ARMY MIL-C-71144-1994 CHARGE PROPELLING M229 FOR 105MM HOWITZER LOADING ASSEMBLING AND PACKING《105MM榴弹炮组装及包装用M229型发射装药》.pdf

1、MIL-C-71144 W 99Ob 1988596 2Lb INCH-POUND 1 MIL-C-71144 (AR) 27 September 1994 MILITARY SPECIFICATION CHARGE, PROPELLING, MZ29, FOR 105MM HOWITZER LOADING, ASSEMBLING AND PACKING This specification is approved for use by the US Army Armament, Munitions and Chemical Command and is available for use b

2、y all Departments and Agencies of the Department of Defense. 1. SCOPE. 1.1 Scone. This specification covers the requirements, examinations and tests for the loading, assembling and packing for one type of propelling charge designated as Charge, Propelling, M229, for Howitzer M119 and is intended for

3、 use in the M913 RA cartridge. 2. APPLICABLE DOCUMENTS 2.1 Gove rnment docu ments. 2.1.1 Snec ifications, Sta ndards a nd handboo ks. The following specifications, standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these doc

4、uments are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS MILITARY MIL-P-193 - Potassium Sulfate (For MIL-A-48078 - Ammunition, Standard Quality Ordnance Use) Assurance

5、Provisions, General Specification for Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document, should be addressed to: Commander, U.S. Army, ARDEC, ATTN: SMCAR-BAC-S, Picatinny Arsenal, NJ 07806-5000 by using the Standardizati

6、on Document Improvement Proposal (DD Form 1426) appearins at the end of this document or by letter. AMSC N/A FSC 1315 DISTRIBUTION S TATEMENT A. unlimited. Approved for public release; distribution is Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M

7、IL-C-71144 m 9999906 I1988577 152 m MIL-C-71144 (AR) . MIL -C -4 8 3 6 O - Charge, Propelling, M200, for 105MM Howitzer, M119, Loading, Assembling and Packing - Propellant, M30 for Use in Charge, Propelling, 105MM, M200 MIL-P-7053 9 STANDARDS MILITARY MIL-STD-109 MIL-STD-1168 - Quality Assurance Ter

8、ms and - Lot Numbering of Ammunition Definitions (Unless otherwise indicated, copies of the federal and military specifications, standards, and handbooks are available from the DODSSP - Customer Service, Standardization Documents Order Desk, Bldg 4D, 700 Robbins Ave., Philadelphia, PA 19111- 5094. )

9、 2.1.2 Qther Gove rnment docume nts, d rawinas. and gublicatio ns. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS US ARMY ARMAMENT R

10、ESEARCH DEVELOPMENT AND ENGINEERING CENTER (ARDEC) 9282042 9345265 12630698 12630699 12953551 - Charge, Propelling M200 Loading Assembly - Container, Steel - Flash Reducer Loading Assembly for 105MM M229 Propelling Charge - Charge, Propelling 105MM M229 - Packing and Marking for Container, Steel for

11、 105MM Howitzer Propelling Charges (Copies of other Government documents, drawings and publications acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) required by contractors in connection with specific 2.2 Order of mecede nce. the tex

12、t of this document and In the event of a conflict between the references cited herein, the 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-7L144 m 9999906 1988598 O99 m MIL-C-71144 (AR) text of this document takes precedence. Nothing in this

13、document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. for additional precedence criteria.) (See contract provisions 3. REQUIREMENTS. 3.1 Mate rial. Material shall be in accordance with applicable drawings and specifications. 3.2 Pronellina chara

14、e assemb IV. The M229 propelling charge consists of an M200 charge as the main increment loaded in accordance with drawing 9282042 which meets all of the requirements of MIL-C-48360 (with the exception of marking requirements) and a flash reducer assembly loaded in accordance with drawing 12630698 s

15、ewn to the main charge assembly. The complete assembly shall comply with all requirements specified on drawing (dwg) 12630699 and with all the requirements specified in applicable specifications. 3.3 ProDe llant we iaht. 3.3.1 Flash reducex . The flash reducer assembly shall be loaded with 3.0 2 0.0

16、5 ounces of M30 propellant conforming to the requirements of MIL-P-70539 and 1.5 2 0.05 ounces of Type II potassium sulfate meeting the requirements of MIL-P-193. 3.3.2 Flash reduce r assemb IV we iaht. The flash reducer assembly weight shall not differ by more than i 0.10 ounces from the total weig

17、ht of the propellant, plus that of the potassium sulfate, plus the average tare weight of the bag assembly. 3.3.3 Chame. n roDellina assemb IV we iaht. The charge, propelling assembly weight of the M229 propelling charge shall not differ by more than 2 0.15 ounces from the total weight of that speci

18、fied on the loading authorization plus the average tare weight of the bags. 3.4 provinu around. Ballistic testing shall be performed on the main increment of the charge only. The charge when tested in accordance with 4.4.3.3 shall meet the ballistic requirements of MIL-C-48360. 3.5 First a rticle in

19、mectio n. Test samples shall be withdrawn from the first lot produced by the contractor. Samples will be tested in accordance with all the requirements of this specification. Until the first article test has been performed and found to be acceptable, the contractor is in no way authorized by the Gov

20、ernment to initiate production of a second lot unless otherwise directed by the contracting officer. specification contains provisions for the submission of a initial 3.6 Jnitiai moduct ion insnect ion (see 6. 7). This 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without li

21、cense from IHS-,-,-MIL-C-71144 = 999990b 1988599 T25 W MIL-C-71144 (AR) production sample. This is a one time qualification test for a new contractor to load assemble and pack M229 propelling charges. Test samples shall be withdrawn from the first lot produced by the contractor. Charges will be test

22、ed in accordance with all the requirements of,this specification and with Table III (see 6.7). Until the initial production sample has been found to be acceptable, the contractor is in no way authorized by the Government to initiate production of a second lot unless otherwise directed by the contrac

23、ting officer. 3.7 JrJorkmans hin. The propellant grains shall be free of dirt, foreign material and other defects that would make the item unsuitable for its intended use. The cloth and thread used for the manufacture of propelling charge bags shall be void of grease, oil, dirt, foreign material, ho

24、les, rips or tears. All components and assemblies shall be fabricated and finished in a thorough workmanlike manner. All required marking shall be neat and sharply defined. 4. QUALITY ASSURANCE PROVISIONS 4.1 Remo nsibilitv for inmect ion. Unless otherwise specified in the contract or purchase order

25、, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requ

26、irements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set for in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Pesoons ibilitv for

27、 comD liance. All items shall meet all requirements of Sections 3 and 5. The inspections set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contract

28、or of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does

29、 authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.1.2 General Drovisions. Unless otherwise specified herein, the provisions of MIL-A-48078 apply and form a part of this specification. References shall be m

30、ade to MIL-STD-109 to define quality assurance terms used herein. 4.2 Classification of inmect ions. The inspection requirements specified herein are classified as follows: 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-71L44 9999906 1988600

31、 577 = MIL-C-71144 (AR) a. Initial Production Inspection (see 6.7). b. First Article Inspection (see 4.3). c. Quality Conformance Inspection (see 4.4). 4.3 First a rticle inmection. 4.3.1 Sub mission. The contractor shall submit a first article sample as designated by the contracting officer for eva

32、luation in accordance with the provisions of 4.3.2. The first article sample shall consist of fifteen (15) propellant charge assemblies packed in a fiber drum and fifteen (15) complete sets of parts (i.e. 15 each of every component and every sub assembly) which have been produced by the contractor.

33、4.3.2 nsnectio ns to be re rformed. The first article assemblies submitted in accordance with 4.3.1 will be subjected by the Government to any or all of the requirements of the applicable drawings and to the inspections and tests of Table I. All inspections in Table I shall be classified Major unles

34、s otherwise specified. 4.3.3 Reiect ion. If any assembly, component or test specimen fails to comply with any of the applicable requirements, first article sample shall be rejected. The Government reserves the right to terminate inspection upon any failure of an assembly, component or test specimen

35、to comply with any of the requirements. the 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-7LL44 m 999990b l1988b01 403 m I rl 8 rl t w I v) 1 ! - i rl (u di di m N dc di di Cu di di N m N m N m N m do do O O O O rl rl ow do O O O O rl I4 6

36、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-7LL44 99Ob l1988b02 34T = MIL-C-71144 (AR) 4.4. Oua litv CO nformance inmection. 4.4.1 I ; rm i n. Inspection lots shall comply with the lot formation provisions of MIL-A-48078 and MIL-STD- 1168.

37、In addition: a. Flash reducers shall contain M30 propellant, Type I, from not more than one lot from one manufacturer. b. Main increments shall contain propellant from not more than one lot. c. The same lot of propellant loaded into the main increment shall be loaded into the flash reducer. d. Potas

38、sium sulfate from not more than one manufacturer. e. An entire lot of M30 propellant shall be used to form a lot of M229 propelling charges unless otherwise directed by the contracting officer. 4.4.2 Examinatio n and tests . See MIL-A-48078. a. Classif ication of c haracte risticg. Quality conforman

39、ce examinations and tests are specified in the following Classification of Characteristics paragraphs. The contractors quality program or detailed inspection system shall provide assurance of compliance of all characteristics with the applicable drawings and specification requirements utilizing as a

40、 minimum the conformance criteria specified. When cited herein, attributes sampling inspection shall be conducted in accordance with Table II below, using the inspection levels stated in the Classification of Characteristics paragraphs. TABLE II Attributes sa mDle inmect ion levels. Lot Size 2 to 8

41、9 to 15 16 to 25 26 to 50 51 to 90 91 to 150 151 to 280 Major Sample Size * * it 32 32 32 32 281 to 500 32 501 to 1200 74 1201 to 3200 74 10001 to 35000 109 3201 to 10000 87 35001 to 150000 124 150001 to 500000 156 500001 and over 187 * - 100 % inspection Minor Sample Size see note 5 5 5 12 12 14 17

42、 20 24 30 36 40 40 40 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-C-7bbY4 9999906 LBBb03 286 MIL-C-71144 (AR) ? NOTE: Use 100 % inspection when lot size is less than 5 units. Use sample size when lot size is greater than 5 units. b. Altern

43、ative aua litv con formance D rovi sions. Unless otherwise specified herein or provided for in the contract, alternative quality conformance procedures, methods or equipment, such as statistical process control, tool control, other types of sampling procedures, etc. may be used by the contractor whe

44、n they provide, as a minimum, the level of quality assurance required by the provisions herein. Prior to applying such alternative procedures, methods, or equipment, the contractor shall describe them in a written proposal submitted to the Government for evaluation (see 6.9). When required, the cont

45、ractor shall demonstrate that the effectiveness of each proposed alternative is equal to or better than the specified quality assurance provision(s1 herein. In cases of dispute as to whether the contractors proposed alternative(s1 provides equivalent assurance, the provisions of this specification s

46、hall apply. All approved alternative provisions shall be specifically incorporated into the contractors quality program or detailed inspection system, as applicable. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-d MIL-C-71144 m 9999906 1988604 11

47、2 m rla r mm m rld rl II I *n-n -n a, a, lxp: O0 O II I UU u 22 2 a a rn rn a h rl k bi a o f? C -4 rn k rn -4 E TI rn ubi dC Q) -4 UA CU oa UP( bi c -4 x u a a -II di ki ki JI OldN 014 4 I -nIOO -nIO I 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

48、,-,-MIL-C-71144 W 9999906 1988610 416 m d U O rl t W I v) rlrl rlrt rl drl ddd rl II III I -n-n Vn-n-n -n a, alua, a, CG CGP: P:CGCG O0 O00 O II III I uu uuu u uu uuu 44 444 2 h d .k aa, Q,a JJO rlk 4 a JJE -rl m -4 k O ka, am 573 k O Q O & 00000 O0 O00 00000 O0 III rlrldrld drl uuu 222 L, s! k O ao

49、 OE: ici Wk JJ 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-C-LIJ 9999906 L988bL2 299 MIL-C-71144 (AR) 4.4.3 Testinq. 4.4.3.1 Flash reduce r DroDellant we iaht. The propellant to be loaded into the flash reducer increment shall be weighed and check weighed 100 percent. Any propellant which