ARMY MIL-C-70950-1990 CASE CARTRIDGE 105MM M148A1B1E1 (M148A2B1)《 M148A1B1E1(M148A2B1)型105MM炮弹药筒》.pdf

1、MIL-C-70750 13 7997706 0370307 T Beneficial comments (recommcndations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, U.S. Army Armament, Munitions, and Chetniai Command, Ath. AMSMGQA, Picatinny Arsenal, New Jemy 07806-5

2、000 by using the self-addressed Standardization Document Improvement Propusai (DD Form 1426) appearing at the end of this document or by letter. MIL-C-70950 (AR) 12 January 1990 MILITARY SPECIFICATION CASE, CARTRIDGE, 105MM, M148AlBlEl This Specification is approved for use within the U. S. Army Arm

3、ament, Munitions and Chemical Comrnanql., and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification contains requirements, quality assurance provisions, and packaging for the IOSmm, M148AlBlEl Spiral-Wrapped Cartridge Case (SWCC) .

4、2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards and handbooks. The following specifications, standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue

5、of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitat-ion. SPECIFICATIONS MILITARY MIL-C-46487 - Cleaning, Preparation and Organic Coating of Steel Cartridge Cases MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions, Ge

6、neral Specification for AMSC NIA FSC1315 STATEMENT A, Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-70750 33 a 7999706 0370330 b W MIL-C-70950 (AR) STANDARDS MILITARY MIL-STD-1169 - Pac

7、kaging, Packing and Marking for Shipment of Inert Ammuni tion Components (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from: Military Specifications and Standards, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 O

8、ther Government documents drawings and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS ARMY 7548235 - Cartons, Ammuniti

9、on, for Interplant Shipment of Steel Cartridge Cases, Empty 37mm to 120mm, Inclusive 8647040 - Gage, Chamber 11735736 - Case, Cartridge, 105mm, M148AlBlEl (Copies of specifications, standards, handbooks, drawings, publications and other Government documents required by contractors in connection with

10、 specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity. 1 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents

11、 which are DoD adopted shall be those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation. ASTM Methods - AMERICAN SOCIETY FOR TESTING AND MATERIALS ASTM BI

12、17 - Standard Method of Salt Spray (Fog) Testing ASTM E18 - Standard Methods of Test for Rockwell Hardness and Rockwell Superficial Hardness of Metallic Mat er i als (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 1910

13、3-1 137.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- . MIL-C-70950 13 W 9999906 0370311 W 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes p

14、recedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 0 3. REQUIREMENTS 3.1 General. The cartridge case shall comply with the requirements of the applicable drawings and referenced specifications. 3.2 Material. The sup

15、plier shall be responsible for selecting from the classification list contained in the raw material specifications, the surface and physical condition of the raw material i used in manufacture. 4 3.3 Mechanical properties. The mechanical properties specified p.* on drawings and referenced specificat

16、ions shall be uniform throughout each section. 3.4 Protective coating. Protective coating as specified on drawings and referenced specifications shall apply to all surfaces of the cartridge case regardless of contour configuration and shall be uniform and continuous. Scratches exposing base metal ar

17、e not permitted. 3.5 Assembly tightness. The case shall be assembled in such a manner that there is no relative rotation between the base, the cup, and the body when a torque of 75+5 - in.-lbs. is applied to the base. 3.6 Maximum profile and alignment. Maximum profile and alignment of the cartridge

18、case shall comply with chamber gage drawing 11735736. 3.7 Ballistics. The cartridge case shall comply with the requirements of 3.7.1 through 3.7.5 when subjected to ballistic testing in, accordance with 4.6.7 in the following phases: l I I i I l I I I I i. a. Excess pressure phase b. Cold temperatur

19、e phase c. Excess, excess pressure phase (for information only) . 3.7. I Obturation. The cartridge case shall effectively seal the gun breech against leakage of gases generated during firing. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-70

20、950 23 W 9979906 0370312 T MIL-C-70950 (AR) 3.7.2 Extraction. After firing, the cartridge case shall be extracted by the service extractors when the gun is operated in the normal manner. 3.7.3 Primer retention. The cartridge case shall retain its primer during firing and extraction. 3.7.4 Propellant

21、 gas leakage. The cartridge case shall effectively prevent the entry of propellant gas through or between case components into the gun chamber. 3.7.5 Cracks or splits. After firing, the cartridge case shall be free of cracks or splits through all body plies. 3.8 Workmanship. The requirements for wor

22、kmanship are as specified on drawings, referenced specifications and the following: 3.8.1 Metal defects. The cartridge case shall be free of cracks, blisters, laps, deep scratches, dents, embedded foreign matter, porosity, and other metal defects. 3.8.2 Burrs. No cartridge case shall have any burrs.

23、 3.8.3 Foreign matter. No cartridge case shall contain chips, dirt, grease, oil, rust, corrosion, or other foreign matter. 3.9 First article inspection. This specification contains technical provisions for first article inspection. Requirements for the submission of first article samples by the cont

24、ractor shall be as specified in the contract. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein

25、. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspec

26、tions set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirement s. 4 a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-70950 13 m 9779706 0370313 L - MIL-C-7095

27、0 (AR) 4.2 Responsibility for compliance. All items shall meet all 0 requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification s

28、hall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection as part of manufacturing operations, is an acceptable practice to ascertain conformance to requ

29、irements, however, this does not authorize submission of known defective materials, either indicated or actual, nor does it commit the Government to accept defective material. 4.3 Classification of inspections. The following types of P inspections shall be performed on this item: a. First article in

30、spection b. Quality Conformance Inspection P 4.4 First article inspection. 4.4.1 Submission. The contractor shall submit a first article sample as designated by the Contracting Officer for evaluation in accordance with provisions of this specification. The sample shall be manufactured using the same

31、 materials, equipment, processes, and procedures as will be used in regular production. All parts and materials, including packaging shall be obtained from the same source of supply. A first article sample or portion thereof, as directed by the procuring agency, shall also be submitted whenever a ch

32、ange occurs in specification, or source of supply, such as to significantly affect product uniformity as determined by the responsible government technical agency. The first article sample shall consist of the following items in quantities indicated. 0 Part Description Drawings Quantity Cup (uncoate

33、d) 11 735,732 Cup (coated) 1 1735732 Collar (uncoated) 11735733 Collar (coated) 1 1735733 Base (uncoated) 1 1735735 Base (coated) 1 1735735 Test Panels (See MIL-C-46487) - Cartridge Case Body Blank - Cartridge Case (M148AlBlEl) 11 735736 4 10 4 10 4 10 2 4 254 4.4.2 Inspections to be performed. See

34、MIL-A-48078 and Table I specified herein. 4.4 . 3 Rejection. See MIL-A-48078 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-h rl P m m 4 a, m (u u a, ho a .rl L Q L m u w m 4 Co =i- kir tC 8 r r 7 t- M -*=i- -*=i- M M M M M MMM MMM . 0 n -a CU +,

35、mm OM Ot- cm 3M wt-m n a a)Ln m +, c) a, 4-l a, am m LCU m .lJ O a, 4-l a, am m U a, v) 3 a, c, O S n 2 E -c U r 3 n In a3 a, LL n n O h In $4 v) a, U lu a, CY F n m a3 3 3 t-l n O h In t-l 7 n E 5 O LL o r: L O 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

36、from IHS-,-,-n p: 4 O In m O b I * I cl H c v C a m L m rl O Wi-I E* MIL-C-70750 33 W 7777706 0370337 2 W Cu Y rld rl m -Cu HHHHHHHHHHH HH HH HHHHHHHHHHH- . HHNN HH a, a,a,a,a,a,a,a,a,a,a,a,a ocuaa drlrlrlrlrlrlrldrlrl rlrl rlrl mmmmmmmmmmm mm MPBMwMwwBww* WB3* Mw PPPPPPPPPPPIn PPInIn PP mm a, a a,

37、c O z L O a, w c a rl lU1 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-nl LL O 7 E I fn a, m $ M In Ln 3 . . e HH HH HHHHHHH HH HHH HHH HH HH HHHHHHH HH HHH HHH a, 00 a,a,a,a,aa,a, a, a, alala, rld drl ddddddd dri drid ddrl PP PP PPPPPPP PP PPP

38、 PPP mm (IIm mmmmm(IIm mm mmm mmm wB PB wwBBwBP BP BPE-c PE+P b a, c rl U a, O a, C O 4 :I LI 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-70750 13 7779706 0370321 O W - - - P a U L C U o C F I c . + E r 8 HHH H H HHH a, a,a,a, Ti rldd P

39、PPP m m(I(I P Bl3B L O ho a, c m *rl (I m m P .-I 6i s ob) 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-70750 13 7797706 0370322 2 Cu LLi O r E I v) 7 7 .- r Y“? “ =r“ Y *. . . . . . MM (u? M M MMMM MM MMO M HH H H H HHHH HH HHH H HH H H

40、H HHHH HH HHH H a, a, a, a, a,a,a,a, a, ala, a, rlrl rl rl d rlrlrlrl rlrl drlrl rl PP P P P PPPP PP PPP P mm m (1 m cumma mm mmm a WE-c B B B E-cE-cBE-c BB bBB E-c a a, e ad bi a, a a, e O 2 14 e Y 0 a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

41、-MIL-C-70950 13 = 7799906 0370323 4 -_. n 4 W O In 3 O + I u I IJ H c U Cu LL O Cu ti I v) W I I P Cucu Cu HHHHH *. H* HHH HHHHH HHH- NCUM M H =f LI a, c c .rl k O a, tnl a a, O a rl g k O ne ao - .rl hL ac c L al O 33 O L a, 2 k O a, M a a, O s, a rl !2 (H O c O 15 Provided by IHSNot for ResaleNo r

42、eproduction or networking permitted without license from IHS-,-,-MIL-C-70750 13 7777706 0370324 b 4.5.6 Testing. This section describes sampling plans, criteria for acceptance or rejection of individual samples, and criteria for acceptance or rejection of the entire lot. 4.5.6.1. Hardness. Ten sampl

43、es shall be randomly selected for testing. Failure of one hardness reading is cause.for rejection of the sample. Failure of one sample is cause for rejection of the lot. 4.5.6.2 Protective coating . 4.5.6.2.1 Coating thickness. Samples shall be selected in accordance with Table II. Failure to comply

44、 with the thickness requirement in the component drawing shall be cause for rejection of the sample. Failure of one sample shall be cause for rejection of the lot. 4.5.6.2.2 Salt spray. Five samples shall be randomly selected for testing. Samples shall be evaluated at the end of the test period in a

45、ccordance with the detail specification for the protectivg finish. The cartridge case assemblies subjected to the salt spray test shall show no more than 1/8 inch creepage, blistering, or loss of adhesion of the coating from the scribe mark. At all other points, there shall be no more than a trace o

46、f film failure (rust grade 9 ASTM D-6101, and not more than 5 scattered blisters none larger than lmm (3/64 inch) in diameter on a 48 square inch area. Rust within one thirty second (l/32) inch of all other edges shall be permitted. Failure to comply shall be cause for rejection of the sample. Rejec

47、tion of one sample shall be cause for rejection of the lot. to determine the integrity of the assembly, two samples shall be inspected during each shift or eight hour production period. One sample shall be from the middle and one from the end of the shift. If any change is made to the assembly proce

48、ss, another sample shall be inspected. Failure of any sample to comply with requirements shall be cause for rejection of all production subsequent to the last acceptable inspection. 4.5.6.4 Ballistics. Physical evidence of noncompliance with the applicable table below, with or without video indications is cause for rejection. Video detection of emissions from the breach area alone is insufficient cause for rejection. 4.5.6.3 Distance from base O.D. to edge of body plies. In order 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,