,可在线阅读,更多相关《ARMY MIL-C-44218-1986 CARRIER AND CANTEEN COLLAPSIBLE 5-QUART CAPACITY《5夸特容量可折叠水箱支架》.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、h* :r MIL-C-44218 84 m 7777706 0401448 5 m MIL-C-44218(GL) 28 January 1986 (See 6.6) MILITARY SPECIFICATION CARRIER AND CANTEEN/COLLAPSIBLE, 5-QUART CAPACITY This specification is approved for use by the Natick Research, Development and Engineering Center, Department of the Army, and is available fo
2、r use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This document covers the requirements for a collapsible carrier and canteen with a 5-quart capacity. 2. APPLICABLE DOCUMENTS 2.1 Government documents. Unless otherwise specified, the following documents of the is
3、sue in effect on date of invitation for bids or request for proposal, form a part of this document to the extent specified herein. SPECIFICATIONS FEDERAL PPP-B-636 - Boxes, Shipping, Fiberboard PPP-F-320 - Fiberboard; Gorrugated and Solid, Sheet Stock (Container Grade), and Cut Shapes MILITARY MIL-C
4、-44219 - Carrier, Canteen, Collapsible, 5-Quart Capacity MIL-C-44216 - Canteen, Water, Collapsible, 5-Quart Capacity I i Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research
5、, Development and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. c t AMSC N/A FSC 8465 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimi
6、ted. ,- - THIS DOCUMENT CONTAINS - 8 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44238 84 m 777770b 0403447 7 m STANDARDS MIL-C-44218 (GL) MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking
7、for Shipment and Storage MIL-STD-147 - Palletized Unit Loads Attributes (Copies of documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) 2.2 Other publications. Unless otherwise
8、 specified, the following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this document to the extent specified herein. . AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for cop
9、ies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Technical society and technical association documents are generally available for reference from libraries. They are also distributed among technical groups and using Federal agenci
10、es. ) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document shall take precedence. 3. REQUIREMENTS 3.1 Guide samples. Samples, when furnished, are solely for guidance and Variations from this document may info
11、rmation to the contractor (see 6.3). appear in the sample, in which case this document shall govern. 3.2 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.2 and 6.4). 3.3 Components. 3.3.1 Carrier, Canteen, Collapsible, 5-
12、Quart Capacity. The carrier shall conform to MIL-C-44219. 3.3.2 Canteen, Water, Collapsible, 5-Quart Capacity. The canteen shall conform to MIL-C-44216. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-44214 4 7777906 040L4.50 3 3.4 Assembly.
13、 The assembly of the canteen into the carrier shall be as specified herein. 3.4.1 Assembling of components. 3.4.1.1 Insertion of collapsible canteen into carrier. Unsnap snap fasteners and extend closure flap and inner flap away from body of carrier allowing side opening to remain open. widthwise in
14、 3-1/2 inch increments, superimposing each folded portion upon itself. neck resulting in a 1-1/2 inch roll. canteen, neck first, through the side opening into the carrier, then passing the collapsible canteen neck through the carrier into and thru the mouth opening. With the collapsible canteen neck
15、 fully drawn thru the mouth, the mouth pull-up cord shall be securely drawn, and then square knotted locking the Collapsible canteen neck in the carrier mouth. The collapsible canteen will then be unrolled and unfolded inside the carrier allowing it to be in a flat state without wrinkles, folds or r
16、olls. The inner flap shall then be reinserted, being placed between the collapsible canteen and carrier body containing the snap fastener eyelets. The flap closure shall then be closed and the snap fasteners secured in a closed position. engaging hook and pile tape components attached to flap and po
17、uch of pocket in a flat smooth position. Fold collapsible canteen twice Roll folded collapsible canteen in the lengthwise direction up to the Insert folded/rolled collapsible Close pocket flap by 3.4.1.2 Shipment preparation. Lay assembly flat on a suitable surface with With the carrier pouch, carri
18、er the front down (front side has small pocket). neck and closure straps fully extended in a flat position, place the tiedown cords and retainer loops upon the back side of the carrier pouch. Fold each side of the assembly inward widthwise so that the sides overlap the center of the assembly by one
19、inch. Refold the widthwise folded assembly twice in lengthwise flat folds of increments of approximately 3 inches. Pull neck of carrier down over the folded assembly (placing short closure strap under neck panel in a flat position). Adjust assembly (if necessary) to have it lay in a smooth flat posi
20、tion. Twist long closure strap 180 degrees from its normal position to allow the side having the velcro tape attached face the assembler, fold the strap toward the carrier inserting it between the carrying loop and fastener tape. Engage the pile portion of the fastener tape on the strap to the hook
21、position on the carrier securely not permitting any looseness in the long closure strap. contains the specified strainer, the chain assembled to the rivet of the cap, and nylon cord properly attached to the free end of chain and neck. shall then be securely screwed to the neck of the canteen. O The
22、cap shall be removed and spout checked to see that it The cap 3.5 WorkmanshiE. The finished carrier and canteen assembly shall conform to the quality and grade of product established by this document. occurrence of defects shall not exceed the applicable acceptable quality levels. The 3 Provided by
23、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44218 BLI m 7779706 0403451 5 m c MIL-C-44218( GL) 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless o-.erwise specified in the contract or purchase order, the contractor is responsibl
24、e for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Go
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ARMYMILC442181986CARRIERANDCANTEENCOLLAPSIBLE5QUARTCAPACITY5 夸特 容量 可折叠 水箱 支架 PDF

链接地址:http://www.mydoc123.com/p-441422.html