ARMY MIL-DTL-44036 A-2003 TIEDOWN ASSEMBLY CARGO AERIAL DELIVERY LOAD BINDER TYPE《锁紧器类型 云梯运输和货物拴住装置》.pdf

1、 Beneficial comments (recommendations, additions, deletions) and any pertinent data that may be of use in improving this document should be addressed to: Natick Soldier Center ATTN: AMSSB-RAD-AD(N), Natick, MA 01760-5017, using the Standardization Document Improvement Proposal (DD Form 1426) appeari

2、ng at the end of this document or by letter. AMSC N/A FSC 1670 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. MIL-DTL-44036A 30 JUNE 2003 SUPERSEDING MIL-T-44036 29 DECEMBER 1980 DETAIL SPECIFICATION TIEDOWN ASSEMBLY, CARGO, AERIAL DELIVERY, LOAD BINDER TYPE This s

3、pecification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for one type of load binding system in cargo aircraft. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are cited in

4、sections 3 and 4 of this specification. These lists do not include documents cited in other sections of this specification or recommended for additiona l information or as examples. While every effort has been made to ensure the completeness of these lists, document users are cautioned that they mus

5、t meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications and standards. The following specifications and standards form a part of this document to the extent herein. Unless otherwise sp

6、ecified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS INCH-POUNDProvided by IHSNot for ResaleNo reproduction or networking permitted

7、without license from IHS-,-,-MIL-DTL-44036A 2 DEPARTMENT OF DEFENSE MIL-DTL-43021 - Binder, Load, Cargo Tie-down, 10,000 Pounds (44.5 kN) Capacity MIL-W-43342 - Webbing Assembly, General Specification for (Unless otherwise indicated, copies of the above specifications, standards, and handbooks are a

8、vailable from the Standardization Document Order Desk, 700 Robbins Avenue, Building 40, Philadelphia, PA 19111-5094) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified

9、 herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS NATICK SOLDIER CENTER 11-1-892 - Strap, Tie Down, Cargo Heavy Duty (Copies are available from the Natick Soldier Center, ATTN: AMSSB-RAD-AD(N) CONFIGURATION MANAGER, Natick, MA 01760-5017.) 2.3 Non-Governme

10、nt publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents that are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of document

11、s not listed in the DoDISS are the issues of the documents cited in the solicitation. PARACHUTE INDUSTRY ASSOCIATION PS22046-8 - Dee Ring (Application for copies should be addressed to the Parachute Industry Association, 3833 West Oakton Street, Skokie, IL 60076.) 2.4 Order of precedence. In the eve

12、nt of a conflict between the text of this document and the references cited herein (except for related associated specifications or specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemp

13、tion has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to a first article inspection in accordance with 4.2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44036A 3 3.2 Materials and

14、construction. Materials and construction details shall conform to the requirements of the applicable specifications and as specified herein. A tie-down assembly shall consist of one of the following items: 3.2.1 Load binder. The load binder shall be in accordance with the requirements of MIL-DTL-430

15、21. 3.2.2 Tie-down strap. The tie-down strap shall be in accordance with the requirements of MIL-DTL-43342 and Drawing 11-1-892. 3.2.3 “Dee” ring. The dee ring shall conform to the requirements of PIA Standard PS 22046-8. 3.3 Marking. Identification marking of each component shall be in accordance w

16、ith the applicable specification or standard. 3.4 Workmanship. The workmanship shall conform to the quality established by the applicable specification. 4. VERIFICATION 4.1 Classification of Inspections. The inspection requirements specified herein are classified as follows: a. First article inspect

17、ion (see 4.2). b. Conformance inspection (see 4.3). 4.2 First article inspection. First article inspection shall be performed on one complete tie-down assembly, unless otherwise stated in the contract, when a first article sample is specified (see 3.1). The inspection shall include the tests and exa

18、minations of 4.3.1 and 4.4. Any defect or nonconformance shall be cause for rejection of the first article. 4.3 Conformance inspection. Conformance inspections shall include the examinations of 4.3.1 and 4.5 Sampling plans and acceptance/rejection criteria shall be as specified in the contract or pu

19、rchase order. Tie-down assemblies which fail the acceptance criteria shall be cause for rejection of the lot. 4.3.1 Component and material inspection. Components and materials shall be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modif

20、ied, or qualified in this specification or applicable purchase document. 4.4 Examinations. Each item (see 3.2.1, 3.2.2 and 3.2.3) shall be examined for conformance to the applicable specification. 5. PACKAGING Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

21、IHS-,-,-MIL-DTL-44036A 4 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of material is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertai

22、n requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments System Command. Packaging data retrieval is available from the managing Military Departmen

23、ts or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. The cargo tiedown assembly is intended for

24、securing general cargo and equipment for transport and air delivery. It can exert a binding force of up to 10,000 pounds. 6.2 Acquisition requirements. Acquisition documents should specify the following: a. Title, number and date of this specification. b. Issue of DoDISS to be cited in the solicitat

25、ion and if required, the specification of individual documents referenced (see 2.2.1). c. When a first article is required (see 3.1). d. Sampling plan (see 4.3). e. Packaging requirements (see 5.1). 6.3 Subject term (keyword listing). Restraint Secure Air delivery 6.4 Changes from previous issue. Ma

26、rginal notations are not used in this version to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing Activity: Army - GL2 Army - GL2 Air Force - 99 (Project 1670-1044) Review Activities: Air Force - 11 Provided by IHSNot for ResaleNo reproducti

27、on or networking permitted without license from IHS-,-,-STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL INSTRUCTIONS 1. The preparing activity must complete blocks 1, 2, 3, and 8. In block 1, both the document number and revision letter should be given. 2. The submitter of this form must complete bloc

28、ks 4, 5, 6, and 7. 3. The preparing activity must provide a reply within 30 days from receipt of the form. NOTE: This form may not be used to request copies of documents, nor to request waivers, or clarification of requirements on current contracts. Comments submitted on this form do not constitute

29、or imply authorization to waive any portion of the referenced document(s) or to amend contractual requirements. I RECOMMEND A CHANGE: 1. DOCUMENT NUMBER MIL-DTL-44036A 2. DOCUMENT DATE (YYYYMMDD) 20030630 3. DOCUMENT TITLE Tiedown Assembly, Cargo, Aerial Delivery, Load Binder Type 4. NATURE OF CHANG

30、E (Identify paragraph number and include proposed rewrite, if possible. Attach extra sheets as needed.) 5. REASON FOR RECOMMENDATION 6. SUBMITTER a. NAME (Last, First, Middle Initial) b. ORGANIZATION c. ADDRESS (Include Zip Code) d. TELEPHONE (Include Area Code) (1) Commercial (2) DSN (if applicable

31、) 7.DATE SUBMITTED (YYYYMMDD) 8. PREPARING ACTIVITY a. NAME Natick Soldier Center b. TELEPHONE Include Area Code) (508) 233-4258 c. ADDRESS (Include Zip Code) AMSSB-RAD-AD(N), J. Riley Natick, Ma 01760-5017 IF YOU DO NOT RECEIVE A REPLY WITHIN 45 DAYS, CONTACT: DD Form 1426, FEB 1999 (EG) Previous editions are obsolete WHS/DIOR, FEB 99 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-