ARMY MIL-DTL-3943 305 B-2013 DECORATION PUBLIC SAFETY OFFICER鈥橲 MEDAL OF VALOR U S DEPARTMENT OF JUSTICE.pdf

1、 AMSC N/A Page 1 of 4 FSC 8455 INCH - POUND MIL-DTL-3943/305B 21 November 2013 SUPERSEDING MIL-DTL-3943/305A 30 June 2007 DETAIL SPECIFICATION SHEET DECORATION, PUBLIC SAFETY OFFICERS MEDAL OF VALOR, U.S. DEPARTMENT OF JUSTICE This specification is approved for use by all Departments and Agencies of

2、 the Department of Defense The requirements for acquiring the product described herein must consist of this specification sheet and the latest issue of MIL-DTL-3943. PENDANT - OBVERSE PENDANT - REVERSE SUSPENSION WREATH ASSEMBLED - OBVERSE ASSEMBLED - REVERSE DASH NUMBERS: -1: Pendant -2 Suspension

3、Wreath -3: Assembled Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3943/305B Page 2 of 4 MATERIAL (-1 and -2): Red Brass 85/15 (UNS Alloy Number C-230) DIMENSIONS: HEIGHT: -1 (including lug): 1-27/32 inches (REF) -2: 3/4 inch (REF) -3: 2-1/

4、2 inches 1/32 inch WIDTH: -1, -3: 1-5/8 inches (REF) -2: 11/16 inch (REF) THICKNESS: -1 (across center): 0.120 inch 0.010 inch -2 (at edge): 0.0675 inch 0.010 inch PIERCINGS: -1 will be pierced in all shaded areas indicated above. FINISH (-1 Obverse & Reverse and -2): 24K Gold Plated, Matte Finish,

5、Polished Highlights and must match The Institute of Heraldry (TIOH) Metal Finish Chip Number 8. EPOXY: Epoxy enamel shall be applied to -1 as indicated below, and must match TIOH Hard Enamel Color Chip Number listed: TIOH HARD ENAMEL COLOR CHIP NUMBER LOCATION Blue #20 Arms of star Hard cloisonn ena

6、mel may be used in lieu of epoxy for -1. If hard cloisonn enamel is used, the required base material for -1 is Gilding Metal 95/5 (UNS Alloy Number C-210). ATTACHING DEVICES: ATTACHING DEVICE FOR PENDANT AND SUSPENSION WREATH: -2 must be secured to -1 by a hinge joint. The hinge will be 1/8 inch 1/6

7、4 inch long on either side by 3/32 inch 1/64 inch wide (see illustration below). The hinge must be hard soldered to the vertical center line of -2 1/32 inch + 1/64 inch 0 up from its bottommost point. The arm for the hinge joint is integral to -1, and is 3/32 inch 1/64 inch high by 1/32 inch 1/64 in

8、ch wide by 3/32 inch 1/64 inch deep. ATTACHING DEVICE FOR PENDANT AND NECKBAND: The suspension ring through which the neckband passes must be made of Red Brass 85/15 (UNS Alloy Number C-230) and conform to the dimensions specified below. The pendant ring will be hard soldered to the reverse of -2 as

9、 shown below, and in such a way that it is not visible when viewing the assembled decorations obverse. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3943/305B Page 3 of 4 NECKBAND: The neckband must conform to Figure 9 in the latest version

10、 of MIL-DTL-3943, except that the manufacturer may deviate from this drawing by increasing the finished length of the neckband to 26 inches + 1/2 inch - 0. DECORATION CASE: The decoration set will consist of a neckband with pendant and suspension wreath (assembled), a service ribbon with ribbon atta

11、chment, and a lapel button all Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3943/305B Page 4 of 4 packaged in a decoration case conforming to MIL-C-14633, Type VII, Style 3 with a Class 1 or 1A pad. The following shall be inscribed on the

12、top of the decoration case using three lines: (1) PUBLIC SAFETY (2) OFFICERS (3) MEDAL OF VALOR. NOTES: 1. The term (REF) refers to the measurements taken from the obverse Government furnished hub or die. 2. For -1 and -2, the manufacturer may deviate from MIL-DTL-3943 by using nickel underplating p

13、rior to plating with 24K gold. 3. The specification slash sheet for the neckband and service ribbon is MIL-DTL-11589/572. 4. The specification slash sheet for the lapel button is MIL-DTL-11484/289. 5. The specification slash sheet for the ribbon attachment is MIL-DTL-41819/46. 6. These items are not

14、 authorized for commercial sale, and may be produced only under Government contract and at the request of the U.S. Department of Justice. Custodian: Preparing activity: Army - IH Army - IH Civil Agency: (Project No. 8455-2014-002) DOJ - BJA NOTE: The activities listed above were interested in this d

15、ocument as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-