ARMY MIL-D-63266-1978 DOCUMENT DESTROYER EMERGENCY INCENDIARY M4《M4型紧急燃烧弹文件破碎机》.pdf

1、 - MIL-D-63266 13 E 7779706 0346825 7 - MILITARY MIL-D-63266 (AR) 8 March 1978 SPECIFICATION DOCUMENT DESTROYER, EMERGENCY INCENDIARY: M4 This specification is approved for use by U.S. Army Armament Reasearch and Development Command and is available for use by all Departments and Agencies of the Dep

2、artment of Defense. 1. SCOPE ance date part 1.1 T-his document covers requirements and quality assur- provisions for one type of incendiary device. 2, APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on of invitation for bids or request for proposal, form a of this specificati

3、on to the extent specified herein: SPECIFICATIONS MILITARY MIL-F-18405 - MIL-A-48078 - STANDARDS MILITARY MIL-STD-105 - MIL-STD-1168 - DRAWINGS Fuze, Firecracker, 30-second Ammunition, Standard Quality Assurance Provisions, General Specification For Sampling Procedures and Tables for Inspection by A

4、ttributes Lot Numbering of Ammunition US ARMY ARMAMENT RESEARCH AND DEVELOPMENT COMMAND D4-11-47 - Document Destroyer, Emergency Incendiary: xM4 FSC: 1375 Banef icid comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addre

5、ssed to: Commander, US Army Armament Raaearch and Development Command, Attn. DRDAR-QA, Dover, New Jersey 07801 by using the self-addressed Standardization Document Improvement Ropoad (DD Form 1426) appearing at the end of thin document or by letter. - Y THIS DQCUNIENT CONTAINS a PAGES. Provided by I

6、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-63266 13 = 779770b 03Lib82b 7 (Copies of specifications, standards, drawings and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activ

7、ity or as directed by the contracting officer.) 3. REQUIFU3MENTS 3.1 Materiais. - Materials shall be in accordance with the applicable drawings and specifications. 3.S Components and assemblies. - The components and assemblies shall comply with all requirements specified on drawings D4-11-47 and D4-

8、11-46 and all associated drawings and with all requirements specified in applicable specifications and standards. 3.3 Functioninq 3.3.1 Igniter. - The igniter, drawing C4-11-51, shall ignite and completely burn within 24 + 8 seconds when tested as specified in 4.5.3. - 3.3.2 Document destroyer. - Th

9、e document destroyer shall ignite and completely burn a minimum of 98 percent by weight of 100 pounds of paper products to be reduced to ash-within 20 minutes after ignition. The paper products shall be placed in the inner drum in accordance with the operational instruction card, drawing D4-11-52, a

10、nd tested as specified in 4.5.4. The paper products shall consist of the type and quantity of paper in Table III. 3.4 Leakage. - The sealed document destroyer shall main- tain a pressure of 15 PSIG for 3 minutes with leakage not to exceed 1 PSIG when tested as specified in 4.5.5. 3.5 Workmanship. -

11、The parts and assemblies shall be free from chips, dirt, grease and other foreign matter that may impair proper functioning. The cleaning method used shall not be injurious to any of the parts, nor shall the parts be con- taminated. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection a

12、nd standard quality assurance provisions. - Unless otherwise specified herein or in the contract, the provisions of MIL-A-48078 shall amlv - and are hereby made a-part of this detail specification. 4.2 Classification of inspection. - The following types of inspection shall be conducted on this item:

13、 a. First Article Inspection b. Quality Conformance Inspection 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-63266 (AR) TABLE III - PAPER PRODUCTS MIX Item Thickness Percent Approx . Inches by Weight Height Inches A. Military technical manu

14、als, pamphlets, and directives 1/8-1/2 50 16 B. Computer data runs 1-3 7.5 3 C. Military pamphlets and directives 3/4-1 1/2 7.5 2 1/2 O D. Telephone books or Federal registers 1/2-2 7.5 max 2 1/2 E. Glossy magazines 1/4-1/2 5.0 max 1 1/2 F. Bond paper loose in folders 15.0 5 G. Data process cards lo

15、ose in folders 7.5 2 Notes: 1. Place computer runs and glossy paper in bottom of Irum . of A and F. 2. Alternately layer approximately 2 inch thick stacks 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-63266 (AR) 4.3 First article inspection

16、 4.3.1 Submission. - The contractor shall submit a first article sample as designated by the Contracting OEficer for evaluation in accordance with provisions of 4.302. The first article sample shall consist of the following items in sample quantities as indicated. Part Description Drawinp Quantity I

17、gniter C4-11-51 Igniter Assembly C4-11-53 Emergency Incendiary D4-11-4 7 Document Destroyer 6 6 5 4.3.2 Inspections to beperformed. - See MIL-A-48078 and Table I specified herein. 4.3.3 Rejection. - See MIL-A-48078. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

18、se from IHS-,-,-5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-b326b 13 m 9999906 0346830 O MIL-Da3266 (AR) 4.4 Quality conformance inspection 4.4.1 Inspection lot formation. - Inspection lots shall comply with the lot formation provisions o

19、f MIL-A-48078. addition, inspection lots of Document Destroyers shall contain: In a. Not more than three batches (see 6.5) of Ignition Mixture Igniter Charge of one interfix number from one manu- facturer. one manufacturer shall not contain more than one interfix number of each chemical element. In

20、addition any one interfix number of Igniters from b. Not more than one interfix number from one manu- facturer of-xidizing Agent NO3- Charge I. 4.4.2 Examination. - See MIL-A-48078. a. Sampling plans. - Unless otherwise specified in the Classification of Defects and Test Tables, sampling plans and p

21、rocedures for major and minor defects shall be in accordance with MIL-STD-105, Inspection Level II. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-D-63266 13 7777906 03Lib83L 2 E rl 8 FI w m al M k ld ;b; M k al ci 4 U al k 3 U t4 .i( c Q M

22、ir( 4J cd H N ? I I n ld v U E U Q a al F o +I w al al 3 U a al m z 4 2 Q a al e ad w al al z a, Q 7 k O u4 c al U % alk c)aJ au4 GO (d h U aJ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-r MIL-D-63266 23 797770b 0346832 Li U k al U +I :u :El wwwm

23、w vi mmmmm m . O00 o O ddd d O . O00 o rl n (d U U o al tf k O O a rei rl Cdl -. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-O0 Ur0 wo 4.4. O0 Orl a al c 4 w al a al z g rl fdl 9 Provided by IHSNot for ResaleNo reproduction or networking permitte

24、d without license from IHS-,-,-4 w r. 4 E - MIL-D-632bb 13 977790b 0346834 O0 Ur0 WO e* I. a 4 u al w al z c Co d CUI I I 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I a .r( u-i al a al z 2 !? E al v) v) m h rl a 4 5 B k k O O a u-i O al o a I

25、4 3 w Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-= . I I I I a rl m B k h rl U k o al - O a rw O l-4 O rl 12 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4 MIL-D-63266 13 I 7799706 0346837 3

26、 I 3 2 m *I4 .I4 3 3 a 2 h I4 u u aJ k k O 2 a m G 4 k O a w O a al U a a d al c .r( k 3 I Eil z f Q FI LdI 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-n Ly d v Co m .Fu rT Co I 4 W a M k (d ;Cu I m O z U 5 3 2 2 4 N .rl X O Fu ? d I I n (d W

27、u o a a c o a d iw a a a z $ g 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-D-b3266 13 I 77777Ob 03Lih37 7 I 3 m I P Y t I P s W 2 * E h k (d 4 a ti 2 s pf H h o M 6 w k - E w u u) al FI tJ ti 0 O n rl dd (v (v (v (vm(v(ve m rl rlmrlmm . .

28、 . . . . . ln m o o o O00 O e e * e* O o o o O00 d . . . . n cd W a d rcc al a al z z al M k (d .Cu I m F d u) u) *d e k O al rl a -4 -2 k k O O a ci O al o a d 3 w $ rl lUl 81 $I rcc O al k al s U Co .d U o (d k rcc k O U O rl (d C .d u) Qi U .d O O rl h k al Q, k O Qi U .d al al a rl rl 2- al N .d

29、 u) al rl a E. (d VJ n (d U 15 .I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-b32bb 13 9797706 03LI68LIO 3 MIL-D-63266 (AR) 4.4.3 Testing. - Testing is described in the First Article and Quality Conformance Inspection tables. 4.4.4 Inspecti

30、on equipment. - The inspection equipment required to perform the examinations and tests prescribed here- in is described in the “Paragraph Reference/Inspection Method“ column in the tables starting with paragraph 4.4.2.1. The contractor shall submit for. approval inspection equipment designs in acco

31、rdance with the terms of the contract. See Section 6 of MIL-A-48078 and 6 herein. 4.5 Test methods and procedures. - 4.5.1 Materiais, components and processes. - Compliance with all requirements of Section 3 of this specification shall be ascertained by current and continuing examination of inspect-

32、 ion and test data to determine that all components (parts, subassemblies, and materials) have been inspected and tested and found to comply with their respective drawing and specifi- cation requirements, and that all specified manufacturing pro- cesses have been followed. 4.5.1.1 Visual and mechani

33、cal inspections. - The visual, manual and mechanical inspections and tests shall verify com- pliance with the requirements of Sections 3 and 5 of this specification in accordance with 4.4.2 herein and Table I. 4.5.2 Moisture content. - Place 5 grams of the material to be testea into a tared weighing

34、 dish. Place in an oven main- tained at 100C for 3 hours. -Cool in a desicator and weigh. Calculate the loss in weight of contents as the percent moisture. C4-11-50 spaced 2 + % inches above a flat horizontal noncom- bustible surface. burning by directing the fuzee at one end, with the fuzee paralle

35、l to the igniter axis. burning. Record the time required to burn the igniter. Remove the hot ashes from the screen and cool the surface area before repeating the test. 4.5.3 Igniter. - Place a screen conforming to drawing - Use a M72 fuzee to start the igniter charge Start timing when the igniter ch

36、arge starts 4.5.4 Document destroyer. - Set up and operate the document destroyer in accordance with the preparation and oper- ational instructions, drawings D4-11-49 and D4-11-52. Start timing when the igniter starts burning. At 19 minute, remove the lever lock ring and screen and at 20 minutes tip

37、 the drum on its side. to ash and immediately extinguish by smothering. unburned paper products. Rake out and recover any paper products not reduced Weigh the 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-D-63266 13 W 7977706 0346841 5 W 4

38、MIL-D-63266 (AR) 4.5.5 Leakaqe. - Connect the document destroyer to a source of dry air (.75 percent maximum moisture content) by securing an adapter (containing a pressure gage with a shut- off valve in the line) to the threaded flange on the top head of the drum. Subject the document destroyer to

39、the air press- ure; when stabilized at the required pressure (15 PSIG) , close valve, and observe for a drop on the pressure gage for a min- imum of 3 minutes. Record any pressure drop observed. 5. PACKAGING 5.1 Packinq. - Packing shall be as specified on drawings D4-11-46 and D4-11-47. 5.2 Marking.

40、 - Marking shall be as specified on drawing D4-11-47. 6. NOTES 6.1 Intended use. - The item covered by this specification is intended for the emergency destruction of documents. 6.2 Ordering data . - See MIL-A-48078. 6.3 Submission of inspection equipment designs for approval. - See MIL-A-48078. Sub

41、mit equipment designs as required to Commander, U.S. Army Armament Research and Development Command, ATTN: DRDAR-QAA-I, Dover, New Jersey 07801. 6.4 Caution. - Suppliers are advised to take all necessary precautions to protect personnel while filling, assembling, and testing document destroyers due

42、to the incendiary nature of the item and test pressure requirements. 6.5 Batch. - A batch is defined as that quantity of material which has been manufactured by some unit chemical process and subjected to some physical mixing operation in- tended to make the final product substantially uniform. 6.6

43、Dyawinqs. - Drawings listed in Section 2 of this specification under the heading US Army Armament Research and Development Command (ARRADCOM) may also include drawings prepared by, and identified as, Edgewood Arsenal, Frankford Arsenal, Rock Island Arsenal or Picatinny Arsenal drawings . Technical d

44、ata originally prepared by these activities is now under the cognizance of ARRADCOM. Custodian : Army-AR Preparing Activity: Ar my- AR *V.S. GOVERNMENT PRINTING OFFICE: 1978-703-122/4111 Project Number: 1375-A-215 17 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-